2006 Chrysler 300 Automatic Transmission Parts

This table covers the pistons inside a transmission accumulator. Read more

MOPAR supplies both parts for the 2006 Chrysler 300.

Part numbers include MOPAR 4446544 and MOPAR 4446620AD.

This table covers the Accumulator springs. Typical signs include a sagging corner, a broken coil, or a clunk from the spring pocket. Replace springs in axle pairs and inspect the seats. Read more

MOPAR supplies both parts for the 2006 Chrysler 300.

This group includes MOPAR 4800310AA and MOPAR 4471880.

This table covers the control units that command automatic-transmission shifts. Read more

One part is listed for the 2006 Chrysler 300 — MOPAR 4692392AI.

This table covers the bushings in this assembly. Typical signs include a clunk over bumps, or a torn or walked-out bushing you can see. Press the new bushing square. A cocked bushing will tear in a few thousand miles. Read more

2 Bushing parts for the 2006 Chrysler 300 come from 2 brands — ATP and PIONEER.

Listed part numbers: ATP TB9 and PIONEER 755192.

This table covers the transmission or transfer-case housings. Read more

2 Case parts for the 2006 Chrysler 300 come from MOPAR.

This group includes MOPAR 52108099AB and MOPAR 52108484AB.

This table covers the Case covers. Read more

MOPAR supplies both parts for the 2006 Chrysler 300.

This group includes MOPAR 4591910AA and MOPAR 4591948AB.

This table covers the vents on a transmission or axle housing. Read more

MOPAR supplies both parts for the 2006 Chrysler 300.

Listed part numbers: MOPAR 5143951AA and MOPAR 5170944AC.

This table covers the pistons that apply a clutch pack. Read more

One part is listed for the 2006 Chrysler 300 — MOPAR 4431611.

This table covers the clutch-plate packs inside the transmission or transfer case. Read more

5 Clutch Plate Pack parts for the 2006 Chrysler 300 come from RAYBESTOS POWERTRAIN.

In the Friction Plate Pack grade, RAYBESTOS POWERTRAIN supplies 3 parts: grouped under the catalog's "Friction Plate Pack" designation — the notes column spells out what sets them apart. A representative part number is RAYBESTOS POWERTRAIN RCPS009.

The Steel Plate Pack section lists 1 option from RAYBESTOS POWERTRAIN — grouped under the catalog's "Steel Plate Pack" designation — the notes column spells out what sets them apart. RAYBESTOS POWERTRAIN 000408 is listed in this group.

1 further part sits outside the graded sections, with the same engine-level match.

Listed part numbers: RAYBESTOS POWERTRAIN RCPS009, RAYBESTOS POWERTRAIN RHT96009 and RAYBESTOS POWERTRAIN RHT96313, plus the other parts above.

This table covers the Conductor plates. Typical signs include warpage, cracks, or a plate that no longer locates the assembly. Confirm which plate the notes describe — backing plates, clutch plates and strike plates are different parts. Read more

6 Conductor Plate parts are listed for the 2006 Chrysler 300, from SKP, DORMAN, ULTRA-POWER and 2 other brands. SKP SK917678 carries the "Popular" badge.

In the Economy grade, SKP, DORMAN and ULTRA-POWER supply 4 parts: the catalog's value-priced group. A representative part number is SKP SK917678.

The Standard Replacement section lists 2 options from STANDARD MOTOR PRODUCTS and NTK — built to original-equipment specification. STANDARD MOTOR PRODUCTS TCP01 is listed in this group.

Part numbers include SKP SK917678, DORMAN 917678 and SKP SK917679, among others listed above.

This table covers the Dipstick / Fluid Filler tubes. Read more

2 Dipstick / Fluid Filler Tube parts for the 2006 Chrysler 300 come from 2 brands — DORMAN and MOPAR.

Listed part numbers: DORMAN 917327 and MOPAR 4591880AG.

This table covers the seals at the Dipstick / Fluid Filler Tube. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

One part is listed for the 2006 Chrysler 300 — ATP TO74.

This table covers the seals at the Extension Housing. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

20 Extension Housing Seal parts are listed for the 2006 Chrysler 300, from WJB / INMOTION PARTS, NATIONAL, BCA and 5 other brands. BCA NS224250 carries the "Popular" badge.

This table covers the replacement filters for this application — the table heading and notes say which circuit. Typical signs include restricted flow — long cranking, weak airflow, or dirty fluid after a short interval. Seat the new filter so it cannot bypass, and use the grade the notes call for. Read more

21 Filter parts for the 2006 Chrysler 300 come from 10 brands — ATP, VAICO, MOPAR and 7 other brands. The "Popular" part is ATP TF216.

In the Basic Kit (Without Transmission Fluid) grade, VAICO supplies 1 part: grouped under the catalog's "Basic Kit (Without Transmission Fluid)" designation — the notes column spells out what sets them apart. A representative part number is VAICO V302254BEK.

The Economy section: 7 options from ATP, ELRING, VARIOUS MFR and 1 other brand. ATP TF216 is listed in this group.

Standard Replacement: 13 parts, from MOPAR, ATP, HASTINGS / BALDWIN and 4 other brands. A representative part number is ACDELCO TF357.

This table covers the gaskets that seal the Filter. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

One part is listed for the 2006 Chrysler 300 — MOPAR 6032780.

This table covers the flexplates that connect the crankshaft to the torque converter. Read more

6 Flexplate parts are listed for the 2006 Chrysler 300, from ATP and PIONEER.

This group includes ATP Z494, ATP Z641 and ATP Z628 and the remaining parts above.

This table covers the Flexplate Mounting bolts. Read more

One part is listed for the 2006 Chrysler 300 — DORMAN 14131.

This table covers the Fluid Cooler Line hoses. Typical signs include swelling, cracks, a soft spot, or a leak at a clamp. Replace adjacent aged hoses while the system is drained — they share the same heat cycle. Read more

7 Fluid Cooler Line / Hose parts for the 2006 Chrysler 300 come from 3 brands — MOPAR, DORMAN and SUNSONG. The "Popular" part is DORMAN 624188.

This group includes DORMAN 624188, DORMAN 624186 and MOPAR 4598005AE and the remaining parts above.

This table covers the harness connectors at the Fluid Cooler Line / Hose. Typical signs include an intermittent fault that moves when you wiggle the plug, green corrosion, or a melted housing. Match terminal count and keyway, not just color. Many families look identical and will not lock. Read more

One part is listed for the 2006 Chrysler 300 — DORMAN 800723.

This table covers the pans that hold automatic-transmission fluid. Read more

10 Fluid Pan parts are listed for the 2006 Chrysler 300, from SKP, MOPAR, SPECTRA PREMIUM and 4 other brands. DORMAN 265818 carries the "Popular" badge.

This table covers the gaskets that seal the Fluid Pan. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

8 Fluid Pan Gasket parts for the 2006 Chrysler 300 come from 6 brands — FEL-PRO, MAHLE / CLEVITE, ÜRO PARTS and 3 other brands. The "Popular" part is FEL-PRO TOS18743.

Part numbers include FEL-PRO TOS18743, ÜRO PARTS 1402710080 and ATP MG4, among others listed above.

This table covers the Fluid Pan magnets. Read more

One part is listed for the 2006 Chrysler 300 — MOPAR 68207788AA.

This table covers the Fluid pressure sensors. Typical signs include a check-engine light for MAP or fuel-rail pressure, or a limp mode under load. A vacuum leak or a clogged reference line will fake a bad pressure sensor. Read more

5 Fluid Pressure Sensor parts are listed for the 2006 Chrysler 300, from WELLS, GPD, NTK and 2 other brands. WELLS 5S7002 carries the "Popular" badge.

This group includes WELLS 5S7002, GPD 1712661 and NTK AT0019 and the remaining parts above.

This table covers the Fluid pumps. Typical signs include noise from the pump, no pressure, or fluid that never arrives at the outlet. Prime or fill the pump as the notes require. A dry start is a common way to kill a new unit. Read more

3 Fluid Pump parts for the 2006 Chrysler 300 come from MOPAR.

This group includes MOPAR 5080070AB, MOPAR R8087860AA and MOPAR RL087860AA.

This table covers the Fluid Pump bushings. Typical signs include a clunk over bumps, or a torn or walked-out bushing you can see. Press the new bushing square. A cocked bushing will tear in a few thousand miles. Read more

This group shows a single part: DURA-BOND 01998TG.

This table covers the gaskets that seal the Fluid Pump. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

2 Fluid Pump Gasket parts are listed for the 2006 Chrysler 300, from MOPAR and PIONEER.

Part numbers include MOPAR 4412844 and PIONEER 749533.

This table covers the precision wear sleeves used to restore a transmission pump seal surface. Read more

One part is listed for the 2006 Chrysler 300 — WJB / INMOTION PARTS WS99149.

This table covers the seals at the Fluid Pump. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

10 Fluid Pump Seal parts are listed for the 2006 Chrysler 300, from NATIONAL, WJB / INMOTION PARTS, SKF and 4 other brands. NATIONAL 710608 carries the "Popular" badge.

This table covers the Fluid temperature sensors. Typical signs include hard cold starts, a fan that never comes on, or a gauge that disagrees with the scan tool. A sensor that reads open or shorted is usually the part; an implausible-but-smooth reading can be wiring. Read more

This group shows a single part: MOPAR 5149008AA.

This table covers the gasket kits for this job. Typical signs include the leaks that sent this assembly to the bench. Confirm the kit matches the opening you are sealing; unused leftover pieces often belong to another configuration. Read more

One part is listed for the 2006 Chrysler 300 — VICTOR REINZ 711917000.

This table covers the governors and modulators that control transmission shift pressure. Read more

This group shows a single part: DORMAN 601217.

This table covers the Input shafts. Read more

2 Input Shaft parts for the 2006 Chrysler 300 come from MOPAR.

Part numbers include MOPAR 5143679AB and MOPAR 52108044AA.

This table covers the Kickdown solenoids. Typical signs include a harsh or missing shift, or a code for this solenoid circuit. Check resistance and the connector before dropping the pan for a solenoid. Read more

2 Kickdown Solenoid parts are listed for the 2006 Chrysler 300, from DORMAN and MOPAR.

This group includes DORMAN 609041 and MOPAR 52108314AA.

This table covers the seals at the Manual Shaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

5 Manual Shaft Seal parts are listed for the 2006 Chrysler 300, from NATIONAL, WJB / INMOTION PARTS and BCA. NATIONAL 8609 carries the "Popular" badge.

This group includes NATIONAL 8609, BCA NS8609 and NATIONAL 711035 and the remaining parts above.

This table covers the O-rings and seals at this joint. Read more

One part is listed for the 2006 Chrysler 300 — ELRING 428390.

This table covers the Output Shaft bearings. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

9 Output Shaft Bearing parts are listed for the 2006 Chrysler 300, from NATIONAL, WJB / INMOTION PARTS, BCA and 2 other brands. WJB / INMOTION PARTS WTA18 carries the "Popular" badge.

Economy: 2 parts, from WJB / INMOTION PARTS. A representative part number is WJB / INMOTION PARTS WTA18.

The Standard Replacement section: 7 options from NATIONAL, BCA, SCHAEFFLER and 1 other brand. NATIONAL A18 is listed in this group.

Part numbers include WJB / INMOTION PARTS WTA18, WJB / INMOTION PARTS RB6206 and NATIONAL A18, among others listed above.

This table covers the seals at the Output Shaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

This group shows a single part: SKF 16521.

This table covers the parking pawls that lock the transmission in Park. Read more

This group shows a single part: MOPAR 52108154AA.

This table covers the Piston kits. Read more

One part is listed for the 2006 Chrysler 300 — PA CARGO 61837A.

This table covers the Plug adapters. Read more

2 Plug Adapter parts are listed for the 2006 Chrysler 300, from DORMAN and STANDARD MOTOR PRODUCTS.

Part numbers include DORMAN 917505 and STANDARD MOTOR PRODUCTS TCPA01.

This table covers the Pressure Control (EPC) solenoids. Typical signs include a harsh or missing shift, or a code for this solenoid circuit. Check resistance and the connector before dropping the pan for a solenoid. Read more

This group shows a single part: WELLS 2N1281.

This table covers the rebuild kits for this assembly. Read more

15 Rebuild Kit parts are listed for the 2006 Chrysler 300, from PA CARGO, PIONEER, TRANSTEC and 2 other brands. PA CARGO MRK6100A carries the "Popular" badge.

In the Banner Kit (Overhaul Kit + Friction Clutch Plates) grade, PA CARGO supplies 1 part: grouped under the catalog's "Banner Kit (Overhaul Kit + Friction Clutch Plates)" designation — the notes column spells out what sets them apart. A representative part number is PA CARGO DK6100AS.

In the Deluxe Kit (Master Kit + Filter, Band & Common Bushings) grade, PA CARGO supplies 1 part: grouped under the catalog's "Deluxe Kit (Master Kit + Filter, Band & Common Bushings)" designation — the notes column spells out what sets them apart. A representative part number is PA CARGO MRK6100A.

The Master Kit (Overhaul Kit + Friction & Steel Clutch Plates) section lists 6 options from PIONEER, ATP and PA CARGO — grouped under the catalog's "Master Kit (Overhaul Kit + Friction & Steel Clutch Plates)" designation — the notes column spells out what sets them apart. PA CARGO DK6100A is listed in this group.

In the Overhaul Kit (Gaskets, Seals, O-Rings & Sealing Rings) grade, TRANSTEC, PA CARGO and PIONEER supply 6 parts: grouped under the catalog's "Overhaul Kit (Gaskets, Seals, O-Rings & Sealing Rings)" designation — the notes column spells out what sets them apart. A representative part number is PA CARGO K61900A.

1 ungrouped part is not assigned to a grade, with the same engine-level match.

This table covers the wear sleeves used to restore a grooved seal surface. Read more

2 Repair Sleeve parts are listed for the 2006 Chrysler 300, from SCHAEFFLER and SKF.

This group includes SCHAEFFLER SR3502 and SKF 99182.

This table covers the Shift cables. Typical signs include a stretched or frayed cable, or a control that no longer reaches the end of its travel. Route the new cable through the same clips. A kinked cable binds and fails early. Read more

MOPAR supplies the 3 Shift Cable parts for the 2006 Chrysler 300.

This group includes MOPAR 4578072AD, MOPAR 4578073AD and MOPAR 4578074AA.

This table covers the Shift Improvement kits. Read more

2 Shift Improvement Kit parts for the 2006 Chrysler 300 come from 2 brands — SONNAX and TRANSGO.

Part numbers include SONNAX 22771TL12 and TRANSGO SK7226A.

This table covers the Shift Interlock control modules. Read more

2 Shift Interlock Control Module parts for the 2006 Chrysler 300 come from MOPAR.

Listed part numbers: MOPAR 68091341AA and MOPAR 68091343AA.

This table covers the Shift Interlock latches. Typical signs include a door that will not stay closed, or a latch that will not release. Lubricate and align the striker before replacing a latch that still clicks. Read more

2 Shift Interlock Latch parts are listed for the 2006 Chrysler 300, from DORMAN and SKP.

Listed part numbers: DORMAN 924706 and SKP SK924706.

This table covers the Shift Interlock solenoids. Typical signs include a harsh or missing shift, or a code for this solenoid circuit. Check resistance and the connector before dropping the pan for a solenoid. Read more

2 Shift Interlock Solenoid parts for the 2006 Chrysler 300 come from 2 brands — STANDARD MOTOR PRODUCTS and WELLS.

Listed part numbers: STANDARD MOTOR PRODUCTS SIA5 and WELLS 2N1318.

This table covers the Shift Linkage bushings. Typical signs include a clunk over bumps, or a torn or walked-out bushing you can see. Press the new bushing square. A cocked bushing will tear in a few thousand miles. Read more

One part is listed for the 2006 Chrysler 300 — DORMAN 14110.

This table covers the wear sleeves used to restore a Shift Shaft seal surface. Read more

One part is listed for the 2006 Chrysler 300 — SKF 99049.

This table covers the seals at the Shift Shaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

3 Shift Shaft Seal parts are listed for the 2006 Chrysler 300, from SCHAEFFLER and SKF.

This group includes SCHAEFFLER SS2178, SCHAEFFLER SS6528 and SKF 4692.