2010 Chrysler 300 Drivetrain Parts

This table covers the actuators that engage four-wheel drive at the transfer case or axle. Typical signs include a door or range that will not move, or a click with no motion. Confirm the command signal before replacing the actuator — a failed module looks the same. Read more

2 4WD Actuator parts for the 2010 Chrysler 300 come from 2 brands — MOPAR and STANDARD MOTOR PRODUCTS.

This group includes MOPAR 68052258AA and STANDARD MOTOR PRODUCTS TCA118.

This table covers the Axle / Differential assemblies. Read more

5 Axle / Differential Assembly parts for the 2010 Chrysler 300 come from MOPAR. 1 part fits every engine; the other 4 are engine-specific.

This group includes MOPAR 4593844AA, MOPAR 52111503AH and MOPAR 52114391AE and the remaining parts above.

This table covers the Axle housings. Read more

One part is listed for the 2010 Chrysler 300 — MOPAR 5143949AA.

This table covers the seals where an axle shaft exits the housing. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

7 Axle Shaft Seal parts are listed for the 2010 Chrysler 300, from NATIONAL, WJB / INMOTION PARTS, ELRING and 2 other brands. NATIONAL 711054 carries the "Popular" badge. 4 parts fit every engine; the other 3 are engine-specific.

This group includes NATIONAL 711054, NATIONAL 711078 and ELRING B12920 and the remaining parts above.

This table covers the complete CV axle shafts from differential (or hub) to wheel. Typical signs include a click in tight turns, grease flung around the wheel well, or a vibration that builds with speed. A torn boot caught early is a boot kit; caught late it is the whole axle. Torque the axle nut to the method in the notes. Read more

41 CV Axle parts are listed for the 2010 Chrysler 300, from TRAKMOTIVE, TOP NOTCH, GSP and 4 other brands. FAMOUS BRAND NCV479097 carries the "Popular" badge. Grades run from Economy through Standard Replacement; Standard Replacement is the most populated section, led by TRAKMOTIVE, TOP NOTCH, GSP and 3 other brands.

This table covers the CV Intermediate shafts. Read more

This group shows a single part: DORMAN 630347.

This table covers the boots that keep grease in a CV joint. Typical signs include a split boot, grease flung around the joint, or a click once grit is inside. A boot caught early is a kit. Once the joint has clicked, the joint itself is usually worn. Read more

4 CV Joint Boot parts are listed for the 2010 Chrysler 300, from MEVOTECH and MOPAR. 2 parts fit every engine; the other 2 are engine-specific.

Part numbers include MEVOTECH DX516, MEVOTECH DX571 and MOPAR 5142215AA, among others listed above.

This table covers the Differential Bearing retainers. Read more

One part is listed for the 2010 Chrysler 300 — USA STANDARD GEAR USA33265.

This table covers the bearings and races that support the differential carrier. Read more

22 Differential Carrier Bearing / Race parts are listed for the 2010 Chrysler 300, from WJB / INMOTION PARTS, BCA, SKF and 3 other brands. WJB / INMOTION PARTS WTLM503310 carries the "Popular" badge. 10 parts fit every engine; the other 12 are engine-specific.

In the Economy grade, WJB / INMOTION PARTS supplies 7 parts: the catalog's value-priced group. A representative part number is WJB / INMOTION PARTS WTLM503310.

The Standard Replacement section lists 15 options from BCA, SKF, SCHAEFFLER and 2 other brands — built to original-equipment specification. BCA NBLM503349A is listed in this group.

This table covers the Differential Carrier bushings. Typical signs include a clunk over bumps, or a torn or walked-out bushing you can see. Press the new bushing square. A cocked bushing will tear in a few thousand miles. Read more

One part is listed for the 2010 Chrysler 300 — ENERGY SUSPENSION 51115G.

This table covers the Differential covers. Read more

This group shows a single part: MOPAR 5143120AA.

This table covers the Differential Cover bolts. Read more

One part is listed for the 2010 Chrysler 300 — MOPAR 5143143AA.

This table covers the gaskets that seal the Differential Cover. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

One part is listed for the 2010 Chrysler 300 — ELRING B12900.

This table covers the Differential Crush sleeves. Read more

This group shows a single part: USA STANDARD GEAR USA33128.

This table covers the Differential mounts. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes. Read more

4 Differential Mount parts for the 2010 Chrysler 300 come from MOPAR. 2 parts fit every engine; the other 2 are engine-specific.

Listed part numbers: MOPAR 4578191AA, MOPAR 4578084AC and MOPAR 4578085AA, plus the other parts above.

This table covers the slingers that keep gear oil off the pinion seal. Read more

One part is listed for the 2010 Chrysler 300 — USA STANDARD GEAR USA33008.

This table covers the bearings and races on the differential pinion. Read more

42 Differential Pinion Bearing / Race parts for the 2010 Chrysler 300 come from 8 brands — BCA, WJB / INMOTION PARTS, FAMOUS BRAND and 5 other brands. The "Popular" part is FAMOUS BRAND SM86610. They are grouped as Economy and Standard Replacement, with Standard Replacement the largest group at 26 parts from BCA, NATIONAL, SKF and 2 other brands.

This table covers the baffles that control oil at the pinion bearings. Read more

This group shows a single part: RICHMOND 0400152.

This table covers the flanges that connect the driveshaft to the differential pinion. Read more

3 Differential Pinion Flange parts are listed for the 2010 Chrysler 300, from DORMAN and MOPAR.

Listed part numbers: DORMAN 697631, DORMAN 697630 and MOPAR 52852996AA.

This table covers the Differential Pinion nuts. Read more

One part is listed for the 2010 Chrysler 300 — USA STANDARD GEAR USA33170.

This table covers the wear sleeves used to restore a grooved pinion seal surface. Read more

2 Differential Pinion Repair Sleeve parts are listed for the 2010 Chrysler 300, from BCA and WJB / INMOTION PARTS.

This group includes BCA NS99139 and WJB / INMOTION PARTS WS99139.

This table covers the seals at the differential pinion yoke. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

7 Differential Pinion Seal parts are listed for the 2010 Chrysler 300, from WJB / INMOTION PARTS and NATIONAL. NATIONAL 711055 carries the "Popular" badge. 6 parts fit every engine; the other 1 is engine-specific.

Listed part numbers: NATIONAL 711055, NATIONAL 710998 and NATIONAL 710996, plus the other parts above.

This table covers the Differential Pinion shims. Read more

MOPAR supplies the 5 Differential Pinion Shim parts for the 2010 Chrysler 300. All of them fit every engine offered in the 2010 300.

This group includes MOPAR 5139419AA, MOPAR 5139421AA and MOPAR 5139429AA and the remaining parts above.

This table covers kits that group the bearings, races and seals for a differential rebuild. Read more

This group shows a single part: TIMKEN DRK370.

This table covers the ring-and-pinion gear sets that set the axle ratio. Read more

RICHMOND supplies both parts for the 2010 Chrysler 300. 1 part fits every engine; the other 1 is engine-specific.

This group includes RICHMOND 4901641 and RICHMOND 4901531.

This table covers the Differential Ring Gear bolts. Read more

One part is listed for the 2010 Chrysler 300 — USA STANDARD GEAR USA33069.

This table covers the seals at the Differential. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

3 Differential Seal parts for the 2010 Chrysler 300 come from 3 brands — MOPAR, NATIONAL and WJB / INMOTION PARTS. Every part fits all 4 engine options (2.7L V6, 3.5L V6, 5.7L V8 and 6.1L V8).

Listed part numbers: MOPAR 5161591AA, NATIONAL 711050 and WJB / INMOTION PARTS WS711050.

This table covers the driveshafts that carry torque from the transmission or transfer case. Read more

19 Drive Shaft parts for the 2010 Chrysler 300 come from 9 brands — DORMAN, MOPAR, TOP NOTCH and 6 other brands. The "Popular" part is SKP SK936400. 1 part fits every engine; the other 18 are engine-specific.