2007 Chrysler Cirrus Engine Parts

This table covers the seals at each camshaft end. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

3 Camshaft Seal parts are listed for the 2007 Chrysler Cirrus, from AJUSA, ELRING and SKF.

This group includes AJUSA 15058700, ELRING 127610 and SKF 14560.

This table covers the bearings in the connecting-rod big ends. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

This group shows a single part: KING ENGINE BEARINGS CR6810SI.

This table covers lower / conversion gasket sets for oil-pan and related joints. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

3 Conversion / Lower Gasket Set parts for the 2007 Chrysler Cirrus come from 2 brands — AJUSA and ELRING.

Listed part numbers: AJUSA 54153400, AJUSA 54165400 and ELRING 656420.

This table covers the main bearings that support the crankshaft in the block. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

2 Crankshaft Main Bearing parts are listed for the 2007 Chrysler Cirrus, from KING ENGINE BEARINGS and MAHLE / CLEVITE.

This group includes KING ENGINE BEARINGS MB4103SI and MAHLE / CLEVITE MS2299A.

This table covers the sleeves used to restore a grooved crankshaft seal surface. Read more

One part is listed for the 2007 Chrysler Cirrus — SCHAEFFLER SR4135.

This table covers the front and rear seals that keep oil in at the crankshaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

7 Crankshaft Seal parts are listed for the 2007 Chrysler Cirrus, from ELRING, AJUSA, SKF and 1 other brand.

This group includes AJUSA 15052700, AJUSA 15058600 and ELRING 034560 and the remaining parts above.

This table covers the bolts that clamp the cylinder head to the block. Read more

3 Cylinder Head Bolt parts for the 2007 Chrysler Cirrus come from 2 brands — AJUSA and ELRING.

Part numbers include AJUSA 81041900, AJUSA 81050400 and ELRING 657030.

This table covers the head gaskets that seal the block to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

8 Cylinder Head Gasket parts for the 2007 Chrysler Cirrus come from 2 brands — AJUSA and ELRING. The "Popular" part is ELRING 802960.

Listed part numbers: ELRING 802960, ELRING 797740 and AJUSA 10177100, plus the other parts above.

This table covers multi-piece gasket sets for a cylinder-head job. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

6 Cylinder Head Gasket Set parts for the 2007 Chrysler Cirrus come from 2 brands — ELRING and AJUSA.

This group includes AJUSA 52258800, AJUSA 52274000 and ELRING 448390 and the remaining parts above.

This table covers the wear sleeves used to restore a Cylinder seal surface. Read more

2 Cylinder Repair Sleeve parts for the 2007 Chrysler Cirrus come from MELLING.

Listed part numbers: MELLING CSL173 and MELLING CSL273.

This table covers full gasket kits covering the joints opened in an engine rebuild. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

2 Engine Kit Gasket Set parts for the 2007 Chrysler Cirrus come from AJUSA.

Listed part numbers: AJUSA 50276700 and AJUSA 50292800.

This table covers the crankshaft pulleys / harmonic balancers at the front of the engine. Read more

7 Harmonic Balancer parts for the 2007 Chrysler Cirrus come from 4 brands — ATP, DORMAN, SKP and 1 other brand. The "Popular" part is SKP SK594341.

The Economy section lists 1 option from SKP — the catalog's value-priced group. SKP SK594341 is listed in this group.

In the Standard Replacement grade, ATP, DORMAN and PIONEER supply 4 parts: built to original-equipment specification. A representative part number is ATP 102326.

2 further parts sit outside the graded sections, with the same engine-level match.

This group includes SKP SK594341, ATP 102326 and ATP 102326DA6024 and the remaining parts above.

This table covers the Intake manifolds. Typical signs include an exhaust tick, a vacuum leak, or a gasket that has burned through. Replace the gaskets and hardware; a warped flange will leak with a new gasket alone. Read more

2 Intake Manifold parts are listed for the 2007 Chrysler Cirrus, from DORMAN and LARES.

This group includes DORMAN 615801 and LARES 33850.

This table covers the Intake Manifold actuators. Typical signs include a door or range that will not move, or a click with no motion. Confirm the command signal before replacing the actuator — a failed module looks the same. Read more

This group shows a single part: DORMAN 911406.

This table covers the gaskets between the intake manifold and the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

3 Intake Manifold Gasket parts for the 2007 Chrysler Cirrus come from 2 brands — AJUSA and ELRING.

Listed part numbers: AJUSA 13216200, AJUSA 13171700 and ELRING 464050.

This table covers the gaskets that seal the Intake Plenum. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

AJUSA supplies both parts for the 2007 Chrysler Cirrus.

Part numbers include AJUSA 00986200 and AJUSA 01209900.

This table covers the engine oils listed by grade and specification for this engine. Typical signs include a low-oil lamp, knocking after a long interval, or oil that has gone thin and black well before the next service. Match the viscosity and spec in the notes (and on the filler cap). The tables group grades — they are not interchangeable. Read more

VALVOLINE supplies the 8 Oil parts for the 2007 Chrysler Cirrus. VALVOLINE 609506 carries the "Popular" badge.

The High Mileage (>75,000 Miles) section lists 4 options from VALVOLINE — oils grouped for high-mileage engines. VALVOLINE 609506 is listed in this group.

In the Synthetic Blend grade, VALVOLINE supplies 2 parts: synthetic-blend oils. A representative part number is VALVOLINE 797974.

2 ungrouped parts are not assigned to a grade, with the same engine-level match.

Part numbers include VALVOLINE 609506, VALVOLINE 849644 and VALVOLINE 881162, among others listed above.

This table covers the Oil Cooler Mounting kits. Read more

2 Oil Cooler Mounting Kit parts for the 2007 Chrysler Cirrus come from HAYDEN. Every part fits both the 2.4L L4 and the 3.5L V6.

Listed part numbers: HAYDEN 238 and HAYDEN 153.

This table covers the Oil Dipstick tubes. Read more

One part is listed for the 2007 Chrysler Cirrus — DORMAN 921126.

This table covers the drain plugs in the oil pan. Read more

7 Oil Drain Plug parts are listed for the 2007 Chrysler Cirrus, from DORMAN, ELRING, AGS and 1 other brand. AGS ODP00007 carries the "Popular" badge. 6 parts fit every engine; the other 1 is engine-specific.

This group includes AGS ODP00007, DORMAN 090053 and DORMAN 090115 and the remaining parts above.

This table covers the crush washers and gaskets under the oil drain plug. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

This group shows a single part: ELRING 176090.

This table covers the caps on the oil filler neck. Read more

3 Oil Filler Cap parts are listed for the 2007 Chrysler Cirrus, from MOTORAD and DORMAN.

Listed part numbers: DORMAN 80990, MOTORAD MO154 and MOTORAD MO158.

This table covers the oil filters that screw onto this engine's filter mount. Typical signs include low oil pressure after a service, or a filter that will not spin off because the old gasket stayed on the block. Lube the new gasket and tighten to the spec on the box; a double-gasket install dumps the sump on the first drive. Read more

24 Oil Filter parts are listed for the 2007 Chrysler Cirrus, from VARIOUS MFR, WIX, ACDELCO and 8 other brands. PRO-TEC PXL57060 carries the "Popular" badge. 1 part fits every engine; the other 23 are engine-specific.

Economy: 8 parts, from PRO-TEC, FVP, PUROLATOR and 1 other brand. A representative part number is PRO-TEC PXL57060.

In the High Performance / Heavy Duty grade, WIX and MOBIL supply 4 parts: grouped under the catalog's "High Performance / Heavy Duty" designation — the notes column spells out what sets them apart. A representative part number is WIX 57060XP.

The Standard Replacement section: 12 options from ACDELCO, WIX, HASTINGS / BALDWIN and 4 other brands. MOTORCRAFT FL300 is listed in this group.

This table covers the oil pans that hold the engine's oil sump. Read more

4 Oil Pan parts for the 2007 Chrysler Cirrus come from 3 brands — DORMAN, SKP and SPECTRA PREMIUM.

This group includes DORMAN 264361, DORMAN 264584 and SKP SK264361 and the remaining parts above.

This table covers the gaskets between the oil pan and the block. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

One part is listed for the 2007 Chrysler Cirrus — AJUSA 14095900.

This table covers the rings that seal each piston to the cylinder wall. Read more

3 Piston Ring parts for the 2007 Chrysler Cirrus come from MAHLE / CLEVITE.

Listed part numbers: MAHLE / CLEVITE 41676, MAHLE / CLEVITE 41857CP and MAHLE / CLEVITE 41856CP.

This table covers the Thrust washers. Read more

One part is listed for the 2007 Chrysler Cirrus — KING ENGINE BEARINGS TW170AM.

This table covers the Timing belts. Typical signs include squeal on cold start, cracked ribs, or glazing. Spin the tensioner and idlers by hand while the belt is off. Read more

This group shows a single part: BANDO TB295.

This table covers the Timing Belt & component kits. Read more

GMB supplies both parts for the 2007 Chrysler Cirrus.

Listed part numbers: GMB 34203295 and GMB 34202295.

This table covers the Timing Belt tensioners. Typical signs include belt flutter, a chirp that returns after a new belt, or an arm that no longer damps. Replace the tensioner with the belt at higher mileage. Read more

3 Timing Belt Tensioner parts are listed for the 2007 Chrysler Cirrus, from DORMAN and SKP.

Listed part numbers: DORMAN 420181, DORMAN 420154 and SKP SK85048.

This table covers the seals at the Timing Cover. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

3 Timing Cover Seal parts are listed for the 2007 Chrysler Cirrus, from SKF and SCHAEFFLER.

This group includes SCHAEFFLER SS4050, SKF 17122 and SKF 11417.

This table covers the Valve covers. Read more

This group shows a single part: DORMAN 264748.

This table covers the gaskets that seal the valve cover to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

4 Valve Cover Gasket parts are listed for the 2007 Chrysler Cirrus, from AJUSA, DORMAN and ELRING.

Part numbers include AJUSA 56040800, AJUSA 11117500 and DORMAN 263208, among others listed above.

This table covers the lifters / tappets that transfer cam motion to the valves. Read more

4 Valve Lifter parts are listed for the 2007 Chrysler Cirrus, from AJUSA and MELLING.

Part numbers include AJUSA 85011900, AJUSA 85011800 and AJUSA 85012200, among others listed above.

This table covers the seals on each valve stem that control oil into the guides. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

5 Valve Stem Seal parts are listed for the 2007 Chrysler Cirrus, from AJUSA and ELRING.

This group includes AJUSA 12025500, AJUSA 57047000 and AJUSA 57059400 and the remaining parts above.

This table covers the oil-control solenoids that command the cam phasers. Typical signs include a door or range that will not move, or a click with no motion. Confirm the command signal before replacing the actuator — a failed module looks the same. Read more

10 Variable Valve Timing (VVT) Solenoid / Actuator parts are listed for the 2007 Chrysler Cirrus, from SKP, DORMAN, ROSTRA and 2 other brands. SKP SK917291 carries the "Popular" badge.

Economy: 8 parts, from SKP, DORMAN, ROSTRA and 1 other brand. A representative part number is SKP SK917291.

The Standard Replacement section: 2 options from NTK. NTK VV0018 is listed in this group.