2020 BMW 740I Engine Parts

This table covers lower / conversion gasket sets for oil-pan and related joints. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

One part is listed for the 2020 BMW 740I — AJUSA 54302500.

This table covers the main bearings that support the crankshaft in the block. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

2 Crankshaft Main Bearing parts for the 2020 BMW 740I come from KING ENGINE BEARINGS.

This group includes KING ENGINE BEARINGS MB7779SM and KING ENGINE BEARINGS MB7779MC.

This table covers the front and rear seals that keep oil in at the crankshaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

6 Crankshaft Seal parts for the 2020 BMW 740I come from 3 brands — MAHLE / CLEVITE, VICTOR REINZ and AJUSA. The "Popular" part is MAHLE / CLEVITE 68102.

This group includes MAHLE / CLEVITE 68102, VICTOR REINZ 813700200 and AJUSA 15075200 and the remaining parts above.

This table covers the bolts that clamp the cylinder head to the block. Read more

2 Cylinder Head Bolt parts are listed for the 2020 BMW 740I, from AJUSA and VICTOR REINZ.

This group includes AJUSA 81069200 and VICTOR REINZ 141226103.

This table covers the head gaskets that seal the block to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

6 Cylinder Head Gasket parts are listed for the 2020 BMW 740I, from ELRING, AJUSA and VICTOR REINZ. ELRING 793491 carries the "Popular" badge.

Listed part numbers: ELRING 793491, ELRING 739501 and AJUSA 10248900, plus the other parts above.

This table covers multi-piece gasket sets for a cylinder-head job. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

One part is listed for the 2020 BMW 740I — AJUSA 52561500.

This table covers the block heaters that warm the coolant or oil in cold weather. Read more

This group shows a single part: KAT'S HEATERS 28400.

This table covers the Engine covers. Read more

TECHPRO supplies the 3 Engine Cover parts for the 2020 BMW 740I.

This group includes TECHPRO BM1228189, TECHPRO BM1228184 and TECHPRO BM1228188.

This table covers full gasket kits covering the joints opened in an engine rebuild. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

One part is listed for the 2020 BMW 740I — AJUSA 50515000.

This table covers the followers that drive a mechanical fuel pump off the camshaft. Read more

One part is listed for the 2020 BMW 740I — WELLS 5T5004.

This table covers the Harmonic Balancer bolts. Read more

This group shows a single part: REIN HWB0074.

This table covers the gaskets between the intake manifold and the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

3 Intake Manifold Gasket parts are listed for the 2020 BMW 740I, from AJUSA, MAHLE / CLEVITE and VICTOR REINZ.

This group includes AJUSA 13313000, MAHLE / CLEVITE MS20642 and VICTOR REINZ 711737500.

This table covers the mounts that hold the engine to the chassis. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes. Read more

5 Motor Mount parts for the 2020 BMW 740I come from 2 brands — ANCHOR and WESTAR. The "Popular" part is ANCHOR 10258.

Part numbers include ANCHOR 10258, ANCHOR 10260 and ANCHOR 10259, among others listed above.

This table covers the Motor Mount kits. Read more

2 Motor Mount Kit parts for the 2020 BMW 740I come from ANCHOR.

This group includes ANCHOR 301068 and ANCHOR 300958.

This table covers the engine oils listed by grade and specification for this engine. Typical signs include a low-oil lamp, knocking after a long interval, or oil that has gone thin and black well before the next service. Match the viscosity and spec in the notes (and on the filler cap). The tables group grades — they are not interchangeable. Read more

7 Oil parts for the 2020 BMW 740I come from 4 brands — LIQUI MOLY, PENTOSIN, MOBIL and 1 other brand. The "Popular" part is LIQUI MOLY 22044.

Listed part numbers: LIQUI MOLY 22044, LIQUI MOLY 22046 and LIQUI MOLY 22048, plus the other parts above.

This table covers the heat exchangers that cool engine oil. Typical signs include oil at the cooler fittings, or coolant that looks like a milkshake. Pressure-test both circuits after a cooler swap — a leak here mixes oil and coolant. Read more

3 Oil Cooler parts for the 2020 BMW 740I come from 3 brands — NISSENS, REIN and VEMO.

Listed part numbers: NISSENS 91359, REIN ECK0273 and VEMO V20600077.

This table covers the gaskets that seal the Oil Cooler. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

3 Oil Cooler Gasket parts are listed for the 2020 BMW 740I, from AJUSA and MAHLE / CLEVITE.

Part numbers include AJUSA 77010300, AJUSA 77010400 and MAHLE / CLEVITE B33793.

This table covers the drain plugs in the oil pan. Read more

3 Oil Drain Plug parts for the 2020 BMW 740I come from 3 brands — AGS, DORMAN and REIN.

Part numbers include AGS ODP00010, DORMAN 090088 and REIN HWU1041.

This table covers the crush washers and gaskets under the oil drain plug. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

2 Oil Drain Plug Gasket parts are listed for the 2020 BMW 740I, from AJUSA and VICTOR REINZ.

Part numbers include AJUSA 21010400 and VICTOR REINZ 417005800.

This table covers the caps on the oil filler neck. Read more

2 Oil Filler Cap parts for the 2020 BMW 740I come from 2 brands — MOTORAD and VAICO.

This group includes MOTORAD MO214 and VAICO V204688.

This table covers the oil filters that screw onto this engine's filter mount. Typical signs include low oil pressure after a service, or a filter that will not spin off because the old gasket stayed on the block. Lube the new gasket and tighten to the spec on the box; a double-gasket install dumps the sump on the first drive. Read more

10 Oil Filter parts for the 2020 BMW 740I come from 10 brands — FVP, PRO-TEC, MOBIL and 7 other brands. The "Popular" part is HENGST E859HD352.

The Economy section lists 2 options from FVP and PRO-TEC — the catalog's value-priced group. FVP G0342 is listed in this group.

The High Performance / Heavy Duty section lists 1 option from MOBIL — grouped under the catalog's "High Performance / Heavy Duty" designation — the notes column spells out what sets them apart. MOBIL M1C457A is listed in this group.

In the Standard Replacement grade, HENGST, MANN, ACDELCO and 4 other brands supply 7 parts: built to original-equipment specification. A representative part number is HENGST E859HD352.

This table covers the Oil Filter Adapter Gasket O-rings. Typical signs include a seep at a fitting or a housing that weeps after a service. Lube the new O-ring with the fluid it will see, and do not roll it into the groove. Read more

One part is listed for the 2020 BMW 740I — MAHLE / CLEVITE B33794.

This table covers the Oil Filter covers. Read more

3 Oil Filter Cover parts are listed for the 2020 BMW 740I, from MOTORAD, REIN and VAICO.

Part numbers include MOTORAD MO388, REIN CPL0070 and VAICO V202772.

This table covers the Oil Filter housings. Read more

4 Oil Filter Housing parts are listed for the 2020 BMW 740I, from VEMO, DORMAN and HENGST.

Part numbers include DORMAN 926453, HENGST H811H and VEMO V20601662, among others listed above.

This table covers the Oil Level Sensor Gasket O-rings. Typical signs include a seep at a fitting or a housing that weeps after a service. Lube the new O-ring with the fluid it will see, and do not roll it into the groove. Read more

This group shows a single part: ELRING 078500.

This table covers the oil pans that hold the engine's oil sump. Read more

REIN supplies both parts for the 2020 BMW 740I.

Part numbers include REIN ESK0247 and REIN ESK0249.

This table covers the gaskets between the oil pan and the block. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

This group shows a single part: VICTOR REINZ 703141410.

This table covers the chains that drive the oil pump. Read more

5 Oil Pump Chain parts are listed for the 2020 BMW 740I, from S.A. GEAR, VAICO and CLOYES. VAICO V203921 carries the "Popular" badge.

In the Kit grade, VAICO supplies 1 part: grouped under the catalog's "Kit" designation — the notes column spells out what sets them apart. A representative part number is VAICO V203921.

The Standard Replacement section: 3 options from S.A. GEAR. S.A. GEAR C1213 is listed in this group.

1 ungrouped part is not assigned to a grade, with the same engine-level match.

This group includes VAICO V203921, S.A. GEAR C1213 and S.A. GEAR 76437P and the remaining parts above.

This table covers the Oil Pump sprockets. Read more

One part is listed for the 2020 BMW 740I — CLOYES S1172.

This table covers the rocker arms that transfer cam motion to the valves. Read more

This group shows a single part: INA VF0241.

This table covers the timing chains that keep the cams in time with the crank. Read more

2 Timing Chain parts are listed for the 2020 BMW 740I, from CLOYES and S.A. GEAR.

This group includes CLOYES C528 and S.A. GEAR C1162.

This table covers kits that group a timing chain with the related tensioners and guides. Read more

5 Timing Chain & Component Kit parts for the 2020 BMW 740I come from 3 brands — CLOYES, VAICO and S.A. GEAR. The "Popular" part is S.A. GEAR 76399.

The Economy section: 1 option from S.A. GEAR. S.A. GEAR 76399 is listed in this group.

Standard Replacement: 4 parts, from CLOYES and VAICO. A representative part number is CLOYES 90528SAX.

Listed part numbers: S.A. GEAR 76399, CLOYES 90528SAX and CLOYES 90528SA, plus the other parts above.

This table covers the guides and dampers that keep the timing chain on its path. Read more

5 Timing Chain Guide / Damper parts are listed for the 2020 BMW 740I, from CLOYES and S.A. GEAR. S.A. GEAR 71242 carries the "Popular" badge.

Listed part numbers: S.A. GEAR 71242, CLOYES 96180 and CLOYES 96181, plus the other parts above.

This table covers the tensioners that keep the timing chain taut. Typical signs include belt flutter, a chirp that returns after a new belt, or an arm that no longer damps. Replace the tensioner with the belt at higher mileage. Read more

2 Timing Chain Tensioner parts for the 2020 BMW 740I come from 2 brands — CLOYES and S.A. GEAR.

Listed part numbers: CLOYES 96179 and S.A. GEAR 91320.

This table covers the turbochargers that compress intake air. Read more

2 Turbocharger parts for the 2020 BMW 740I come from 2 brands — BORG-WARNER and GPD.

Part numbers include BORG-WARNER 18559880115 and GPD 2512001.

This table covers the Turbocharger Boost sensors. Typical signs include a warning lamp, a stored code, or a reading that drops out when the harness is wiggled. Inspect the connector and ground before replacing the sensor — wiring faults are often condemned as bad sensors. Read more

One part is listed for the 2020 BMW 740I — WELLS 5S14741.

This table covers the Turbocharger Coolant lines. Typical signs include a wet fitting, a rusted pipe, or a pressure loss in this circuit. Flare or thread the new line the way the notes specify; a kinked replacement will fail early. Read more

2 Turbocharger Coolant Line parts for the 2020 BMW 740I come from REIN.

Part numbers include REIN CHT0972 and REIN CHT0971.

This table covers the gaskets that seal the Turbocharger. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

2 Turbocharger Gasket parts are listed for the 2020 BMW 740I, from AJUSA and GPD.

Listed part numbers: AJUSA JTC12513 and GPD 2535112.

This table covers the fasteners that mount the turbocharger. Read more

One part is listed for the 2020 BMW 740I — REIN TRK0024.

This table covers the Turbocharger Oil lines. Typical signs include a wet fitting, a rusted pipe, or a pressure loss in this circuit. Flare or thread the new line the way the notes specify; a kinked replacement will fail early. Read more

3 Turbocharger Oil Line parts for the 2020 BMW 740I come from 2 brands — REIN and AJUSA.

Part numbers include AJUSA OP11237, REIN TFP0393 and REIN TRP0391.

This table covers the Turbocharger Oil Line Gasket O-rings. Typical signs include a seep at a fitting or a housing that weeps after a service. Lube the new O-ring with the fluid it will see, and do not roll it into the groove. Read more

This group shows a single part: AJUSA 16007800.

This table covers the Valve covers. Read more

2 Valve Cover parts are listed for the 2020 BMW 740I, from SKP and VAICO.

Listed part numbers: SKP SK743462 and VAICO V205366.

This table covers the gaskets that seal the valve cover to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

3 Valve Cover Gasket parts for the 2020 BMW 740I come from 3 brands — AJUSA, APEX and VICTOR REINZ.

This group includes AJUSA 56080600, APEX AVC983S and VICTOR REINZ 151120501.

This table covers the lifters / tappets that transfer cam motion to the valves. Read more

This group shows a single part: AJUSA 85022300.

This table covers the seals on each valve stem that control oil into the guides. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

5 Valve Stem Seal parts for the 2020 BMW 740I come from 3 brands — VICTOR REINZ, MAHLE / CLEVITE and AJUSA. The "Popular" part is VICTOR REINZ 123686601.

Listed part numbers: VICTOR REINZ 123686601, AJUSA 57051500 and MAHLE / CLEVITE SS46007, plus the other parts above.

This table covers the oil-control solenoids that command the cam phasers. Typical signs include a door or range that will not move, or a click with no motion. Confirm the command signal before replacing the actuator — a failed module looks the same. Read more

7 Variable Valve Timing (VVT) Solenoid / Actuator parts for the 2020 BMW 740I come from 6 brands — WELLS, GATES, WALKER PRODUCTS and 3 other brands. The "Popular" part is GATES VVS229.

The Economy section: 6 options from WELLS, GATES, WALKER PRODUCTS and 2 other brands. GATES VVS229 is listed in this group.

Standard Replacement: 1 part, from VAICO. A representative part number is VAICO V203797.

This group includes GATES VVS229, WALKER PRODUCTS 5901282 and HOLSTEIN 2VTS0370 and the remaining parts above.

This table covers the seals at the Variable Valve Timing (VVT) Solenoid Gasket. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

One part is listed for the 2020 BMW 740I — AJUSA 01907000.