2008 Chrysler Cirrus Engine Parts

This table covers the Camshaft bearings. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

One part is listed for the 2008 Chrysler Cirrus — MAHLE / CLEVITE SH2163.

This table covers the seals at each camshaft end. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

3 Camshaft Seal parts for the 2008 Chrysler Cirrus come from 3 brands — AJUSA, ELRING and SKF.

Listed part numbers: AJUSA 15058700, ELRING 127610 and SKF 14560.

This table covers the bearings in the connecting-rod big ends. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

One part is listed for the 2008 Chrysler Cirrus — KING ENGINE BEARINGS CR6810SI.

This table covers lower / conversion gasket sets for oil-pan and related joints. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

3 Conversion / Lower Gasket Set parts are listed for the 2008 Chrysler Cirrus, from AJUSA and ELRING.

Listed part numbers: AJUSA 54153400, AJUSA 54165400 and ELRING 656420.

This table covers the main bearings that support the crankshaft in the block. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

2 Crankshaft Main Bearing parts for the 2008 Chrysler Cirrus come from 2 brands — KING ENGINE BEARINGS and MAHLE / CLEVITE.

This group includes KING ENGINE BEARINGS MB4103SI and MAHLE / CLEVITE MS2299A.

This table covers the sleeves used to restore a grooved crankshaft seal surface. Read more

This group shows a single part: SCHAEFFLER SR4135.

This table covers the front and rear seals that keep oil in at the crankshaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

6 Crankshaft Seal parts for the 2008 Chrysler Cirrus come from 5 brands — AJUSA, ELRING, SCHAEFFLER and 2 other brands. The "Popular" part is AJUSA 15052700.

This group includes AJUSA 15052700, AJUSA 15058600 and ELRING 034560 and the remaining parts above.

This table covers the bolts that clamp the cylinder head to the block. Read more

3 Cylinder Head Bolt parts are listed for the 2008 Chrysler Cirrus, from AJUSA and ELRING.

This group includes AJUSA 81041900, AJUSA 81050400 and ELRING 657030.

This table covers the head gaskets that seal the block to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

6 Cylinder Head Gasket parts are listed for the 2008 Chrysler Cirrus, from AJUSA and ELRING.

Listed part numbers: AJUSA 10177100, AJUSA 10139500 and AJUSA 10139600, plus the other parts above.

This table covers multi-piece gasket sets for a cylinder-head job. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

4 Cylinder Head Gasket Set parts are listed for the 2008 Chrysler Cirrus, from AJUSA and ELRING.

This group includes AJUSA 52258800, AJUSA 52274000 and ELRING 448390 and the remaining parts above.

This table covers the wear sleeves used to restore a Cylinder seal surface. Read more

MELLING supplies both parts for the 2008 Chrysler Cirrus.

This group includes MELLING CSL173 and MELLING CSL273.

This table covers full gasket kits covering the joints opened in an engine rebuild. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

AJUSA supplies both parts for the 2008 Chrysler Cirrus.

Listed part numbers: AJUSA 50276700 and AJUSA 50292800.

This table covers the crankshaft pulleys / harmonic balancers at the front of the engine. Read more

7 Harmonic Balancer parts are listed for the 2008 Chrysler Cirrus, from ATP, DORMAN, SKP and 1 other brand. SKP SK594341 carries the "Popular" badge.

In the Economy grade, SKP supplies 1 part: the catalog's value-priced group. A representative part number is SKP SK594341.

The Standard Replacement section lists 4 options from ATP, DORMAN and PIONEER — built to original-equipment specification. ATP 102326 is listed in this group.

2 ungrouped parts are not assigned to a grade, with the same engine-level match.

Part numbers include SKP SK594341, ATP 102326 and ATP 102326DA6024, among others listed above.

This table covers the Intake manifolds. Typical signs include an exhaust tick, a vacuum leak, or a gasket that has burned through. Replace the gaskets and hardware; a warped flange will leak with a new gasket alone. Read more

2 Intake Manifold parts for the 2008 Chrysler Cirrus come from 2 brands — DORMAN and LARES.

Part numbers include DORMAN 615801 and LARES 33850.

This table covers the Intake Manifold actuators. Typical signs include a door or range that will not move, or a click with no motion. Confirm the command signal before replacing the actuator — a failed module looks the same. Read more

One part is listed for the 2008 Chrysler Cirrus — DORMAN 911406.

This table covers the gaskets between the intake manifold and the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

3 Intake Manifold Gasket parts are listed for the 2008 Chrysler Cirrus, from AJUSA and ELRING.

This group includes AJUSA 13216200, AJUSA 13171700 and ELRING 464050.

This table covers the gaskets that seal the Intake Plenum. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

2 Intake Plenum Gasket parts for the 2008 Chrysler Cirrus come from AJUSA.

Part numbers include AJUSA 00986200 and AJUSA 01209900.

This table covers the engine oils listed by grade and specification for this engine. Typical signs include a low-oil lamp, knocking after a long interval, or oil that has gone thin and black well before the next service. Match the viscosity and spec in the notes (and on the filler cap). The tables group grades — they are not interchangeable. Read more

11 Oil parts for the 2008 Chrysler Cirrus come from VALVOLINE. The "Popular" part is VALVOLINE 797578.

The Conventional section lists 3 options from VALVOLINE — grouped under the catalog's "Conventional" designation — the notes column spells out what sets them apart. VALVOLINE 797578 is listed in this group.

In the High Mileage (>75,000 Miles) grade, VALVOLINE supplies 2 parts: oils grouped for high-mileage engines. A representative part number is VALVOLINE 797976.

6 further parts sit outside the graded sections, with the same engine-level match.

This table covers the Oil Cooler Mounting kits. Read more

HAYDEN supplies both parts for the 2008 Chrysler Cirrus. All of them fit every engine offered in the 2008 Cirrus.

Listed part numbers: HAYDEN 238 and HAYDEN 153.

This table covers the Oil Dipstick tubes. Read more

This group shows a single part: DORMAN 921126.

This table covers the drain plugs in the oil pan. Read more

6 Oil Drain Plug parts for the 2008 Chrysler Cirrus come from 4 brands — DORMAN, AGS, ELRING and 1 other brand. The "Popular" part is AGS ODP00007. 5 parts fit every engine; the other 1 is engine-specific.

This group includes AGS ODP00007, DORMAN 090053 and DORMAN 090115 and the remaining parts above.

This table covers the caps on the oil filler neck. Read more

3 Oil Filler Cap parts for the 2008 Chrysler Cirrus come from 2 brands — MOTORAD and DORMAN.

This group includes DORMAN 80990, MOTORAD MO154 and MOTORAD MO158.

This table covers the oil filters that screw onto this engine's filter mount. Typical signs include low oil pressure after a service, or a filter that will not spin off because the old gasket stayed on the block. Lube the new gasket and tighten to the spec on the box; a double-gasket install dumps the sump on the first drive. Read more

25 Oil Filter parts for the 2008 Chrysler Cirrus come from 11 brands — VARIOUS MFR, WIX, FVP and 8 other brands. The "Popular" part is WIX 57060XP. 1 part fits every engine; the other 24 are engine-specific.

The Economy section: 7 options from FVP, PRO-TEC, VARIOUS MFR and 1 other brand. FVP R7060 is listed in this group.

The High Performance / Heavy Duty section lists 4 options from WIX and MOBIL — grouped under the catalog's "High Performance / Heavy Duty" designation — the notes column spells out what sets them apart. WIX 57060XP is listed in this group.

Standard Replacement: 14 parts, from ACDELCO, MOTORCRAFT, WIX and 5 other brands. A representative part number is ACDELCO PF48.

This table covers the oil pans that hold the engine's oil sump. Read more

5 Oil Pan parts are listed for the 2008 Chrysler Cirrus, from DORMAN, SKP and SPECTRA PREMIUM.

Part numbers include DORMAN 264361, DORMAN 264855 and SKP SK264361, among others listed above.

This table covers the gaskets between the oil pan and the block. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

This group shows a single part: AJUSA 14095900.

This table covers the pistons that travel in each cylinder. Typical signs include knock, blow-by, or a cylinder that will not hold compression. Piston work is a short-block job. Match bore, pin and ring pack in the notes — not the photo. Read more

One part is listed for the 2008 Chrysler Cirrus — MAHLE / CLEVITE 2244006.

This table covers the rings that seal each piston to the cylinder wall. Read more

MAHLE / CLEVITE supplies both parts for the 2008 Chrysler Cirrus.

Listed part numbers: MAHLE / CLEVITE 42099CP and MAHLE / CLEVITE 41856CP.

This table covers the Thrust washers. Read more

This group shows a single part: KING ENGINE BEARINGS TW170AM.

This table covers the Timing belts. Typical signs include squeal on cold start, cracked ribs, or glazing. Spin the tensioner and idlers by hand while the belt is off. Read more

3 Timing Belt parts are listed for the 2008 Chrysler Cirrus, from BANDO, CLOYES and FVP.

Part numbers include BANDO TB295 and CLOYES B265, among others listed above.

This table covers the Timing Belt & component kits. Read more

4 Timing Belt & Component Kit parts for the 2008 Chrysler Cirrus come from 3 brands — GMB, CLOYES and FVP.

This group includes CLOYES BK265B and GMB 34203295 and the remaining parts above.

This table covers the Timing Belt tensioners. Typical signs include belt flutter, a chirp that returns after a new belt, or an arm that no longer damps. Replace the tensioner with the belt at higher mileage. Read more

5 Timing Belt Tensioner parts for the 2008 Chrysler Cirrus come from 4 brands — DORMAN, CLOYES, FVP and 1 other brand.

Part numbers include CLOYES 95543, DORMAN 420181 and DORMAN 420154, among others listed above.

This table covers the seals at the Timing Cover. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

3 Timing Cover Seal parts for the 2008 Chrysler Cirrus come from 2 brands — SKF and SCHAEFFLER.

Listed part numbers: SCHAEFFLER SS4050, SKF 17122 and SKF 11417.

This table covers the Timing idlers. Typical signs include a chirp that follows engine speed, or an idler that feels rough or has play. Replace a noisy idler with the belt — the labor is already paid for. Read more

2 Timing Idler parts for the 2008 Chrysler Cirrus come from 2 brands — CLOYES and FVP.

Part numbers include CLOYES 95542, among others listed above.

This table covers the Valve covers. Read more

One part is listed for the 2008 Chrysler Cirrus — DORMAN 264748.

This table covers the gaskets that seal the valve cover to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

4 Valve Cover Gasket parts for the 2008 Chrysler Cirrus come from 3 brands — AJUSA, DORMAN and ELRING.

Listed part numbers: AJUSA 56040800, AJUSA 11117500 and DORMAN 263208, plus the other parts above.

This table covers the lifters / tappets that transfer cam motion to the valves. Read more

4 Valve Lifter parts for the 2008 Chrysler Cirrus come from 2 brands — AJUSA and MELLING.

This group includes AJUSA 85011900, AJUSA 85011800 and AJUSA 85012200 and the remaining parts above.

This table covers the seals on each valve stem that control oil into the guides. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

5 Valve Stem Seal parts for the 2008 Chrysler Cirrus come from 2 brands — AJUSA and ELRING.

Listed part numbers: AJUSA 12025500, AJUSA 57047000 and AJUSA 57059400, plus the other parts above.

This table covers the oil-control solenoids that command the cam phasers. Typical signs include a door or range that will not move, or a click with no motion. Confirm the command signal before replacing the actuator — a failed module looks the same. Read more

10 Variable Valve Timing (VVT) Solenoid / Actuator parts for the 2008 Chrysler Cirrus come from 5 brands — SKP, DORMAN, ROSTRA and 2 other brands. The "Popular" part is SKP SK917291.

The Economy section: 8 options from SKP, DORMAN, ROSTRA and 1 other brand. SKP SK917291 is listed in this group.

Standard Replacement: 2 parts, from NTK. A representative part number is NTK VV0018.

This table covers the cam phaser sprockets used by the variable-valve-timing system. Read more

2 Variable Valve Timing (VVT) Sprocket parts for the 2008 Chrysler Cirrus come from DORMAN.

This group includes DORMAN 916539 and DORMAN 916538.