2005 Toyota 4RUNNER Automatic Transmission Parts

This table covers the Boost valves. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

2 Boost Valve parts are listed for the 2005 Toyota 4RUNNER, from SONNAX and TRANSGO. All of them fit every engine offered in the 2005 4RUNNER.

Listed part numbers: SONNAX A750LB1 and TRANSGO A750BOOST.

This table covers the Bushing kits. Read more

2 Bushing Kit parts for the 2005 Toyota 4RUNNER come from 2 brands — DURA-BOND and PA CARGO. Every part fits both the 4.0L V6 and the 4.7L V8.

Listed part numbers: DURA-BOND TK22 and PA CARGO K127901.

This table covers the vents on a transmission or axle housing. Read more

One part is listed for the 2005 Toyota 4RUNNER — DORMAN 924284.

This table covers the clutch-plate packs inside the transmission or transfer case. Read more

3 Clutch Plate Pack parts for the 2005 Toyota 4RUNNER come from RAYBESTOS POWERTRAIN. Every part fits both the 4.0L V6 and the 4.7L V8.

In the Friction Plate Pack grade, RAYBESTOS POWERTRAIN supplies 2 parts: grouped under the catalog's "Friction Plate Pack" designation — the notes column spells out what sets them apart. A representative part number is RAYBESTOS POWERTRAIN FRMTOYTA49.

The Steel Plate Pack section lists 1 option from RAYBESTOS POWERTRAIN — grouped under the catalog's "Steel Plate Pack" designation — the notes column spells out what sets them apart. RAYBESTOS POWERTRAIN STMTOYTA49 is listed in this group.

Listed part numbers: RAYBESTOS POWERTRAIN FRMTOYTA49, RAYBESTOS POWERTRAIN RHT96204 and RAYBESTOS POWERTRAIN STMTOYTA49.

This table covers the seals at the Extension Housing. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

7 Extension Housing Seal parts are listed for the 2005 Toyota 4RUNNER, from NATIONAL, WJB / INMOTION PARTS, TIMKEN and 2 other brands. NATIONAL 710689 carries the "Popular" badge. All of them fit every engine offered in the 2005 4RUNNER.

This group includes NATIONAL 710689, TIMKEN 3459S and ATP RO77 and the remaining parts above.

This table covers the replacement filters for this application — the table heading and notes say which circuit. Typical signs include restricted flow — long cranking, weak airflow, or dirty fluid after a short interval. Seat the new filter so it cannot bypass, and use the grade the notes call for. Read more

11 Filter parts for the 2005 Toyota 4RUNNER come from 10 brands — VAICO, AUTOTECNICA, PA CARGO and 7 other brands. The "Popular" part is ATP B331. Every part fits both the 4.0L V6 and the 4.7L V8.

The Economy section lists 3 options from AUTOTECNICA, PA CARGO and VARIOUS MFR — the catalog's value-priced group. AUTOTECNICA TY1222957K is listed in this group.

In the Standard Replacement grade, VAICO, ATP, BECK/ARNLEY and 4 other brands supply 8 parts: built to original-equipment specification. A representative part number is ATP B331.

This table covers the heat exchangers that cool transmission fluid. Typical signs include fluid that overheats, a leak at the cooler fittings, or milky fluid that says coolant and ATF have mixed. Flush the lines when you replace a cooler. Cross-contamination is how a small leak becomes a transmission job. Read more

5 Fluid Cooler parts for the 2005 Toyota 4RUNNER come from 5 brands — SKP, CSF, DORMAN and 2 other brands. The "Popular" part is SKP SKTOC056. Every part fits both the 4.0L V6 and the 4.7L V8.

Listed part numbers: SKP SKTOC056, CSF 20016 and DORMAN 918238, plus the other parts above.

This table covers the Fluid Cooler Line hoses. Typical signs include swelling, cracks, a soft spot, or a leak at a clamp. Replace adjacent aged hoses while the system is drained — they share the same heat cycle. Read more

5 Fluid Cooler Line / Hose parts for the 2005 Toyota 4RUNNER come from 5 brands — REIN, DORMAN, SKP and 2 other brands. The "Popular" part is REIN TRC0520.

Part numbers include REIN TRC0520, DORMAN 624279 and SKP SK624279, among others listed above.

This table covers the Fluid Cooler O-rings. Typical signs include a seep at a fitting or a housing that weeps after a service. Lube the new O-ring with the fluid it will see, and do not roll it into the groove. Read more

This group shows a single part: AJUSA 13181750.

This table covers the pans that hold automatic-transmission fluid. Read more

3 Fluid Pan parts are listed for the 2005 Toyota 4RUNNER, from DORMAN, SKP and SPECTRA PREMIUM. All of them fit every engine offered in the 2005 4RUNNER.

Listed part numbers: DORMAN 265900, SKP SK265900 and SPECTRA PREMIUM TP0900.

This table covers the gaskets that seal the Fluid Pan. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

5 Fluid Pan Gasket parts for the 2005 Toyota 4RUNNER come from 4 brands — FEL-PRO, ATP, MAHLE / CLEVITE and 1 other brand. The "Popular" part is FEL-PRO TOS18736. Every part fits both the 4.0L V6 and the 4.7L V8.

Listed part numbers: FEL-PRO TOS18736, ATP RG85 and FEL-PRO TOS18740, plus the other parts above.

This table covers the Fluid Pump bushings. Typical signs include a clunk over bumps, or a torn or walked-out bushing you can see. Press the new bushing square. A cocked bushing will tear in a few thousand miles. Read more

This group shows a single part: DURA-BOND TOY4TG.

This table covers the precision wear sleeves used to restore a transmission pump seal surface. Read more

3 Fluid Pump Repair Sleeve parts are listed for the 2005 Toyota 4RUNNER, from BCA, NATIONAL and WJB / INMOTION PARTS. All of them fit every engine offered in the 2005 4RUNNER.

This group includes BCA NS99147, NATIONAL 99147 and WJB / INMOTION PARTS WS99147.

This table covers the seals at the Fluid Pump. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

5 Fluid Pump Seal parts are listed for the 2005 Toyota 4RUNNER, from NATIONAL, BCA, SCHAEFFLER and 2 other brands. NATIONAL 223830 carries the "Popular" badge. All of them fit every engine offered in the 2005 4RUNNER.

Listed part numbers: NATIONAL 223830, BCA NS223830 and SCHAEFFLER SS6193, plus the other parts above.

This table covers the Fluid temperature sensors. Typical signs include hard cold starts, a fan that never comes on, or a gauge that disagrees with the scan tool. A sensor that reads open or shorted is usually the part; an implausible-but-smooth reading can be wiring. Read more

2 Fluid Temperature Sensor parts for the 2005 Toyota 4RUNNER come from 2 brands — NTK and WELLS. Every part fits both the 4.0L V6 and the 4.7L V8.

This group includes NTK AT0024 and WELLS 5S5727.

This table covers the seals at the Manual Shaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

3 Manual Shaft Seal parts are listed for the 2005 Toyota 4RUNNER, from BCA, NATIONAL and WJB / INMOTION PARTS. All of them fit every engine offered in the 2005 4RUNNER.

Listed part numbers: BCA NS221207, NATIONAL 221207 and WJB / INMOTION PARTS WS221207.

This table covers the seals at the Output Shaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

2 Output Shaft Seal parts for the 2005 Toyota 4RUNNER come from SKF. Every part fits both the 4.0L V6 and the 4.7L V8.

This group includes SKF 15700 and SKF 17122.

This table covers the Pressure Control (EPC) solenoids. Typical signs include a harsh or missing shift, or a code for this solenoid circuit. Check resistance and the connector before dropping the pan for a solenoid. Read more

5 Pressure Control (EPC) Solenoid parts for the 2005 Toyota 4RUNNER come from 2 brands — ROSTRA and STANDARD MOTOR PRODUCTS. The "Popular" part is STANDARD MOTOR PRODUCTS TCS126. Every part fits both the 4.0L V6 and the 4.7L V8.

Listed part numbers: STANDARD MOTOR PRODUCTS TCS126, ROSTRA 520590 and ROSTRA 520610, plus the other parts above.

This table covers the rebuild kits for this assembly. Read more

4 Rebuild Kit parts are listed for the 2005 Toyota 4RUNNER, from PA CARGO and TRANSTEC. All of them fit every engine offered in the 2005 4RUNNER.

In the Banner Kit (Overhaul Kit + Friction Clutch Plates) grade, PA CARGO supplies 1 part: grouped under the catalog's "Banner Kit (Overhaul Kit + Friction Clutch Plates)" designation — the notes column spells out what sets them apart. A representative part number is PA CARGO DK12700S.

In the Deluxe Kit (Master Kit + Filter, Band & Common Bushings) grade, PA CARGO supplies 1 part: grouped under the catalog's "Deluxe Kit (Master Kit + Filter, Band & Common Bushings)" designation — the notes column spells out what sets them apart. A representative part number is PA CARGO MRK12700.

In the Overhaul Kit (Gaskets, Seals, O-Rings & Sealing Rings) grade, PA CARGO and TRANSTEC supply 2 parts: grouped under the catalog's "Overhaul Kit (Gaskets, Seals, O-Rings & Sealing Rings)" designation — the notes column spells out what sets them apart. A representative part number is PA CARGO K127900.

Part numbers include PA CARGO DK12700S, PA CARGO MRK12700 and PA CARGO K127900, among others listed above.

This table covers the Shift Improvement kits. Read more

2 Shift Improvement Kit parts for the 2005 Toyota 4RUNNER come from 2 brands — SONNAX and TRANSGO. Every part fits both the 4.0L V6 and the 4.7L V8.

This group includes SONNAX A750EA761EZIP and TRANSGO SKA750WTA.

This table covers the seals at the Shift Shaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

2 Shift Shaft Seal parts are listed for the 2005 Toyota 4RUNNER, from SCHAEFFLER and TIMKEN. All of them fit every engine offered in the 2005 4RUNNER.

This group includes SCHAEFFLER SS2111 and TIMKEN 221207.

This table covers the Shift solenoids. Typical signs include a harsh or missing shift, or a code for this solenoid circuit. Check resistance and the connector before dropping the pan for a solenoid. Read more

11 Shift Solenoid parts are listed for the 2005 Toyota 4RUNNER, from ROSTRA, STANDARD MOTOR PRODUCTS and BECK/ARNLEY. ROSTRA 520592 carries the "Popular" badge. 9 parts fit every engine; the other 2 are engine-specific.

This table covers the Torque converters. Typical signs include a sulfur smell, rattling substrate, or an efficiency code. Confirm CARB vs Federal certification in the notes before ordering. Read more

2 Torque Converter parts for the 2005 Toyota 4RUNNER come from TC REMANUFACTURING.

This group includes TC REMANUFACTURING TO90 and TC REMANUFACTURING TO83.

This table covers the Torque Converter Clutch solenoids. Typical signs include a harsh or missing shift, or a code for this solenoid circuit. Check resistance and the connector before dropping the pan for a solenoid. Read more

2 Torque Converter Clutch Solenoid parts for the 2005 Toyota 4RUNNER come from 2 brands — STANDARD MOTOR PRODUCTS and WELLS. 1 part fits every engine; the other 1 is engine-specific.

Part numbers include STANDARD MOTOR PRODUCTS TCS141 and WELLS 2N1425.

This table covers the wear sleeves used to restore a Torque Converter seal surface. Read more

One part is listed for the 2005 Toyota 4RUNNER — SCHAEFFLER SR3476.

This table covers the seals at the Torque Converter Shaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

2 Torque Converter Shaft Seal parts are listed for the 2005 Toyota 4RUNNER, from SCHAEFFLER and TIMKEN. All of them fit every engine offered in the 2005 4RUNNER.

Listed part numbers: SCHAEFFLER SS2518 and TIMKEN 223830.

This table covers the automatic-transmission fluids specified for this gearbox. Typical signs include harsh or delayed shifts, fluid that smells burnt, or a shudder at light throttle. Use exactly the specification in the notes. Automatic transmissions are unforgiving of the wrong fluid. Read more

21 Transmission Fluid parts for the 2005 Toyota 4RUNNER come from 10 brands — VALVOLINE, IDEMITSU, LIQUI MOLY and 7 other brands. The "Popular" part is ACDELCO 109243. 17 parts fit every engine; the other 4 are engine-specific.

In the ATF 64 grade, PENTOSIN supplies 2 parts: grouped under the catalog's "ATF 64" designation — the notes column spells out what sets them apart. A representative part number is PENTOSIN 1058113.

The Dexron section lists 1 option from ACDELCO — grouped under the catalog's "Dexron" designation — the notes column spells out what sets them apart. ACDELCO 109243 is listed in this group.

The Multi-Vehicle section lists 12 options from VALVOLINE, LIQUI MOLY, LUCAS OIL and 3 other brands — grouped under the catalog's "Multi-Vehicle" designation — the notes column spells out what sets them apart. MOBIL 126505 is listed in this group.

The Type T-4 (Type T-IV) section lists 2 options from IDEMITSU — grouped under the catalog's "Type T-4 (Type T-IV)" designation — the notes column spells out what sets them apart. IDEMITSU 30040093750 is listed in this group.

The World Standard (WS) section lists 3 options from IDEMITSU and AISIN — grouped under the catalog's "World Standard (WS)" designation — the notes column spells out what sets them apart. AISIN ATF0WS is listed in this group.

1 further part sits outside the graded sections, with the same engine-level match.

This table covers the conditioners and additives used with this transmission fluid. Read more

8 Transmission Fluid Additive parts for the 2005 Toyota 4RUNNER come from 2 brands — LUBEGARD and ATP. The "Popular" part is LUBEGARD 19610. Every part fits both the 4.0L V6 and the 4.7L V8.

This group includes LUBEGARD 19610, LUBEGARD 60902 and ATP AT203 and the remaining parts above.

This table covers the mounts that hold the transmission to the chassis. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes. Read more

14 Transmission Mount parts are listed for the 2005 Toyota 4RUNNER, from ANCHOR, DEA / MARMON RIDE CONTROL, WESTAR and 2 other brands. ANCHOR 9494 carries the "Popular" badge.