1990 Honda Prelude Engine Parts

This table covers the wear sleeves used to restore a Camshaft seal surface. Read more

This group shows a single part: SCHAEFFLER SR3460.

This table covers the seals at each camshaft end. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

26 Camshaft Seal parts for the 1990 Honda Prelude come from 13 brands — APEX, FEL-PRO, MAHLE / CLEVITE and 10 other brands. The "Popular" part is CONTINENTAL CS11429. A list this long means Camshaft Seal applications vary by configuration — the notes carry the qualifiers.

This table covers the connecting rods between each piston and the crankshaft. Read more

TOPLINE supplies both parts for the 1990 Honda Prelude.

This group includes TOPLINE CRH23 and TOPLINE CRH19.

This table covers the bearings in the connecting-rod big ends. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

18 Connecting Rod Bearing parts are listed for the 1990 Honda Prelude, from KING ENGINE BEARINGS, MAHLE / CLEVITE, SEALED POWER and 3 other brands. KING ENGINE BEARINGS CR439XP carries the "Popular" badge.

In the High Performance grade, KING ENGINE BEARINGS and MAHLE / CLEVITE supply 7 parts: engineered beyond original-equipment specification. A representative part number is KING ENGINE BEARINGS CR439XP.

The Standard Replacement section lists 11 options from SEALED POWER, KING ENGINE BEARINGS, MAHLE / CLEVITE and 3 other brands — built to original-equipment specification. ENGINETECH BB1520 is listed in this group.

This table covers lower / conversion gasket sets for oil-pan and related joints. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

7 Conversion / Lower Gasket Set parts are listed for the 1990 Honda Prelude, from APEX, AJUSA, FEL-PRO and 3 other brands. APEX ACS1012 carries the "Popular" badge. 3 parts fit every engine; the other 4 are engine-specific.

Part numbers include APEX ACS1012, AJUSA 54068900 and APEX ACS1009, among others listed above.

This table covers the main bearings that support the crankshaft in the block. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

10 Crankshaft Main Bearing parts for the 1990 Honda Prelude come from 6 brands — MAHLE / CLEVITE, KING ENGINE BEARINGS, TOPLINE and 3 other brands. The "Popular" part is KING ENGINE BEARINGS MB5568AM. Every part fits both the 2.0L L4 DOHC and the 2.0L L4 SOHC.

The High Performance section: 2 options from KING ENGINE BEARINGS and MAHLE / CLEVITE. KING ENGINE BEARINGS MB5568XP is listed in this group.

Standard Replacement: 8 parts, from MAHLE / CLEVITE, TOPLINE, KING ENGINE BEARINGS and 3 other brands. A representative part number is KING ENGINE BEARINGS MB5568AM.

This table covers the sleeves used to restore a grooved crankshaft seal surface. Read more

7 Crankshaft Repair Sleeve parts for the 1990 Honda Prelude come from 6 brands — TIMKEN, BCA, FEL-PRO and 3 other brands. The "Popular" part is BCA NS99315. Every part fits both the 2.0L L4 DOHC and the 2.0L L4 SOHC.

Part numbers include BCA NS99315, TIMKEN KWK99147 and FEL-PRO 16275, among others listed above.

This table covers the front and rear seals that keep oil in at the crankshaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

20 Crankshaft Seal parts for the 1990 Honda Prelude come from 13 brands — APEX, FEL-PRO, VICTOR REINZ and 10 other brands. The "Popular" part is APEX ABS100. 15 parts fit every engine; the other 5 are engine-specific.

This table covers the head gaskets that seal the block to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

6 Cylinder Head Gasket parts are listed for the 1990 Honda Prelude, from FEL-PRO, APEX, ELRING and 3 other brands. FEL-PRO 9124PT1 carries the "Popular" badge. 4 parts fit every engine; the other 2 are engine-specific.

Listed part numbers: FEL-PRO 9124PT1, APEX AHG109 and ELRING 704620, plus the other parts above.

This table covers multi-piece gasket sets for a cylinder-head job. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

12 Cylinder Head Gasket Set parts are listed for the 1990 Honda Prelude, from APEX, ENGINETECH, ITM ENGINE COMPONENTS and 5 other brands. APEX AHS1012 carries the "Popular" badge.

This table covers the wear sleeves used to restore a Cylinder seal surface. Read more

MELLING supplies both parts for the 1990 Honda Prelude. All of them fit every engine offered in the 1990 Prelude.

Part numbers include MELLING CSL105 and MELLING CSL205.

This table covers full gasket kits covering the joints opened in an engine rebuild. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

8 Engine Kit Gasket Set parts are listed for the 1990 Honda Prelude, from AJUSA, APEX, ITM ENGINE COMPONENTS and 1 other brand.

This group includes AJUSA 50142900, AJUSA 50131100 and APEX AFS1012 and the remaining parts above.

This table covers the exhaust valves that let combustion gas out of the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

12 Exhaust Valve parts for the 1990 Honda Prelude come from 7 brands — TOPLINE, ENGINETECH, ITM ENGINE COMPONENTS and 4 other brands. The "Popular" part is ENGINETECH EM2533. 2 parts fit every engine; the other 10 are engine-specific.

This table covers the Expansion plugs. Typical signs include a leak at the drain or glow-plug hole, or a plug that has rounded off. Replace the crush washer and torque to the spec in the notes. Read more

4 Expansion Plug parts are listed for the 1990 Honda Prelude, from MELLING and QUALCAST. All of them fit every engine offered in the 1990 Prelude.

Listed part numbers: MELLING MPE189R, MELLING MPE189BR and QUALCAST 97110B, plus the other parts above.

This table covers the gaskets between the intake manifold and the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

7 Intake Manifold Gasket parts are listed for the 1990 Honda Prelude, from AJUSA, ITM ENGINE COMPONENTS, FEL-PRO and 2 other brands. FEL-PRO MS94121 carries the "Popular" badge. 2 parts fit every engine; the other 5 are engine-specific.

This group includes FEL-PRO MS94121, AJUSA 13110500 and AJUSA 13097400 and the remaining parts above.

This table covers the intake valves that let air (and fuel, on port-injected engines) into the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

9 Intake Valve parts for the 1990 Honda Prelude come from 6 brands — ENGINETECH, ITM ENGINE COMPONENTS, QUALCAST and 3 other brands. The "Popular" part is ENGINETECH IM2454. 2 parts fit every engine; the other 7 are engine-specific.

Part numbers include ENGINETECH IM2454, MELLING V5192 and SBI 10195, among others listed above.

This table covers the mounts that hold the engine to the chassis. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes. Read more

12 Motor Mount parts for the 1990 Honda Prelude come from 4 brands — WESTAR, ANCHOR, DEA / MARMON RIDE CONTROL and 1 other brand. The "Popular" part is ANCHOR 8030. Every part fits both the 2.0L L4 DOHC and the 2.0L L4 SOHC.

This table covers the engine oils listed by grade and specification for this engine. Typical signs include a low-oil lamp, knocking after a long interval, or oil that has gone thin and black well before the next service. Match the viscosity and spec in the notes (and on the filler cap). The tables group grades — they are not interchangeable. Read more

21 Oil parts for the 1990 Honda Prelude come from 3 brands — MOBIL, VALVOLINE and IDEMITSU. The "Popular" part is MOBIL 125195. Every part fits both the 2.0L L4 DOHC and the 2.0L L4 SOHC.

The Full Synthetic section lists 7 options from MOBIL and VALVOLINE — full-synthetic oils. MOBIL 125195 is listed in this group.

In the High Mileage (>75,000 Miles) grade, VALVOLINE and MOBIL supply 8 parts: oils grouped for high-mileage engines. A representative part number is VALVOLINE VV1556.

The Racing section lists 2 options from IDEMITSU — grouped under the catalog's "Racing" designation — the notes column spells out what sets them apart. IDEMITSU 30018100750 is listed in this group.

The Synthetic Blend section lists 4 options from MOBIL and VALVOLINE — synthetic-blend oils. MOBIL 124406 is listed in this group.

This table covers the Oil Cooler Mounting kits. Read more

HAYDEN supplies both parts for the 1990 Honda Prelude. All of them fit every engine offered in the 1990 Prelude.

Listed part numbers: HAYDEN 238 and HAYDEN 153.

This table covers the drain plugs in the oil pan. Read more

11 Oil Drain Plug parts for the 1990 Honda Prelude come from 5 brands — DORMAN, ELRING, AGS and 2 other brands. The "Popular" part is AGS ODP00007. 9 parts fit every engine; the other 2 are engine-specific.

In the Piggyback grade, DORMAN supplies 1 part: grouped under the catalog's "Piggyback" designation — the notes column spells out what sets them apart. A representative part number is DORMAN 65229.

In the Twist Drain grade, DORMAN supplies 1 part: grouped under the catalog's "Twist Drain" designation — the notes column spells out what sets them apart. A representative part number is DORMAN 092020.

In the Universal grade, DORMAN supplies 1 part: grouped under the catalog's "Universal" designation — the notes column spells out what sets them apart. A representative part number is DORMAN 65102.

8 further parts sit outside the graded sections, with the same engine-level match.

This table covers the crush washers and gaskets under the oil drain plug. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

5 Oil Drain Plug Gasket parts are listed for the 1990 Honda Prelude, from ULTRA-POWER, DORMAN, AJUSA and 1 other brand. DORMAN 095144 carries the "Popular" badge. 4 parts fit every engine; the other 1 is engine-specific.

Part numbers include DORMAN 095144, AJUSA 22007400 and ELRING 243600, among others listed above.

This table covers the caps on the oil filler neck. Read more

4 Oil Filler Cap parts for the 1990 Honda Prelude come from 4 brands — BECK/ARNLEY, GATES, MOTORAD and 1 other brand. Every part fits both the 2.0L L4 DOHC and the 2.0L L4 SOHC.

Listed part numbers: BECK/ARNLEY 0160125, GATES 31109 and MOTORAD MO81, plus the other parts above.

This table covers the oil filters that screw onto this engine's filter mount. Typical signs include low oil pressure after a service, or a filter that will not spin off because the old gasket stayed on the block. Lube the new gasket and tighten to the spec on the box; a double-gasket install dumps the sump on the first drive. Read more

18 Oil Filter parts for the 1990 Honda Prelude come from 14 brands — VARIOUS MFR, BOSCH, WIX and 11 other brands. The "Popular" part is WIX 51334XP. 17 parts fit every engine; the other 1 is engine-specific.

The Economy section lists 6 options from VARIOUS MFR, BOSCH, FRAM and 2 other brands — the catalog's value-priced group. BOSCH 72228WS is listed in this group.

The High Performance / Heavy Duty section lists 2 options from WIX and MOBIL — grouped under the catalog's "High Performance / Heavy Duty" designation — the notes column spells out what sets them apart. WIX 51334XP is listed in this group.

Standard Replacement: 10 parts, from BOSCH, DENSO, WIX and 7 other brands. A representative part number is BOSCH 3312.

This table covers the Oil Filter Support tubes. Read more

One part is listed for the 1990 Honda Prelude — AUTOTECNICA HA1416938.

This table covers the gaskets between the oil pan and the block. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

4 Oil Pan Gasket parts for the 1990 Honda Prelude come from 4 brands — APEX, FEL-PRO, ITM ENGINE COMPONENTS and 1 other brand. 3 parts fit every engine; the other 1 is engine-specific.

Part numbers include APEX AOP109, FEL-PRO OS30598R and ITM ENGINE COMPONENTS 0990917, among others listed above.

This table covers the pistons that travel in each cylinder. Typical signs include knock, blow-by, or a cylinder that will not hold compression. Piston work is a short-block job. Match bore, pin and ring pack in the notes — not the photo. Read more

4 Piston parts are listed for the 1990 Honda Prelude, from ITM ENGINE COMPONENTS and TOPLINE.

Part numbers include ITM ENGINE COMPONENTS RY6399, ITM ENGINE COMPONENTS RY6398 and TOPLINE PAH19L, among others listed above.

This table covers the rings that seal each piston to the cylinder wall. Read more

5 Piston Ring parts are listed for the 1990 Honda Prelude, from HASTINGS MANUFACTURING, ITM ENGINE COMPONENTS and TOPLINE. HASTINGS MANUFACTURING 2C4684 carries the "Popular" badge. All of them fit every engine offered in the 1990 Prelude.

Listed part numbers: HASTINGS MANUFACTURING 2C4684, HASTINGS MANUFACTURING 2C4684S and HASTINGS MANUFACTURING 2C4658, plus the other parts above.

This table covers the rocker arms that transfer cam motion to the valves. Read more

3 Rocker Arm parts for the 1990 Honda Prelude come from TOPLINE.

This group includes TOPLINE RAH19, TOPLINE RAH15A and TOPLINE RAH15B.

This table covers the Thrust washers. Read more

6 Thrust Washer parts for the 1990 Honda Prelude come from 6 brands — ENGINETECH, MAHLE / CLEVITE, ENGINE PRO and 3 other brands. The "Popular" part is ENGINETECH TW1516. Every part fits both the 2.0L L4 DOHC and the 2.0L L4 SOHC.

Part numbers include ENGINETECH TW1516, MAHLE / CLEVITE TW473S and ENGINE PRO 13473S, among others listed above.

This table covers the Timing belts. Typical signs include squeal on cold start, cracked ribs, or glazing. Spin the tensioner and idlers by hand while the belt is off. Read more

17 Timing Belt parts are listed for the 1990 Honda Prelude, from GATES, CONTINENTAL, ITM ENGINE COMPONENTS and 8 other brands. CLOYES B144 carries the "Popular" badge.

Economy: 6 parts, from ITM ENGINE COMPONENTS, CLOYES, CADNA and 2 other brands. A representative part number is CLOYES B144.

High Performance: 1 part, from GATES. A representative part number is GATES T142RB.

The Standard Replacement section: 10 options from GATES, BANDO, TOPLINE and 4 other brands. GATES T142 is listed in this group.