2016 Ford Fusion Engine Parts

This table covers the chains that drive the balance shafts. Read more

INA supplies both parts for the 2016 Ford Fusion.

The Chain Only section lists 1 option from INA — grouped under the catalog's "Chain Only" designation — the notes column spells out what sets them apart. INA ZCC718F is listed in this group.

In the Kit grade, INA supplies 1 part: grouped under the catalog's "Kit" designation — the notes column spells out what sets them apart. A representative part number is INA ZC76350P.

Listed part numbers: INA ZCC718F and INA ZC76350P.

This table covers the Balance Shaft sprockets. Read more

One part is listed for the 2016 Ford Fusion — INA ZSS983.

This table covers the wear sleeves used to restore a Camshaft seal surface. Read more

3 Camshaft Repair Sleeve parts for the 2016 Ford Fusion come from 3 brands — MOTIVE GEAR, NATIONAL and WJB / INMOTION PARTS.

This group includes MOTIVE GEAR MGMS4271805, NATIONAL 99181 and WJB / INMOTION PARTS WS99181.

This table covers the seals at each camshaft end. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

8 Camshaft Seal parts for the 2016 Ford Fusion come from 6 brands — NATIONAL, MAHLE / CLEVITE, FEL-PRO and 3 other brands. The "Popular" part is FEL-PRO TCS46179.

Listed part numbers: FEL-PRO TCS46179, NATIONAL 711002 and APEX ATC13320, plus the other parts above.

This table covers the bearings in the connecting-rod big ends. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

12 Connecting Rod Bearing parts are listed for the 2016 Ford Fusion, from MAHLE / CLEVITE, TOPLINE, KING ENGINE BEARINGS and 3 other brands. MAHLE / CLEVITE CB1840A4 carries the "Popular" badge.

In the High Performance grade, KING ENGINE BEARINGS supplies 1 part: engineered beyond original-equipment specification. A representative part number is KING ENGINE BEARINGS CR4604XP.

The Standard Replacement section lists 4 options from MAHLE / CLEVITE, ITM ENGINE COMPONENTS and KING ENGINE BEARINGS — built to original-equipment specification. MAHLE / CLEVITE CB1840A4 is listed in this group.

7 ungrouped parts are not assigned to a grade, with the same engine-level match.

This table covers lower / conversion gasket sets for oil-pan and related joints. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

17 Conversion / Lower Gasket Set parts are listed for the 2016 Ford Fusion, from APEX, FEL-PRO, AJUSA and 5 other brands. APEX ACS4080 carries the "Popular" badge.

This table covers the main bearings that support the crankshaft in the block. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

11 Crankshaft Main Bearing parts for the 2016 Ford Fusion come from 5 brands — KING ENGINE BEARINGS, ENGINETECH, MAHLE / CLEVITE and 2 other brands. The "Popular" part is ENGINETECH BC116J.

The High Performance section: 2 options from KING ENGINE BEARINGS. KING ENGINE BEARINGS MB5442XP is listed in this group.

Standard Replacement: 3 parts, from ENGINETECH, KING ENGINE BEARINGS and MAHLE / CLEVITE. A representative part number is ENGINETECH BC116J.

6 further parts sit outside the graded sections, with the same engine-level match.

This table covers the sleeves used to restore a grooved crankshaft seal surface. Read more

4 Crankshaft Repair Sleeve parts for the 2016 Ford Fusion come from 4 brands — BCA, NATIONAL, TIMKEN and 1 other brand.

Listed part numbers: BCA NS99145, NATIONAL 99145 and TIMKEN KWK99145, plus the other parts above.

This table covers the front and rear seals that keep oil in at the crankshaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

32 Crankshaft Seal parts for the 2016 Ford Fusion come from 12 brands — FEL-PRO, APEX, NATIONAL and 9 other brands. The "Popular" part is FEL-PRO BS40747. A list this long means Crankshaft Seal applications vary by configuration — the notes carry the qualifiers.

This table covers the Crankshaft Seal covers. Read more

One part is listed for the 2016 Ford Fusion — DORMAN 635557.

This table covers the cylinder heads that close the top of the block. Read more

This group shows a single part: CYLINDER HEAD EXPRESS FO1510N.

This table covers the bolts that clamp the cylinder head to the block. Read more

13 Cylinder Head Bolt parts are listed for the 2016 Ford Fusion, from AJUSA, FEL-PRO, APEX and 4 other brands. AJUSA 81017400 carries the "Popular" badge.

This table covers the head gaskets that seal the block to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

16 Cylinder Head Gasket parts are listed for the 2016 Ford Fusion, from FEL-PRO, ULTRA-POWER, APEX and 3 other brands. FEL-PRO 26750PT carries the "Popular" badge.

This table covers multi-piece gasket sets for a cylinder-head job. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

15 Cylinder Head Gasket Set parts are listed for the 2016 Ford Fusion, from AJUSA, MAHLE / CLEVITE, FEL-PRO and 7 other brands. FEL-PRO HS26521PT carries the "Popular" badge.

This table covers the Cylinder Head temperature sensors. Typical signs include hard cold starts, a fan that never comes on, or a gauge that disagrees with the scan tool. A sensor that reads open or shorted is usually the part; an implausible-but-smooth reading can be wiring. Read more

8 Cylinder Head Temperature Sensor parts for the 2016 Ford Fusion come from 5 brands — DORMAN, NTK, WELLS and 2 other brands. The "Popular" part is STANDARD MOTOR PRODUCTS TS640.

Listed part numbers: STANDARD MOTOR PRODUCTS TS640, DORMAN 926711 and DORMAN 926709, plus the other parts above.

This table covers the block heaters that warm the coolant or oil in cold weather. Read more

4 Engine Block Heater parts for the 2016 Ford Fusion come from 2 brands — KAT'S HEATERS and MOTORAD.

This group includes KAT'S HEATERS 28400, KAT'S HEATERS 11488 and KAT'S HEATERS 11409 and the remaining parts above.

This table covers the Engine covers. Read more

7 Engine Cover parts are listed for the 2016 Ford Fusion, from TECHPRO and VARIOUS MFR. TECHPRO FO1228124 carries the "Popular" badge.

This group includes TECHPRO FO1228124, TECHPRO FO1228126 and TECHPRO FO1228153 and the remaining parts above.

This table covers the Engine Cover grommets. Read more

This group shows a single part: DORMAN 49931.

This table covers full gasket kits covering the joints opened in an engine rebuild. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

5 Engine Kit Gasket Set parts are listed for the 2016 Ford Fusion, from AJUSA and TOPLINE.

This group includes AJUSA 50407600, AJUSA 50409000 and AJUSA 50475300 and the remaining parts above.

This table covers the exhaust valves that let combustion gas out of the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

10 Exhaust Valve parts for the 2016 Ford Fusion come from 6 brands — ENGINETECH, QUALCAST, SBI and 3 other brands. The "Popular" part is ENGINETECH V4383.

This table covers the followers that drive a mechanical fuel pump off the camshaft. Read more

One part is listed for the 2016 Ford Fusion — STANDARD MOTOR PRODUCTS GDF201.

This table covers the crankshaft pulleys / harmonic balancers at the front of the engine. Read more

5 Harmonic Balancer parts are listed for the 2016 Ford Fusion, from ATP and DORMAN.

Listed part numbers: ATP 102463, ATP 102450 and ATP 102411, plus the other parts above.

This table covers the Harmonic Balancer bolts. Read more

3 Harmonic Balancer Bolt parts for the 2016 Ford Fusion come from 3 brands — DORMAN, SKP and ULTRA-POWER.

Part numbers include DORMAN 926885 and SKP SK926885, among others listed above.

This table covers the Intake manifolds. Typical signs include an exhaust tick, a vacuum leak, or a gasket that has burned through. Replace the gaskets and hardware; a warped flange will leak with a new gasket alone. Read more

This group shows a single part: VAICO V252268.

This table covers the gaskets between the intake manifold and the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

15 Intake Manifold Gasket parts are listed for the 2016 Ford Fusion, from MAHLE / CLEVITE, FEL-PRO, APEX and 4 other brands. FEL-PRO MS97419 carries the "Popular" badge.

This table covers the intake valves that let air (and fuel, on port-injected engines) into the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

10 Intake Valve parts for the 2016 Ford Fusion come from 6 brands — ENGINETECH, QUALCAST, SBI and 3 other brands. The "Popular" part is ENGINETECH V4382.

This table covers the mounts that hold the engine to the chassis. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes. Read more

15 Motor Mount parts for the 2016 Ford Fusion come from 5 brands — ANCHOR, WESTAR, DEA / MARMON RIDE CONTROL and 2 other brands. The "Popular" part is ANCHOR 3348.

The Economy section lists 1 option from SKP — the catalog's value-priced group. SKP SKM3347 is listed in this group.

Standard Replacement: 4 parts, from ANCHOR, DEA / MARMON RIDE CONTROL, PIONEER and 1 other brand. A representative part number is ANCHOR 3348.

10 further parts sit outside the graded sections, with the same engine-level match.

This table covers the Motor Mount kits. Read more

4 Motor Mount Kit parts for the 2016 Ford Fusion come from ANCHOR.

Listed part numbers: ANCHOR 300531, ANCHOR 300154 and ANCHOR 301031, plus the other parts above.