2007 Jeep Commander Automatic Transmission Parts

This table covers the pistons inside a transmission accumulator. Read more

4 Accumulator Piston parts are listed for the 2007 Jeep Commander, from SONNAX, MOPAR and TRANSGO. 3 parts fit every engine; the other 1 is engine-specific.

Part numbers include MOPAR 4446620AD, SONNAX 4489401K and SONNAX 4489401MK, among others listed above.

This table covers the Accumulator springs. Typical signs include a sagging corner, a broken coil, or a clunk from the spring pocket. Replace springs in axle pairs and inspect the seats. Read more

MOPAR supplies both parts for the 2007 Jeep Commander.

Part numbers include MOPAR 52119702AA and MOPAR 4471880.

This table covers the control units that command automatic-transmission shifts. Read more

One part is listed for the 2007 Jeep Commander — MOPAR 5150186AH.

This table covers the bushings in this assembly. Typical signs include a clunk over bumps, or a torn or walked-out bushing you can see. Press the new bushing square. A cocked bushing will tear in a few thousand miles. Read more

This group shows a single part: DURA-BOND DOT11BRTG.

This table covers the Bushing kits. Read more

2 Bushing Kit parts for the 2007 Jeep Commander come from 2 brands — DURA-BOND and PA CARGO.

This group includes DURA-BOND TK9A and PA CARGO K44901.

This table covers the transmission or transfer-case housings. Read more

This group shows a single part: MOPAR 5189883AC.

This table covers the Case covers. Read more

MOPAR supplies both parts for the 2007 Jeep Commander. 1 part fits every engine; the other 1 is engine-specific.

Part numbers include MOPAR 52104344AA and MOPAR 53013573AB.

This table covers the vents on a transmission or axle housing. Read more

One part is listed for the 2007 Jeep Commander — MOPAR 52104552AC.

This table covers the Clutch housings. Read more

This group shows a single part: SONNAX 7296006K.

This table covers the pistons that apply a clutch pack. Read more

MOPAR supplies both parts for the 2007 Jeep Commander.

Part numbers include MOPAR 4799650 and MOPAR 4799652.

This table covers the Clutch plates. Typical signs include warpage, cracks, or a plate that no longer locates the assembly. Confirm which plate the notes describe — backing plates, clutch plates and strike plates are different parts. Read more

One part is listed for the 2007 Jeep Commander — MOPAR 4799116.

This table covers the clutch-plate packs inside the transmission or transfer case. Read more

2 Clutch Plate Pack parts for the 2007 Jeep Commander come from RAYBESTOS POWERTRAIN.

Part numbers include RAYBESTOS POWERTRAIN RCP96105 and RAYBESTOS POWERTRAIN RGPZ105.

This table covers the related components grouped with this assembly. Read more

3 Components parts for the 2007 Jeep Commander come from SONNAX.

Listed part numbers: SONNAX 4491202, SONNAX RFERC1 and SONNAX 4483602K.

This table covers the Conductor plates. Typical signs include warpage, cracks, or a plate that no longer locates the assembly. Confirm which plate the notes describe — backing plates, clutch plates and strike plates are different parts. Read more

14 Conductor Plate parts are listed for the 2007 Jeep Commander, from ULTRA-POWER, SKP, DORMAN and 4 other brands. SKP SK917678 carries the "Popular" badge.

In the Economy grade, SKP, ULTRA-POWER, DORMAN and 1 other brand supply 6 parts: the catalog's value-priced group. A representative part number is SKP SK917678.

The Standard Replacement section lists 3 options from STANDARD MOTOR PRODUCTS, NTK and ROSTRA — built to original-equipment specification. STANDARD MOTOR PRODUCTS TCP01 is listed in this group.

5 ungrouped parts are not assigned to a grade, with the same engine-level match.

This table covers the Dipstick / Fluid Filler tubes. Read more

2 Dipstick / Fluid Filler Tube parts for the 2007 Jeep Commander come from 2 brands — DORMAN and MOPAR.

Part numbers include DORMAN 917327 and MOPAR 5037752AC.

This table covers the seals at the Dipstick / Fluid Filler Tube. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

One part is listed for the 2007 Jeep Commander — PIONEER 760034.

This table covers the Extension Housing bearings. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

3 Extension Housing Bearing parts for the 2007 Jeep Commander come from 3 brands — BCA, NATIONAL and WJB / INMOTION PARTS. Every part fits all 3 engine options (3.7L V6, 4.7L V8 and 5.7L V8).

Listed part numbers: BCA NB110, NATIONAL 110 and WJB / INMOTION PARTS RB6010.

This table covers the Extension Housing bushings. Typical signs include a clunk over bumps, or a torn or walked-out bushing you can see. Press the new bushing square. A cocked bushing will tear in a few thousand miles. Read more

This group shows a single part: DURA-BOND RP6189T.

This table covers the seals at the Extension Housing. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

14 Extension Housing Seal parts are listed for the 2007 Jeep Commander, from WJB / INMOTION PARTS, NATIONAL, ATP and 2 other brands. ATP FO199 carries the "Popular" badge. 13 parts fit every engine; the other 1 is engine-specific.

This table covers the replacement filters for this application — the table heading and notes say which circuit. Typical signs include restricted flow — long cranking, weak airflow, or dirty fluid after a short interval. Seat the new filter so it cannot bypass, and use the grade the notes call for. Read more

45 Filter parts for the 2007 Jeep Commander come from 14 brands — ATP, VAICO, VARIOUS MFR and 11 other brands. The "Popular" part is ACDELCO TF357. Basic Kit (Without Transmission Fluid), Economy and Standard Replacement are all represented, and Standard Replacement alone accounts for 25 parts.

This table covers the flexplates that connect the crankshaft to the torque converter. Read more

4 Flexplate parts are listed for the 2007 Jeep Commander, from ATP and PIONEER.

Part numbers include ATP Z628, ATP Z606 and PIONEER FRA553, among others listed above.

This table covers the Flexplate Mounting bolts. Read more

One part is listed for the 2007 Jeep Commander — DORMAN 14131.

This table covers the Fluid Cooler Line hoses. Typical signs include swelling, cracks, a soft spot, or a leak at a clamp. Replace adjacent aged hoses while the system is drained — they share the same heat cycle. Read more

5 Fluid Cooler Line / Hose parts for the 2007 Jeep Commander come from 2 brands — DORMAN and SUNSONG.

This group includes DORMAN 624281, DORMAN 624992 and DORMAN 724992 and the remaining parts above.

This table covers the harness connectors at the Fluid Cooler Line / Hose. Typical signs include an intermittent fault that moves when you wiggle the plug, green corrosion, or a melted housing. Match terminal count and keyway, not just color. Many families look identical and will not lock. Read more

One part is listed for the 2007 Jeep Commander — DORMAN 800723.

This table covers the pans that hold automatic-transmission fluid. Read more

11 Fluid Pan parts are listed for the 2007 Jeep Commander, from DORMAN, SKP, MOPAR and 4 other brands. DORMAN 265817 carries the "Popular" badge. 7 parts fit every engine; the other 4 are engine-specific.

This table covers the Fluid Pan drain plugs. Read more

One part is listed for the 2007 Jeep Commander — DORMAN 265002.

This table covers the gaskets that seal the Fluid Pan. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

8 Fluid Pan Gasket parts for the 2007 Jeep Commander come from 6 brands — FEL-PRO, MAHLE / CLEVITE, ATP and 3 other brands. The "Popular" part is ATP TG110. 4 parts fit every engine; the other 4 are engine-specific.

Listed part numbers: ATP TG110, FEL-PRO TOS18733 and TRANSTEC 49444827, plus the other parts above.

This table covers the Fluid Pan magnets. Read more

MOPAR supplies both parts for the 2007 Jeep Commander. 1 part fits every engine; the other 1 is engine-specific.

Listed part numbers: MOPAR 68207788AA and MOPAR 68207789AA.

This table covers the Fluid pressure sensors. Typical signs include a check-engine light for MAP or fuel-rail pressure, or a limp mode under load. A vacuum leak or a clogged reference line will fake a bad pressure sensor. Read more

8 Fluid Pressure Sensor parts are listed for the 2007 Jeep Commander, from MOPAR, WELLS, ATP and 5 other brands. MOPAR 4799758AD carries the "Popular" badge. 5 parts fit every engine; the other 3 are engine-specific.

This group includes MOPAR 4799758AD, WELLS 5S5389 and ATP TE18 and the remaining parts above.

This table covers the Fluid pumps. Typical signs include noise from the pump, no pressure, or fluid that never arrives at the outlet. Prime or fill the pump as the notes require. A dry start is a common way to kill a new unit. Read more

6 Fluid Pump parts for the 2007 Jeep Commander come from MOPAR. 2 parts fit every engine; the other 4 are engine-specific.

This group includes MOPAR 5080070AB, MOPAR R8087860AA and MOPAR RL087860AA and the remaining parts above.

This table covers the precision wear sleeves used to restore a transmission pump seal surface. Read more

3 Fluid Pump Repair Sleeve parts are listed for the 2007 Jeep Commander, from BCA, NATIONAL and WJB / INMOTION PARTS. All of them fit every engine offered in the 2007 Commander.

Part numbers include BCA NS88187, NATIONAL 99187 and WJB / INMOTION PARTS WS99187.

This table covers the seals at the Fluid Pump. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

9 Fluid Pump Seal parts are listed for the 2007 Jeep Commander, from NATIONAL, BCA, WJB / INMOTION PARTS and 3 other brands. NATIONAL 710557 carries the "Popular" badge. 6 parts fit every engine; the other 3 are engine-specific.

This group includes NATIONAL 710557, NATIONAL 710608 and BCA NS710557 and the remaining parts above.

This table covers the Fluid temperature sensors. Typical signs include hard cold starts, a fan that never comes on, or a gauge that disagrees with the scan tool. A sensor that reads open or shorted is usually the part; an implausible-but-smooth reading can be wiring. Read more

This group shows a single part: MOPAR 5149008AA.

This table covers the gasket kits for this job. Typical signs include the leaks that sent this assembly to the bench. Confirm the kit matches the opening you are sealing; unused leftover pieces often belong to another configuration. Read more

One part is listed for the 2007 Jeep Commander — VICTOR REINZ 711917000.

This table covers the governors and modulators that control transmission shift pressure. Read more

2 Governor / Modulator parts for the 2007 Jeep Commander come from 2 brands — DORMAN and SONNAX. Every part fits all 3 engine options (3.7L V6, 4.7L V8 and 5.7L V8).

Listed part numbers: DORMAN 601215 and SONNAX RFELB1.

This table covers the Input shafts. Read more

2 Input Shaft parts for the 2007 Jeep Commander come from MOPAR. 1 part fits every engine; the other 1 is engine-specific.

Listed part numbers: MOPAR 52108044AA and MOPAR 5114582AA.

This table covers the seals at the Manual Shaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

4 Manual Shaft Seal parts are listed for the 2007 Jeep Commander, from NATIONAL and WJB / INMOTION PARTS. All of them fit every engine offered in the 2007 Commander.

Listed part numbers: NATIONAL 710753, NATIONAL 711035 and WJB / INMOTION PARTS WS710753, plus the other parts above.

This table covers the Output Shaft bearings. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

4 Output Shaft Bearing parts are listed for the 2007 Jeep Commander, from WJB / INMOTION PARTS, BCA and NATIONAL.

Economy: 1 part, from WJB / INMOTION PARTS. A representative part number is WJB / INMOTION PARTS RB6206.

The Standard Replacement section: 2 options from BCA and NATIONAL. BCA NB206 is listed in this group.

1 ungrouped part is not assigned to a grade, with the same engine-level match.

This group includes WJB / INMOTION PARTS RB6206, BCA NB206 and NATIONAL 206 and the remaining parts above.

This table covers the seals at the Output Shaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

2 Output Shaft Seal parts for the 2007 Jeep Commander come from 2 brands — ACDELCO and SCHAEFFLER. Every part fits all 3 engine options (3.7L V6, 4.7L V8 and 5.7L V8).

This group includes ACDELCO 7300S and SCHAEFFLER SS2723.

This table covers the parking pawls that lock the transmission in Park. Read more

This group shows a single part: MOPAR 52108154AA.

This table covers the Plug adapters. Read more

3 Plug Adapter parts are listed for the 2007 Jeep Commander, from DORMAN, ROSTRA and STANDARD MOTOR PRODUCTS. 1 part fits every engine; the other 2 are engine-specific.

Part numbers include DORMAN 917505, ROSTRA 3500175 and STANDARD MOTOR PRODUCTS TCPA01.

This table covers the Pressure Control (EPC) solenoids. Typical signs include a harsh or missing shift, or a code for this solenoid circuit. Check resistance and the connector before dropping the pan for a solenoid. Read more

This group shows a single part: WELLS 2N1281.

This table covers the rebuild kits for this assembly. Read more

12 Rebuild Kit parts are listed for the 2007 Jeep Commander, from PA CARGO, PIONEER, TRANSTEC and 1 other brand. PA CARGO DK4400BS carries the "Popular" badge. 10 parts fit every engine; the other 2 are engine-specific.

In the Banner Kit (Overhaul Kit + Friction Clutch Plates) grade, PA CARGO supplies 1 part: grouped under the catalog's "Banner Kit (Overhaul Kit + Friction Clutch Plates)" designation — the notes column spells out what sets them apart. A representative part number is PA CARGO DK4400BS.

In the Deluxe Kit (Master Kit + Filter, Band & Common Bushings) grade, PA CARGO supplies 1 part: grouped under the catalog's "Deluxe Kit (Master Kit + Filter, Band & Common Bushings)" designation — the notes column spells out what sets them apart. A representative part number is PA CARGO MRK4400B.

The Master Kit (Overhaul Kit + Friction & Steel Clutch Plates) section lists 4 options from PIONEER, PA CARGO and ATP — grouped under the catalog's "Master Kit (Overhaul Kit + Friction & Steel Clutch Plates)" designation — the notes column spells out what sets them apart. PA CARGO DK4400B is listed in this group.

In the Overhaul Kit (Gaskets, Seals, O-Rings & Sealing Rings) grade, TRANSTEC, PIONEER and PA CARGO supply 6 parts: grouped under the catalog's "Overhaul Kit (Gaskets, Seals, O-Rings & Sealing Rings)" designation — the notes column spells out what sets them apart. A representative part number is PA CARGO K44900B.

This table covers the wear sleeves used to restore a grooved seal surface. Read more

2 Repair Sleeve parts are listed for the 2007 Jeep Commander, from SCHAEFFLER and SKF.