2011 Kia RIO5 Engine Parts

This table covers the camshafts that open the valves. Read more

One part is listed for the 2011 Kia RIO5 — HYUNDAI 2420026704.

This table covers the Camshaft plugs. Typical signs include a leak at the drain or glow-plug hole, or a plug that has rounded off. Replace the crush washer and torque to the spec in the notes. Read more

4 Camshaft Plug parts are listed for the 2011 Kia RIO5, from FEL-PRO, HYUNDAI, MAHLE / CLEVITE and 1 other brand.

This group includes FEL-PRO CP75023, HYUNDAI 2232735504 and MAHLE / CLEVITE 67728 and the remaining parts above.

This table covers the wear sleeves used to restore a Camshaft seal surface. Read more

6 Camshaft Repair Sleeve parts for the 2011 Kia RIO5 come from 6 brands — NATIONAL, SKF, BCA and 3 other brands. The "Popular" part is NATIONAL 99139.

This group includes NATIONAL 99139 and BCA NS99139 and the remaining parts above.

This table covers the seals at each camshaft end. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

11 Camshaft Seal parts for the 2011 Kia RIO5 come from 11 brands — NATIONAL, SKF, TIMKEN and 8 other brands. The "Popular" part is NATIONAL 3771.

This table covers the Circular / Semi-Circular plugs. Typical signs include a leak at the drain or glow-plug hole, or a plug that has rounded off. Replace the crush washer and torque to the spec in the notes. Read more

This group shows a single part: APEX ACP203.

This table covers the connecting rods between each piston and the crankshaft. Read more

One part is listed for the 2011 Kia RIO5 — TOPLINE CRHY2.

This table covers the bearings in the connecting-rod big ends. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

3 Connecting Rod Bearing parts are listed for the 2011 Kia RIO5, from KING ENGINE BEARINGS, MAHLE / CLEVITE and TOPLINE.

Listed part numbers: KING ENGINE BEARINGS CR4655AM, MAHLE / CLEVITE CB1979A4 and TOPLINE RBHY2.

This table covers lower / conversion gasket sets for oil-pan and related joints. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

6 Conversion / Lower Gasket Set parts are listed for the 2011 Kia RIO5, from FEL-PRO, ITM ENGINE COMPONENTS, AJUSA and 3 other brands. FEL-PRO CS262241 carries the "Popular" badge.

This group includes FEL-PRO CS262241, ITM ENGINE COMPONENTS 0921905 and AJUSA 54130100 and the remaining parts above.

This table covers the main bearings that support the crankshaft in the block. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

4 Crankshaft Main Bearing parts for the 2011 Kia RIO5 come from 3 brands — AUTO 7, KING ENGINE BEARINGS and TOPLINE.

This group includes AUTO 7 6000263, AUTO 7 6000266 and KING ENGINE BEARINGS MB5022AM and the remaining parts above.

This table covers the sleeves used to restore a grooved crankshaft seal surface. Read more

3 Crankshaft Repair Sleeve parts for the 2011 Kia RIO5 come from 3 brands — BCA, NATIONAL and WJB / INMOTION PARTS.

This group includes BCA NS99139, NATIONAL 99139 and WJB / INMOTION PARTS WS99139.

This table covers the front and rear seals that keep oil in at the crankshaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

13 Crankshaft Seal parts for the 2011 Kia RIO5 come from 9 brands — VICTOR REINZ, FEL-PRO, APEX and 6 other brands. The "Popular" part is FEL-PRO BS40672.

This table covers the bolts that clamp the cylinder head to the block. Read more

9 Cylinder Head Bolt parts are listed for the 2011 Kia RIO5, from AJUSA, ENGINETECH, APEX and 6 other brands. AJUSA 81029900 carries the "Popular" badge.

Listed part numbers: AJUSA 81029900, ENGINETECH HB251 and APEX AHB240, plus the other parts above.

This table covers the head gaskets that seal the block to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

7 Cylinder Head Gasket parts are listed for the 2011 Kia RIO5, from FEL-PRO, MAHLE / CLEVITE, AJUSA and 4 other brands. FEL-PRO 26224PT carries the "Popular" badge.

This group includes FEL-PRO 26224PT, MAHLE / CLEVITE 54484 and AJUSA 10183100 and the remaining parts above.

This table covers multi-piece gasket sets for a cylinder-head job. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

12 Cylinder Head Gasket Set parts are listed for the 2011 Kia RIO5, from ENGINETECH, FEL-PRO, AJUSA and 7 other brands. ENGINETECH HY16HSB carries the "Popular" badge.

This table covers the Cylinder Head Spacer shims. Read more

One part is listed for the 2011 Kia RIO5 — SBI 2302190.

This table covers the block heaters that warm the coolant or oil in cold weather. Read more

3 Engine Block Heater parts for the 2011 Kia RIO5 come from KAT'S HEATERS.

Part numbers include KAT'S HEATERS 11485, KAT'S HEATERS 11812 and KAT'S HEATERS 28812.

This table covers the Engine covers. Read more

TECHPRO supplies both parts for the 2011 Kia RIO5.

Part numbers include TECHPRO KI1228107 and TECHPRO KI1228108.

This table covers full gasket kits covering the joints opened in an engine rebuild. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

6 Engine Kit Gasket Set parts are listed for the 2011 Kia RIO5, from AJUSA, ENGINETECH, ITM ENGINE COMPONENTS and 2 other brands. ENGINETECH HY16K3 carries the "Popular" badge.

Part numbers include ENGINETECH HY16K3, ITM ENGINE COMPONENTS 0900880 and AJUSA 50287500, among others listed above.

This table covers the exhaust valves that let combustion gas out of the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

7 Exhaust Valve parts for the 2011 Kia RIO5 come from 6 brands — HYUNDAI, ENGINETECH, MELLING and 3 other brands. The "Popular" part is HYUNDAI 2221226050.

Part numbers include HYUNDAI 2221226050, HYUNDAI 2221226000 and ENGINETECH EM4421, among others listed above.

This table covers the Expansion plugs. Typical signs include a leak at the drain or glow-plug hole, or a plug that has rounded off. Replace the crush washer and torque to the spec in the notes. Read more

One part is listed for the 2011 Kia RIO5 — TOPLINE EPSC11.

This table covers the crankshaft pulleys / harmonic balancers at the front of the engine. Read more

6 Harmonic Balancer parts are listed for the 2011 Kia RIO5, from SKP, HL MANDO, ATP and 3 other brands. SKP SK594053 carries the "Popular" badge.

In the Economy grade, SKP supplies 1 part: the catalog's value-priced group. A representative part number is SKP SK594053.

The Standard Replacement section lists 5 options from HL MANDO, ATP, DAYCO and 2 other brands — built to original-equipment specification. HL MANDO 30A5012 is listed in this group.

Listed part numbers: SKP SK594053, HL MANDO 30A5012 and ATP 102152, plus the other parts above.

This table covers the gaskets between the intake manifold and the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

5 Intake Manifold Gasket parts are listed for the 2011 Kia RIO5, from FEL-PRO, AJUSA, APEX and 2 other brands. FEL-PRO MS96331 carries the "Popular" badge.

This group includes FEL-PRO MS96331, AJUSA 13224200 and APEX AMS2280 and the remaining parts above.

This table covers the intake valves that let air (and fuel, on port-injected engines) into the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

6 Intake Valve parts for the 2011 Kia RIO5 come from 6 brands — HYUNDAI, MELLING, ENGINETECH and 3 other brands. The "Popular" part is HYUNDAI 2221126600.

This group includes HYUNDAI 2221126600, MELLING V3047 and ENGINETECH IM4420 and the remaining parts above.

This table covers the mounts that hold the engine to the chassis. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes. Read more

16 Motor Mount parts for the 2011 Kia RIO5 come from 7 brands — WESTAR, ANCHOR, BECK/ARNLEY and 4 other brands. The "Popular" part is SKP SKM9324.

The Economy section: 1 option from SKP. SKP SKM9324 is listed in this group.

Standard Replacement: 15 parts, from WESTAR, ANCHOR, BECK/ARNLEY and 3 other brands. A representative part number is WESTAR EM9310.

This table covers the Motor Mount kits. Read more

2 Motor Mount Kit parts for the 2011 Kia RIO5 come from 2 brands — ANCHOR and WESTAR.

Listed part numbers: ANCHOR 300385 and WESTAR ETK071.

This table covers the engine oils listed by grade and specification for this engine. Typical signs include a low-oil lamp, knocking after a long interval, or oil that has gone thin and black well before the next service. Match the viscosity and spec in the notes (and on the filler cap). The tables group grades — they are not interchangeable. Read more

100 Oil parts for the 2011 Kia RIO5 come from 7 brands — VALVOLINE, LIQUI MOLY, MOBIL and 4 other brands. The "Popular" part is MOBIL 125195. Grades run from Conventional through Synthetic Blend; Full Synthetic is the most populated section, led by LIQUI MOLY, VALVOLINE, MOBIL and 3 other brands.

This table covers the Oil Cooler Mounting kits. Read more

HAYDEN supplies both parts for the 2011 Kia RIO5.

This group includes HAYDEN 238 and HAYDEN 153.

This table covers the drain plugs in the oil pan. Read more

5 Oil Drain Plug parts for the 2011 Kia RIO5 come from 3 brands — DORMAN, REIN and SKP. The "Popular" part is DORMAN 090053.

This group includes DORMAN 090053, DORMAN 090033 and DORMAN 092020 and the remaining parts above.

This table covers the crush washers and gaskets under the oil drain plug. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

4 Oil Drain Plug Gasket parts are listed for the 2011 Kia RIO5, from ACKOJA, DORMAN, FEL-PRO and 1 other brand.

Listed part numbers: ACKOJA A532804, DORMAN 095144 and FEL-PRO 73346, plus the other parts above.

This table covers the caps on the oil filler neck. Read more

4 Oil Filler Cap parts for the 2011 Kia RIO5 come from 4 brands — CALORSTAT, GATES, MOTORAD and 1 other brand.

Listed part numbers: CALORSTAT OC2331, GATES 31083 and MOTORAD MO151, plus the other parts above.

This table covers the oil filters that screw onto this engine's filter mount. Typical signs include low oil pressure after a service, or a filter that will not spin off because the old gasket stayed on the block. Lube the new gasket and tighten to the spec on the box; a double-gasket install dumps the sump on the first drive. Read more

22 Oil Filter parts for the 2011 Kia RIO5 come from 17 brands — BOSCH, VARIOUS MFR, WIX and 14 other brands. The "Popular" part is MOBIL M1104A.

The Economy section: 5 options from BOSCH, FRAM, FVP and 2 other brands. BOSCH 72228WS is listed in this group.

The High Performance / Heavy Duty section lists 2 options from MOBIL and WIX — grouped under the catalog's "High Performance / Heavy Duty" designation — the notes column spells out what sets them apart. MOBIL M1104A is listed in this group.

Standard Replacement: 15 parts, from HENGST, HYUNDAI, BOSCH and 10 other brands. A representative part number is BOSCH 3312.

This table covers the oil pans that hold the engine's oil sump. Read more

2 Oil Pan parts are listed for the 2011 Kia RIO5, from DORMAN and SPECTRA PREMIUM.

Part numbers include DORMAN 264043 and SPECTRA PREMIUM HYP17A.

This table covers the gaskets between the oil pan and the block. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

6 Oil Pan Gasket parts for the 2011 Kia RIO5 come from 5 brands — VICTOR REINZ, FEL-PRO, APEX and 2 other brands. The "Popular" part is FEL-PRO OS30780.

Part numbers include FEL-PRO OS30780, VICTOR REINZ 703141410 and APEX AOP290, among others listed above.

This table covers the Oil pumps. Typical signs include noise from the pump, no pressure, or fluid that never arrives at the outlet. Prime or fill the pump as the notes require. A dry start is a common way to kill a new unit. Read more

5 Oil Pump parts for the 2011 Kia RIO5 come from 5 brands — SKP, MELLING, ITM ENGINE COMPONENTS and 2 other brands. The "Popular" part is MELLING M270.

The Economy section: 1 option from SKP. SKP SKPM270 is listed in this group.

Standard Replacement: 4 parts, from MELLING, ITM ENGINE COMPONENTS, PIERBURG and 1 other brand. A representative part number is MELLING M270.

This group includes MELLING M270, SKP SKPM270 and ITM ENGINE COMPONENTS 0571528 and the remaining parts above.

This table covers the pickup tubes and screens that feed the oil pump. Read more

2 Oil Pump Pickup Tube / Screen parts are listed for the 2011 Kia RIO5, from MELLING and SEALED POWER.

Part numbers include MELLING 399S and SEALED POWER 22415093.

This table covers the Oil Temperature senders. Read more

One part is listed for the 2011 Kia RIO5 — VEMO V52721571.

This table covers the pistons that travel in each cylinder. Typical signs include knock, blow-by, or a cylinder that will not hold compression. Piston work is a short-block job. Match bore, pin and ring pack in the notes — not the photo. Read more

4 Piston parts are listed for the 2011 Kia RIO5, from ENGINETECH, MAHLE / CLEVITE and TOPLINE.

The Premium section lists 1 option from MAHLE / CLEVITE — a step above OE specification in materials, tolerances or warranty terms. MAHLE / CLEVITE 681090 is listed in this group.

The Standard Replacement section: 3 options from ENGINETECH and TOPLINE. ENGINETECH P4009 is listed in this group.

Part numbers include MAHLE / CLEVITE 681090, ENGINETECH P4009 and ENGINETECH K40094P, among others listed above.

This table covers the rings that seal each piston to the cylinder wall. Read more

4 Piston Ring parts are listed for the 2011 Kia RIO5, from HASTINGS MANUFACTURING, ENGINETECH and TOPLINE.

The Premium section: 1 option from ENGINETECH. ENGINETECH S76514 is listed in this group.

The Standard Replacement section: 3 options from HASTINGS MANUFACTURING and TOPLINE. HASTINGS MANUFACTURING 2C4526 is listed in this group.

Part numbers include ENGINETECH S76514, HASTINGS MANUFACTURING 2C4526 and HASTINGS MANUFACTURING 2C4526S, among others listed above.