2006 Chrysler Cirrus Engine Parts

This table covers the chains that drive the balance shafts. Read more

One part is listed for the 2006 Chrysler Cirrus — MELLING 201.

This table covers the guides that keep the balance-shaft chain on its path. Read more

One part is listed for the 2006 Chrysler Cirrus — MELLING BG297.

This table covers the Balance Shaft Chain tensioners. Typical signs include belt flutter, a chirp that returns after a new belt, or an arm that no longer damps. Replace the tensioner with the belt at higher mileage. Read more

This group shows a single part: MELLING BT298.

This table covers the seals at each camshaft end. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

3 Camshaft Seal parts for the 2006 Chrysler Cirrus come from 2 brands — ELRING and AJUSA.

Listed part numbers: AJUSA 15012600, ELRING 353990 and ELRING 127610.

This table covers the bearings in the connecting-rod big ends. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

KING ENGINE BEARINGS supplies both parts for the 2006 Chrysler Cirrus.

This group includes KING ENGINE BEARINGS CR6780SI and KING ENGINE BEARINGS CR6781SI.

This table covers lower / conversion gasket sets for oil-pan and related joints. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

3 Conversion / Lower Gasket Set parts are listed for the 2006 Chrysler Cirrus, from AJUSA and ELRING.

This group includes AJUSA 54178200, AJUSA 54125000 and ELRING 656420.

This table covers the main bearings that support the crankshaft in the block. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

This group shows a single part: KING ENGINE BEARINGS MB4074SI.

This table covers the front and rear seals that keep oil in at the crankshaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

8 Crankshaft Seal parts for the 2006 Chrysler Cirrus come from 3 brands — VICTOR REINZ, ELRING and AJUSA. The "Popular" part is VICTOR REINZ 813479800. 1 part fits every engine; the other 7 are engine-specific.

Listed part numbers: VICTOR REINZ 813479800, AJUSA 15076500 and AJUSA 15081000, plus the other parts above.

This table covers the bolts that clamp the cylinder head to the block. Read more

3 Cylinder Head Bolt parts are listed for the 2006 Chrysler Cirrus, from AJUSA and ELRING.

Part numbers include AJUSA 81028400, AJUSA 81050600 and ELRING 657030.

This table covers the head gaskets that seal the block to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

9 Cylinder Head Gasket parts are listed for the 2006 Chrysler Cirrus, from AJUSA and ELRING. AJUSA 10157900 carries the "Popular" badge.

Part numbers include AJUSA 10157900, AJUSA 10150100 and AJUSA 10150200, among others listed above.

This table covers multi-piece gasket sets for a cylinder-head job. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

6 Cylinder Head Gasket Set parts are listed for the 2006 Chrysler Cirrus, from ELRING and AJUSA. ELRING 448390 carries the "Popular" badge.

This group includes ELRING 448390, AJUSA 52292000 and AJUSA 52208000 and the remaining parts above.

This table covers the wear sleeves used to restore a Cylinder seal surface. Read more

MELLING supplies both parts for the 2006 Chrysler Cirrus.

Listed part numbers: MELLING CSL1146 and MELLING CSL2246.

This table covers full gasket kits covering the joints opened in an engine rebuild. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

3 Engine Kit Gasket Set parts are listed for the 2006 Chrysler Cirrus, from AJUSA and ENGINE PRO.

Listed part numbers: AJUSA 50311700, AJUSA 50223200 and ENGINE PRO 305070.

This table covers the crankshaft pulleys / harmonic balancers at the front of the engine. Read more

8 Harmonic Balancer parts are listed for the 2006 Chrysler Cirrus, from ATP, DORMAN, PIONEER and 1 other brand. SKP SK594341 carries the "Popular" badge.

In the Economy grade, SKP supplies 1 part: the catalog's value-priced group. A representative part number is SKP SK594341.

The Standard Replacement section lists 4 options from ATP, DORMAN and PIONEER — built to original-equipment specification. ATP 102326 is listed in this group.

3 ungrouped parts are not assigned to a grade, with the same engine-level match.

This group includes SKP SK594341, ATP 102326 and ATP 102326DA6024 and the remaining parts above.

This table covers the gaskets between the intake manifold and the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

4 Intake Manifold Gasket parts are listed for the 2006 Chrysler Cirrus, from AJUSA and ELRING.

This group includes AJUSA 13183900, AJUSA 77022800 and AJUSA 13183700 and the remaining parts above.

This table covers the gaskets that seal the Intake Plenum. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

This group shows a single part: AJUSA 13183800.

This table covers the intake valves that let air (and fuel, on port-injected engines) into the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

This group shows a single part: MELLING V2008.

This table covers the mounts that hold the engine to the chassis. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes. Read more

2 Motor Mount parts for the 2006 Chrysler Cirrus come from 2 brands — ANCHOR and DEA / MARMON RIDE CONTROL.

This group includes ANCHOR 2841 and DEA / MARMON RIDE CONTROL A2841HY.

This table covers the engine oils listed by grade and specification for this engine. Typical signs include a low-oil lamp, knocking after a long interval, or oil that has gone thin and black well before the next service. Match the viscosity and spec in the notes (and on the filler cap). The tables group grades — they are not interchangeable. Read more

8 Oil parts for the 2006 Chrysler Cirrus come from VALVOLINE. The "Popular" part is VALVOLINE 609506.

In the High Mileage (>75,000 Miles) grade, VALVOLINE supplies 4 parts: oils grouped for high-mileage engines. A representative part number is VALVOLINE 609506.

The Synthetic Blend section lists 2 options from VALVOLINE — synthetic-blend oils. VALVOLINE 797974 is listed in this group.

2 further parts sit outside the graded sections, with the same engine-level match.

Part numbers include VALVOLINE 609506, VALVOLINE 849644 and VALVOLINE 881162, among others listed above.

This table covers the Oil Cooler Mounting kits. Read more

HAYDEN supplies both parts for the 2006 Chrysler Cirrus. All of them fit every engine offered in the 2006 Cirrus.

Part numbers include HAYDEN 238 and HAYDEN 153.

This table covers the Oil Dipstick tubes. Read more

This group shows a single part: DORMAN 917332.

This table covers the drain plugs in the oil pan. Read more

6 Oil Drain Plug parts for the 2006 Chrysler Cirrus come from 4 brands — DORMAN, AGS, ELRING and 1 other brand. The "Popular" part is AGS ODP00007. 5 parts fit every engine; the other 1 is engine-specific.

This group includes AGS ODP00007, DORMAN 090053 and DORMAN 090115 and the remaining parts above.

This table covers the caps on the oil filler neck. Read more

2 Oil Filler Cap parts for the 2006 Chrysler Cirrus come from MOTORAD.

This group includes MOTORAD MO111 and MOTORAD MO99.

This table covers the oil filters that screw onto this engine's filter mount. Typical signs include low oil pressure after a service, or a filter that will not spin off because the old gasket stayed on the block. Lube the new gasket and tighten to the spec on the box; a double-gasket install dumps the sump on the first drive. Read more

18 Oil Filter parts for the 2006 Chrysler Cirrus come from 10 brands — VARIOUS MFR, PUROLATOR, WIX and 7 other brands. The "Popular" part is WIX 51085XP. 4 parts fit every engine; the other 14 are engine-specific.

The Economy section: 7 options from PUROLATOR, VARIOUS MFR, CHAMP / LUBER-FINER and 2 other brands. CHAMP / LUBER-FINER PH400 is listed in this group.

The High Performance / Heavy Duty section lists 2 options from WIX and MOBIL — grouped under the catalog's "High Performance / Heavy Duty" designation — the notes column spells out what sets them apart. WIX 51085XP is listed in this group.

Standard Replacement: 9 parts, from MOTORCRAFT, ACDELCO, MANN and 2 other brands. A representative part number is MOTORCRAFT FL300.

This table covers the oil pans that hold the engine's oil sump. Read more

3 Oil Pan parts are listed for the 2006 Chrysler Cirrus, from DORMAN and SKP.

Listed part numbers: DORMAN 264242, DORMAN 264633 and SKP SK264242.

This table covers the gaskets between the oil pan and the block. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

4 Oil Pan Gasket parts for the 2006 Chrysler Cirrus come from 3 brands — AJUSA, MAHLE / CLEVITE and VICTOR REINZ.

Part numbers include AJUSA 14082500, AJUSA 14096600 and MAHLE / CLEVITE OS32156, among others listed above.

This table covers the pickup tubes and screens that feed the oil pump. Read more

One part is listed for the 2006 Chrysler Cirrus — MELLING 310S.

This table covers the rings that seal each piston to the cylinder wall. Read more

5 Piston Ring parts are listed for the 2006 Chrysler Cirrus, from MAHLE / CLEVITE and HASTINGS MANUFACTURING.

The Premium section lists 2 options from MAHLE / CLEVITE — a step above OE specification in materials, tolerances or warranty terms. MAHLE / CLEVITE 41676 is listed in this group.

The Standard Replacement section: 2 options from HASTINGS MANUFACTURING. HASTINGS MANUFACTURING 2C5125 is listed in this group.

1 ungrouped part is not assigned to a grade, with the same engine-level match.

Part numbers include MAHLE / CLEVITE 41676, MAHLE / CLEVITE 41857CP and HASTINGS MANUFACTURING 2C5125, among others listed above.

This table covers the rocker arms that transfer cam motion to the valves. Read more

This group shows a single part: MELLING MR1324.

This table covers the Timing belts. Typical signs include squeal on cold start, cracked ribs, or glazing. Spin the tensioner and idlers by hand while the belt is off. Read more

2 Timing Belt parts are listed for the 2006 Chrysler Cirrus, from BANDO and MELLING.

Part numbers include BANDO TB265 and MELLING B0265.

This table covers the Timing Belt tensioners. Typical signs include belt flutter, a chirp that returns after a new belt, or an arm that no longer damps. Replace the tensioner with the belt at higher mileage. Read more

3 Timing Belt Tensioner parts for the 2006 Chrysler Cirrus come from 3 brands — CLOYES, FVP and INA.

Part numbers include CLOYES 95544 and INA ZB0641, among others listed above.

This table covers the tensioners that keep the timing chain taut. Typical signs include belt flutter, a chirp that returns after a new belt, or an arm that no longer damps. Replace the tensioner with the belt at higher mileage. Read more

This group shows a single part: MELLING MSB02.

This table covers the wear sleeves used to restore a Timing Cover seal surface. Read more

This group shows a single part: SKF 99876.

This table covers the seals at the Timing Cover. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

This group shows a single part: SKF 12679.

This table covers the Timing idlers. Typical signs include a chirp that follows engine speed, or an idler that feels rough or has play. Replace a noisy idler with the belt — the labor is already paid for. Read more

5 Timing Idler parts for the 2006 Chrysler Cirrus come from 4 brands — INA, CLOYES, FVP and 1 other brand. The "Popular" part is CLOYES 95542.

This group includes CLOYES 95542 and INA ZP95542 and the remaining parts above.

This table covers the gaskets that seal the valve cover to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

6 Valve Cover Gasket parts for the 2006 Chrysler Cirrus come from 3 brands — AJUSA, ELRING and DORMAN.

Part numbers include AJUSA 56032700, AJUSA 56032500 and AJUSA 56032600, among others listed above.

This table covers the lifters / tappets that transfer cam motion to the valves. Read more

3 Valve Lifter parts for the 2006 Chrysler Cirrus come from 2 brands — AJUSA and MELLING.

Part numbers include AJUSA 85009700, AJUSA 85012800 and MELLING JB2240.

This table covers the seals on each valve stem that control oil into the guides. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

5 Valve Stem Seal parts for the 2006 Chrysler Cirrus come from 2 brands — AJUSA and ELRING. 1 part fits every engine; the other 4 are engine-specific.

Listed part numbers: AJUSA 12013600, AJUSA 57027400 and AJUSA 57055000, plus the other parts above.