This page lists 32 engine parts for the 1992 Utilimaster Step Van, across 19 part types, covering both the 2.5L and the 3.3L. Every part shows its brand, manufacturer part number and fitment notes.
The engine on the 1992 Utilimaster Step Van covers the internals and hard parts that build compression and keep oil where it belongs — gaskets, bearings, camshafts, lifters, seals and timing components. The largest groups are Crankshaft Seal (4 parts), Cylinder Head Gasket (3 parts) and Cylinder Head Gasket Set (3 parts). The other 16 part types cover the remaining 22 parts.
The 1992 Utilimaster Step Van was sold with both the 2.5L and the 3.3L. 5 parts fit every engine; the other 27 are engine-specific. Each part shows which engine(s) it fits.
The most listed brands for 1992 Utilimaster Step Van engine parts are FEL-PRO (29 parts), VARIOUS MFR (2 parts) and ENGINE PRO (1 part). Quality grades include Economy and Standard Replacement.
Each part number listed for the 1992 Utilimaster Step Van opens a page with every vehicle that part fits.
Camshaft Plug
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| FEL-PRO Fits: 2.5L | TCS45833 | 🇺🇸 US | Rear | View on Amazon |
This table covers the Camshaft plugs. Typical signs include a leak at the drain or glow-plug hole, or a plug that has rounded off. Replace the crush washer and torque to the spec in the notes.
This group shows a single part: FEL-PRO TCS45833.
Camshaft Seal
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| FEL-PRO Fits: 2.5L | TCS45495 | 🇺🇸 US | Kit | View on Amazon |
This table covers the seals at each camshaft end. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again.
One part is listed for the 1992 Utilimaster Step Van — FEL-PRO TCS45495.
Conversion / Lower Gasket Set
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| ENGINE PRO Fits: 3.3L | 3796732 | 🇺🇸 US | View on Amazon | |
| FEL-PRO Fits: 3.3L | CS96732 | 🇺🇸 US | Permadry Rubber Oil Pan Gasket(s) Included | View on Amazon |
This table covers lower / conversion gasket sets for oil-pan and related joints. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration.
2 Conversion / Lower Gasket Set parts for the 1992 Utilimaster Step Van come from 2 brands — ENGINE PRO and FEL-PRO.
Part numbers include ENGINE PRO 3796732 and FEL-PRO CS96732.
Crankshaft Seal
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| FEL-PRO Fits: all 1992 Step Van engines | BS401681 | 🇺🇸 US | Rubber | View on Amazon |
| FEL-PRO Fits: 2.5L | TCS45131 | 🇺🇸 US | Front | View on Amazon |
| FEL-PRO Fits: all 1992 Step Van engines | BS40627 | 🇺🇸 US | PTFE RubberIncludes Sleeve | View on Amazon |
| FEL-PRO Fits: 3.3L | TCS46194 | 🇺🇸 US | Front | View on Amazon |
This table covers the front and rear seals that keep oil in at the crankshaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again.
FEL-PRO supplies the 4 Crankshaft Seal parts for the 1992 Utilimaster Step Van. 2 parts fit every engine; the other 2 are engine-specific.
This group includes FEL-PRO BS401681, FEL-PRO TCS45131 and FEL-PRO BS40627 and the remaining parts above.
Cylinder Head Bolt
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| FEL-PRO Fits: 3.3L | ES72849 | 🇺🇸 US | Set | View on Amazon |
This table covers the bolts that clamp the cylinder head to the block.
This group shows a single part: FEL-PRO ES72849.
Cylinder Head Bolt Washer
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| FEL-PRO Fits: 2.5L | ES72176 | 🇺🇸 US | View on Amazon | |
| FEL-PRO Fits: 3.3L | ES721761 | 🇺🇸 US | View on Amazon |
This table covers the Cylinder Head Bolt washers.
2 Cylinder Head Bolt Washer parts for the 1992 Utilimaster Step Van come from FEL-PRO.
This group includes FEL-PRO ES72176 and FEL-PRO ES721761.
Cylinder Head Gasket
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| FEL-PRO Fits: 2.5L | 9296PT | 🇺🇸 US | Permatorque | View on Amazon |
| FEL-PRO Fits: 3.3L | 9673PT1 | 🇺🇸 US | Right | View on Amazon |
| FEL-PRO Fits: 3.3L | 9676PT1 | 🇺🇸 US | Left | View on Amazon |
This table covers the head gaskets that seal the block to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for.
3 Cylinder Head Gasket parts for the 1992 Utilimaster Step Van come from FEL-PRO.
This group includes FEL-PRO 9296PT, FEL-PRO 9673PT1 and FEL-PRO 9676PT1.
Cylinder Head Gasket Set
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| FEL-PRO Fits: 2.5L | HS9296PT1 | 🇺🇸 US | Camshaft Rear Seal Not IncludedIncludes Permadry Molded Rubber Valve Cover Gasket(s), Valve Stem Seals | View on Amazon |
| FEL-PRO Fits: 3.3L | HIS9673PT | 🇺🇸 US | Installation Set For Fully Assembled HeadsIntake Manifold Gasket(s) Not Included | View on Amazon |
| FEL-PRO Fits: 3.3L | HS9673PT | 🇺🇸 US | Does Not Include Intake Manifold Gasket(S)Includes Permadry Molded Rubber Valve Cover Gasket(s), Valve Stem Seals | View on Amazon |
This table covers multi-piece gasket sets for a cylinder-head job. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration.
3 Cylinder Head Gasket Set parts for the 1992 Utilimaster Step Van come from FEL-PRO.
This group includes FEL-PRO HS9296PT1, FEL-PRO HIS9673PT and FEL-PRO HS9673PT.
Intake & Exhaust Manifold Gasket Set
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| FEL-PRO Fits: 2.5L | MS90947 | 🇺🇸 US | View on Amazon |
This table covers the Intake & Exhaust Manifold gasket sets. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration.
This group shows a single part: FEL-PRO MS90947.
Intake Manifold Gasket
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| FEL-PRO Fits: 3.3L | MS96042 | 🇺🇸 US | Includes Plenum GasketSet | View on Amazon |
This table covers the gaskets between the intake manifold and the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for.
This group shows a single part: FEL-PRO MS96042.
Intake Plenum Gasket
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| FEL-PRO Fits: 3.3L | MS94566 | 🇺🇸 US | Upper | View on Amazon |
This table covers the gaskets that seal the Intake Plenum. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for.
One part is listed for the 1992 Utilimaster Step Van — FEL-PRO MS94566.
Oil Drain Plug Gasket
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| FEL-PRO Fits: all 1992 Step Van engines | 70822 | 🇺🇸 US | 0.500 (in) Inside Diameter x 0.900 (in) Outside DiameterFlat Washer | View on Amazon |
This table covers the crush washers and gaskets under the oil drain plug. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for.
This group shows a single part: FEL-PRO 70822.
Oil Filter
Economy
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| VARIOUS MFR Fits: all 1992 Step Van engines | PG4670 | 🇺🇸 US | Spin-On | View on Amazon |
Standard Replacement
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| VARIOUS MFR Fits: all 1992 Step Van engines | PG4670EX | 🇺🇸 US | Extended LifeSpin-On | View on Amazon |
This table covers the oil filters that screw onto this engine's filter mount. Typical signs include low oil pressure after a service, or a filter that will not spin off because the old gasket stayed on the block. Lube the new gasket and tighten to the spec on the box; a double-gasket install dumps the sump on the first drive.
VARIOUS MFR supplies both parts for the 1992 Utilimaster Step Van. All of them fit every engine offered in the 1992 Step Van.
In the Economy grade, VARIOUS MFR supplies 1 part: the catalog's value-priced group. A representative part number is VARIOUS MFR PG4670.
The Standard Replacement section lists 1 option from VARIOUS MFR — built to original-equipment specification. VARIOUS MFR PG4670EX is listed in this group.
This group includes VARIOUS MFR PG4670 and VARIOUS MFR PG4670EX.
Oil Filter Adapter Gasket / O-Ring
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| FEL-PRO Fits: 3.3L | 73042 | 🇺🇸 US | View on Amazon | |
| FEL-PRO Fits: 3.3L | 71239 | 🇺🇸 US | Material: Composite | View on Amazon |
This table covers the Oil Filter Adapter Gasket O-rings. Typical signs include a seep at a fitting or a housing that weeps after a service. Lube the new O-ring with the fluid it will see, and do not roll it into the groove.
2 Oil Filter Adapter Gasket / O-Ring parts for the 1992 Utilimaster Step Van come from FEL-PRO.
Listed part numbers: FEL-PRO 73042 and FEL-PRO 71239.
Oil Pan Gasket
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| FEL-PRO Fits: 2.5L | OS30612R | 🇺🇸 US | Permadry | View on Amazon |
| FEL-PRO Fits: 3.3L | OS30622R | 🇺🇸 US | Permadry Molded Rubber | View on Amazon |
This table covers the gaskets between the oil pan and the block. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for.
FEL-PRO supplies both parts for the 1992 Utilimaster Step Van.
This group includes FEL-PRO OS30612R and FEL-PRO OS30622R.
Timing Cover Gasket
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| FEL-PRO Fits: 3.3L | TCS458931 | 🇺🇸 US | Must Use with Part Number(s) OS 30622 R | View on Amazon |
This table covers the gaskets that seal the Timing Cover. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for.
One part is listed for the 1992 Utilimaster Step Van — FEL-PRO TCS458931.
Timing Cover Repair Sleeve Tool
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| FEL-PRO Fits: 3.3L | 16326 | 🇺🇸 US | View on Amazon |
This table covers the Timing Cover Repair Sleeve tools. This is a service tool, not a wear part — match the application in the notes.
One part is listed for the 1992 Utilimaster Step Van — FEL-PRO 16326.
Valve Cover Gasket
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| FEL-PRO Fits: 2.5L | VS50334R | 🇺🇸 US | Permadry Molded Rubber | View on Amazon |
| FEL-PRO Fits: 3.3L | VS50339R | 🇺🇸 US | Permadry Molded Rubber | View on Amazon |
This table covers the gaskets that seal the valve cover to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for.
FEL-PRO supplies both parts for the 1992 Utilimaster Step Van.
Listed part numbers: FEL-PRO VS50334R and FEL-PRO VS50339R.
Valve Stem Seal
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| FEL-PRO Fits: 3.3L | SS72783 | 🇺🇸 US | Set | View on Amazon |
This table covers the seals on each valve stem that control oil into the guides. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again.
One part is listed for the 1992 Utilimaster Step Van — FEL-PRO SS72783.
Buying Engine Parts for a 1992 Utilimaster Step Van
On this vehicle, the engine covers the internals and hard parts that build compression and keep oil where it belongs — gaskets, bearings, camshafts, lifters, seals and timing components.
- Match the engine first. Some engine parts fit every engine; others are engine-specific. Each row shows which engine(s) it fits.
- Read the notes on each row for position, trim and spec qualifiers before you order.
- Where labor overlaps, replace the seals and gaskets for anything you open up; a timing job should always include the tensioner and guides, not just the belt or chain.
- Cross-reference the manufacturer part number against your old part or a service-manual listing.
Start with the largest groups on this page: Crankshaft Seal and Cylinder Head Gasket .
Frequently Asked Questions
How many engine parts fit the 1992 Utilimaster Step Van?
Our catalog currently lists 32 engine parts for the 1992 Utilimaster Step Van across 19 subcategories and 3 brands, covering both the 2.5L and the 3.3L. Each part is matched to the engine(s) it fits.
Do engine parts differ between 1992 Utilimaster Step Van engines?
Some do. 5 parts fit every engine; the other 27 are engine-specific. Each row (and the filter at the top) shows which. If you're unsure which engine you have, check the emissions label under the hood or the 8th character of your VIN.
What are the signs of engine problems on a 1992 Utilimaster Step Van?
Common symptoms include oil spots under the vehicle, blue or white exhaust smoke, ticking from the valvetrain, or coolant mysteriously disappearing. If you notice any of these, identify the affected subcategory above and cross-reference the part numbers listed.
What should I replace at the same time?
Where labor overlaps, replace the seals and gaskets for anything you open up; a timing job should always include the tensioner and guides, not just the belt or chain.
What do the market flags (US, CA, MX) on each part mean?
They show the market for which the manufacturer published application data for that part — where the vehicle was first sold, not where the part was made. If your 1992 Utilimaster Step Van was originally sold in the US, the safest choice is a part marked for the US market.
How do I make sure a part fits my 1992 Utilimaster Step Van?
First match the engine — each row shows which engine(s) the part fits. Then engine hard parts are unforgiving of guesswork — confirm the casting or engine code before ordering, because one model year can hide two different blocks. The notes column carries position and trim qualifiers where they apply.
Other Parts for the 1992 Utilimaster Step Van
Engine Parts for Other Utilimaster Step Van Years
Switch vehicle or jump to a subcategory
Manufacturer names, model designations and part numbers are used for identification and fitment reference only. AutoFactsDB is an independent catalog and is not affiliated with, endorsed by, or sponsored by any vehicle manufacturer displayed on this page.