2004 Chrysler Cirrus Engine Parts

This table covers the chains that drive the balance shafts. Read more

One part is listed for the 2004 Chrysler Cirrus — MELLING 201.

This table covers the guides that keep the balance-shaft chain on its path. Read more

One part is listed for the 2004 Chrysler Cirrus — MELLING BG297.

This table covers the Balance Shaft Chain tensioners. Typical signs include belt flutter, a chirp that returns after a new belt, or an arm that no longer damps. Replace the tensioner with the belt at higher mileage. Read more

3 Balance Shaft Chain Tensioner parts for the 2004 Chrysler Cirrus come from 3 brands — CLOYES, FVP and MELLING.

This group includes CLOYES 95298 and MELLING BT298 and the remaining parts above.

This table covers the seals at each camshaft end. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

2 Camshaft Seal parts for the 2004 Chrysler Cirrus come from 2 brands — AJUSA and ELRING.

Part numbers include AJUSA 15012600 and ELRING 353990.

This table covers the bearings in the connecting-rod big ends. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

KING ENGINE BEARINGS supplies both parts for the 2004 Chrysler Cirrus.

Part numbers include KING ENGINE BEARINGS CR6780SI and KING ENGINE BEARINGS CR6781SI.

This table covers lower / conversion gasket sets for oil-pan and related joints. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

AJUSA supplies both parts for the 2004 Chrysler Cirrus.

Part numbers include AJUSA 54178200 and AJUSA 54125000.

This table covers the main bearings that support the crankshaft in the block. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

This group shows a single part: KING ENGINE BEARINGS MB4074SI.

This table covers the front and rear seals that keep oil in at the crankshaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

10 Crankshaft Seal parts for the 2004 Chrysler Cirrus come from 4 brands — VICTOR REINZ, AJUSA, ELRING and 1 other brand. The "Popular" part is SKF 36204.

This table covers the bolts that clamp the cylinder head to the block. Read more

AJUSA supplies both parts for the 2004 Chrysler Cirrus.

Part numbers include AJUSA 81028400 and AJUSA 81050600.

This table covers the head gaskets that seal the block to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

10 Cylinder Head Gasket parts are listed for the 2004 Chrysler Cirrus, from AJUSA and ELRING. AJUSA 10150100 carries the "Popular" badge.

This table covers multi-piece gasket sets for a cylinder-head job. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

4 Cylinder Head Gasket Set parts are listed for the 2004 Chrysler Cirrus, from AJUSA and ELRING.

Listed part numbers: AJUSA 52292000, AJUSA 52208000 and ELRING 739880, plus the other parts above.

This table covers the wear sleeves used to restore a Cylinder seal surface. Read more

MELLING supplies both parts for the 2004 Chrysler Cirrus.

Part numbers include MELLING CSL1146 and MELLING CSL2246.

This table covers full gasket kits covering the joints opened in an engine rebuild. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

3 Engine Kit Gasket Set parts are listed for the 2004 Chrysler Cirrus, from AJUSA and ENGINE PRO.

Part numbers include AJUSA 50311700, AJUSA 50223200 and ENGINE PRO 305070.

This table covers the crankshaft pulleys / harmonic balancers at the front of the engine. Read more

3 Harmonic Balancer parts are listed for the 2004 Chrysler Cirrus, from ATP, DORMAN and PIONEER.

This group includes ATP 102336, DORMAN 594353 and PIONEER DA7027.

This table covers the gaskets between the intake manifold and the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

AJUSA supplies the 3 Intake Manifold Gasket parts for the 2004 Chrysler Cirrus.

This group includes AJUSA 13183900, AJUSA 77022800 and AJUSA 13183700.

This table covers the gaskets that seal the Intake Plenum. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

This group shows a single part: AJUSA 13183800.

This table covers the intake valves that let air (and fuel, on port-injected engines) into the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

This group shows a single part: MELLING V2008.

This table covers the mounts that hold the engine to the chassis. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes. Read more

2 Motor Mount parts for the 2004 Chrysler Cirrus come from 2 brands — ANCHOR and DEA / MARMON RIDE CONTROL.

Listed part numbers: ANCHOR 2841 and DEA / MARMON RIDE CONTROL A2841HY.

This table covers the engine oils listed by grade and specification for this engine. Typical signs include a low-oil lamp, knocking after a long interval, or oil that has gone thin and black well before the next service. Match the viscosity and spec in the notes (and on the filler cap). The tables group grades — they are not interchangeable. Read more

2 Oil parts for the 2004 Chrysler Cirrus come from VALVOLINE.

This group includes VALVOLINE VV180 and VALVOLINE 881170.

This table covers the Oil Cooler Mounting kits. Read more

HAYDEN supplies both parts for the 2004 Chrysler Cirrus. All of them fit every engine offered in the 2004 Cirrus.

Part numbers include HAYDEN 238 and HAYDEN 153.

This table covers the drain plugs in the oil pan. Read more

7 Oil Drain Plug parts for the 2004 Chrysler Cirrus come from 4 brands — DORMAN, ELRING, AGS and 1 other brand. The "Popular" part is AGS ODP00007. 6 parts fit every engine; the other 1 is engine-specific.

Listed part numbers: AGS ODP00007, DORMAN 090053 and DORMAN 090115, plus the other parts above.

This table covers the crush washers and gaskets under the oil drain plug. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

One part is listed for the 2004 Chrysler Cirrus — ELRING 176090.

This table covers the caps on the oil filler neck. Read more

This group shows a single part: MOTORAD MO111.

This table covers the oil filters that screw onto this engine's filter mount. Typical signs include low oil pressure after a service, or a filter that will not spin off because the old gasket stayed on the block. Lube the new gasket and tighten to the spec on the box; a double-gasket install dumps the sump on the first drive. Read more

17 Oil Filter parts for the 2004 Chrysler Cirrus come from 10 brands — PUROLATOR, VARIOUS MFR, MOBIL and 7 other brands. The "Popular" part is MOBIL M1102A. 6 parts fit every engine; the other 11 are engine-specific.

The Economy section lists 6 options from PUROLATOR, CHAMP / LUBER-FINER, FVP and 2 other brands — the catalog's value-priced group. CHAMP / LUBER-FINER PH400 is listed in this group.

The High Performance / Heavy Duty section lists 3 options from MOBIL and WIX — grouped under the catalog's "High Performance / Heavy Duty" designation — the notes column spells out what sets them apart. MOBIL M1102A is listed in this group.

In the Standard Replacement grade, MOTORCRAFT, ACDELCO, MANN and 2 other brands supply 8 parts: built to original-equipment specification. A representative part number is MOTORCRAFT FL300.

This table covers the oil pans that hold the engine's oil sump. Read more

One part is listed for the 2004 Chrysler Cirrus — DORMAN 264633.

This table covers the gaskets between the oil pan and the block. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

4 Oil Pan Gasket parts for the 2004 Chrysler Cirrus come from 3 brands — AJUSA, MAHLE / CLEVITE and VICTOR REINZ.

This group includes AJUSA 14082500, AJUSA 14096600 and MAHLE / CLEVITE OS32156 and the remaining parts above.

This table covers the pickup tubes and screens that feed the oil pump. Read more

One part is listed for the 2004 Chrysler Cirrus — MELLING 310S.

This table covers the pistons that travel in each cylinder. Typical signs include knock, blow-by, or a cylinder that will not hold compression. Piston work is a short-block job. Match bore, pin and ring pack in the notes — not the photo. Read more

SILV-O-LITE supplies both parts for the 2004 Chrysler Cirrus.

Listed part numbers: SILV-O-LITE 3235HC and SILV-O-LITE S3235HC.

This table covers the rings that seal each piston to the cylinder wall. Read more

5 Piston Ring parts are listed for the 2004 Chrysler Cirrus, from MAHLE / CLEVITE and HASTINGS MANUFACTURING.

The Premium section lists 2 options from MAHLE / CLEVITE — a step above OE specification in materials, tolerances or warranty terms. MAHLE / CLEVITE 41676 is listed in this group.

The Standard Replacement section: 2 options from HASTINGS MANUFACTURING. HASTINGS MANUFACTURING 2C5125 is listed in this group.

1 ungrouped part is not assigned to a grade, with the same engine-level match.

This group includes MAHLE / CLEVITE 41676, MAHLE / CLEVITE 41857CP and HASTINGS MANUFACTURING 2C5125 and the remaining parts above.

This table covers the rocker arms that transfer cam motion to the valves. Read more

This group shows a single part: MELLING MR1324.

This table covers the Timing belts. Typical signs include squeal on cold start, cracked ribs, or glazing. Spin the tensioner and idlers by hand while the belt is off. Read more

2 Timing Belt parts are listed for the 2004 Chrysler Cirrus, from BANDO and MELLING.

Part numbers include BANDO TB265 and MELLING B0265.

This table covers the Timing Belt tensioners. Typical signs include belt flutter, a chirp that returns after a new belt, or an arm that no longer damps. Replace the tensioner with the belt at higher mileage. Read more

3 Timing Belt Tensioner parts for the 2004 Chrysler Cirrus come from 3 brands — CLOYES, FVP and INA.

Listed part numbers: CLOYES 95544 and INA ZB0641, plus the other parts above.

This table covers the tensioners that keep the timing chain taut. Typical signs include belt flutter, a chirp that returns after a new belt, or an arm that no longer damps. Replace the tensioner with the belt at higher mileage. Read more

This group shows a single part: MELLING MSB02.

This table covers the wear sleeves used to restore a Timing Cover seal surface. Read more

This group shows a single part: SKF 99876.

This table covers the seals at the Timing Cover. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

This group shows a single part: SKF 12679.

This table covers the Timing idlers. Typical signs include a chirp that follows engine speed, or an idler that feels rough or has play. Replace a noisy idler with the belt — the labor is already paid for. Read more

5 Timing Idler parts for the 2004 Chrysler Cirrus come from 4 brands — INA, CLOYES, FVP and 1 other brand. The "Popular" part is CLOYES 95542.

This group includes CLOYES 95542 and INA ZP95542 and the remaining parts above.

This table covers the gaskets that seal the valve cover to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

5 Valve Cover Gasket parts for the 2004 Chrysler Cirrus come from 3 brands — AJUSA, DORMAN and ELRING.

This group includes AJUSA 56032700, AJUSA 56032500 and AJUSA 56032600 and the remaining parts above.

This table covers the lifters / tappets that transfer cam motion to the valves. Read more

3 Valve Lifter parts for the 2004 Chrysler Cirrus come from 2 brands — AJUSA and MELLING.

This group includes AJUSA 85009700, AJUSA 85012800 and MELLING JB2240.

This table covers the seals on each valve stem that control oil into the guides. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

4 Valve Stem Seal parts for the 2004 Chrysler Cirrus come from 2 brands — AJUSA and ELRING. 1 part fits every engine; the other 3 are engine-specific.

Part numbers include AJUSA 12013600, AJUSA 57027400 and AJUSA 57055000, among others listed above.