2008 Chrysler Voyager Engine Parts

This table covers the Camshaft bearings. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

This group shows a single part: MAHLE / CLEVITE SH1405S.

This table covers the Camshaft plugs. Typical signs include a leak at the drain or glow-plug hole, or a plug that has rounded off. Replace the crush washer and torque to the spec in the notes. Read more

This group shows a single part: DORMAN 555124.

This table covers the Camshaft Retainer / Thrust plates. Typical signs include warpage, cracks, or a plate that no longer locates the assembly. Confirm which plate the notes describe — backing plates, clutch plates and strike plates are different parts. Read more

One part is listed for the 2008 Chrysler Voyager — MELLING MD100.

This table covers the bearings in the connecting-rod big ends. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

6 Connecting Rod Bearing parts for the 2008 Chrysler Voyager come from 2 brands — MAHLE / CLEVITE and KING ENGINE BEARINGS. The "Popular" part is MAHLE / CLEVITE CB1410A.

Part numbers include MAHLE / CLEVITE CB1410A, MAHLE / CLEVITE CB1410A6 and KING ENGINE BEARINGS CR6675AM, among others listed above.

This table covers lower / conversion gasket sets for oil-pan and related joints. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

This group shows a single part: AJUSA 54165300.

This table covers the main bearings that support the crankshaft in the block. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

3 Crankshaft Main Bearing parts are listed for the 2008 Chrysler Voyager, from MAHLE / CLEVITE and KING ENGINE BEARINGS.

Listed part numbers: KING ENGINE BEARINGS MB4060SI, MAHLE / CLEVITE MS1946A and MAHLE / CLEVITE MS1946P.

This table covers the front and rear seals that keep oil in at the crankshaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

5 Crankshaft Seal parts are listed for the 2008 Chrysler Voyager, from ELRING and AJUSA. AJUSA 71005900 carries the "Popular" badge.

Listed part numbers: AJUSA 71005900, AJUSA 15058600 and ELRING 095390, plus the other parts above.

This table covers the bolts that clamp the cylinder head to the block. Read more

This group shows a single part: AJUSA 81049200.

This table covers the head gaskets that seal the block to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

6 Cylinder Head Gasket parts for the 2008 Chrysler Voyager come from 2 brands — AJUSA and ELRING. The "Popular" part is ELRING 590490.

This group includes ELRING 590490, ELRING 590480 and AJUSA 10187800 and the remaining parts above.

This table covers multi-piece gasket sets for a cylinder-head job. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

2 Cylinder Head Gasket Set parts for the 2008 Chrysler Voyager come from 2 brands — AJUSA and ELRING.

Listed part numbers: AJUSA 52273900 and ELRING 743980.

This table covers full gasket kits covering the joints opened in an engine rebuild. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

This group shows a single part: AJUSA 50292700.

This table covers the exhaust valves that let combustion gas out of the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

One part is listed for the 2008 Chrysler Voyager — MELLING V1994.

This table covers the crankshaft pulleys / harmonic balancers at the front of the engine. Read more

3 Harmonic Balancer parts for the 2008 Chrysler Voyager come from 3 brands — ATP, DORMAN and PIONEER.

This group includes ATP 102114, DORMAN 594103 and PIONEER DA203.

This table covers the gaskets between the intake manifold and the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

3 Intake Manifold Gasket parts for the 2008 Chrysler Voyager come from 2 brands — AJUSA and ELRING.

Part numbers include AJUSA 13216600, AJUSA 77046800 and ELRING B18990.

This table covers the gaskets that seal the Intake Plenum. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

One part is listed for the 2008 Chrysler Voyager — AJUSA 01163200.

This table covers the intake valves that let air (and fuel, on port-injected engines) into the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

One part is listed for the 2008 Chrysler Voyager — MELLING V1993.

This table covers the mounts that hold the engine to the chassis. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes. Read more

6 Motor Mount parts are listed for the 2008 Chrysler Voyager, from DEA / MARMON RIDE CONTROL, WESTAR, ANCHOR and 1 other brand. ANCHOR 2926 carries the "Popular" badge.

Part numbers include ANCHOR 2926, DEA / MARMON RIDE CONTROL A2928 and DEA / MARMON RIDE CONTROL A2926HY, among others listed above.

This table covers the Motor Mount bolts. Read more

This group shows a single part: DORMAN 926376.

This table covers the Motor Mount bushings. Typical signs include a clunk over bumps, or a torn or walked-out bushing you can see. Press the new bushing square. A cocked bushing will tear in a few thousand miles. Read more

One part is listed for the 2008 Chrysler Voyager — DEA / MARMON RIDE CONTROL AM012.

This table covers the Motor Mount kits. Read more

One part is listed for the 2008 Chrysler Voyager — ANCHOR 300247.

This table covers the engine oils listed by grade and specification for this engine. Typical signs include a low-oil lamp, knocking after a long interval, or oil that has gone thin and black well before the next service. Match the viscosity and spec in the notes (and on the filler cap). The tables group grades — they are not interchangeable. Read more

VALVOLINE supplies the 6 Oil parts for the 2008 Chrysler Voyager. VALVOLINE 797975 carries the "Popular" badge.

This group includes VALVOLINE 797975, VALVOLINE 881159 and VALVOLINE 797974 and the remaining parts above.

This table covers the Oil Cooler Mounting kits. Read more

2 Oil Cooler Mounting Kit parts for the 2008 Chrysler Voyager come from HAYDEN.

Listed part numbers: HAYDEN 238 and HAYDEN 153.

This table covers the Oil Dipstick tubes. Read more

2 Oil Dipstick / Tube parts are listed for the 2008 Chrysler Voyager, from DORMAN and SKP.

This group includes DORMAN 917320 and SKP SK917320.

This table covers the drain plugs in the oil pan. Read more

7 Oil Drain Plug parts are listed for the 2008 Chrysler Voyager, from DORMAN, ELRING, AGS and 1 other brand. AGS ODP00007 carries the "Popular" badge.

Part numbers include AGS ODP00007, DORMAN 090053 and DORMAN 090115, among others listed above.

This table covers the crush washers and gaskets under the oil drain plug. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

This group shows a single part: ELRING 176090.

This table covers the caps on the oil filler neck. Read more

2 Oil Filler Cap parts are listed for the 2008 Chrysler Voyager, from DORMAN and MOTORAD.

Listed part numbers: DORMAN 80990 and MOTORAD MO111.

This table covers the oil filters that screw onto this engine's filter mount. Typical signs include low oil pressure after a service, or a filter that will not spin off because the old gasket stayed on the block. Lube the new gasket and tighten to the spec on the box; a double-gasket install dumps the sump on the first drive. Read more

9 Oil Filter parts are listed for the 2008 Chrysler Voyager, from VARIOUS MFR, WIX, ACDELCO and 3 other brands. MOBIL M1102A carries the "Popular" badge.

In the Economy grade, FVP, PRO-TEC and VARIOUS MFR supply 3 parts: the catalog's value-priced group. A representative part number is FVP R1085.

In the High Performance / Heavy Duty grade, MOBIL and WIX supply 2 parts: grouped under the catalog's "High Performance / Heavy Duty" designation — the notes column spells out what sets them apart. A representative part number is MOBIL M1102A.

The Standard Replacement section lists 4 options from ACDELCO, WIX and VARIOUS MFR — built to original-equipment specification. WIX 51085 is listed in this group.

Listed part numbers: MOBIL M1102A, FVP R1085 and PRO-TEC PXL51085, plus the other parts above.

This table covers the seals at the Oil Filter Housing. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

One part is listed for the 2008 Chrysler Voyager — ELRING B19030.

This table covers the oil pans that hold the engine's oil sump. Read more

4 Oil Pan parts for the 2008 Chrysler Voyager come from 3 brands — SPECTRA PREMIUM, DORMAN and SKP.

Listed part numbers: DORMAN 264205, SKP SK264205 and SPECTRA PREMIUM CRP05A, plus the other parts above.

This table covers the gaskets between the oil pan and the block. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

2 Oil Pan Gasket parts are listed for the 2008 Chrysler Voyager, from AJUSA and ELRING.

Listed part numbers: AJUSA 14069500 and ELRING 590690.

This table covers the pickup tubes and screens that feed the oil pump. Read more

This group shows a single part: MELLING 263S.

This table covers the Oil Pump repair kits. Read more

2 Oil Pump Repair Kit parts for the 2008 Chrysler Voyager come from MELLING.

Listed part numbers: MELLING K391 and MELLING K391OS.

This table covers the rings that seal each piston to the cylinder wall. Read more

2 Piston Ring parts for the 2008 Chrysler Voyager come from 2 brands — HASTINGS MANUFACTURING and MAHLE / CLEVITE.

Listed part numbers: HASTINGS MANUFACTURING 2M5014 and MAHLE / CLEVITE 41860CP.

This table covers the pushrods that transfer lifter motion to the rocker arms. Read more

This group shows a single part: MELLING MPR663.

This table covers the Timing Cam sprockets. Read more

2 Timing Cam Sprocket parts are listed for the 2008 Chrysler Voyager, from CLOYES and FVP.

This group includes CLOYES S934T and the remaining parts above.

This table covers the timing chains that keep the cams in time with the crank. Read more

3 Timing Chain parts for the 2008 Chrysler Voyager come from 3 brands — CLOYES, FVP and MELLING.

Listed part numbers: CLOYES C300 and MELLING 300, plus the other parts above.

This table covers kits that group a timing chain with the related tensioners and guides. Read more

2 Timing Chain & Component Kit parts are listed for the 2008 Chrysler Voyager, from CLOYES and MELLING.

This group includes CLOYES C3235 and MELLING 33235S.

This table covers the gaskets that seal the Timing Cover. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

One part is listed for the 2008 Chrysler Voyager — ELRING 722550.

This table covers the wear sleeves used to restore a Timing Cover seal surface. Read more

One part is listed for the 2008 Chrysler Voyager — SKF 99112.

This table covers the seals at the Timing Cover. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

2 Timing Cover Seal parts are listed for the 2008 Chrysler Voyager, from SCHAEFFLER and SKF.

Part numbers include SCHAEFFLER SS2257 and SKF 11122.

This table covers the crankshaft sprockets that drive the timing chain or belt. Read more

2 Timing Crank Sprocket parts are listed for the 2008 Chrysler Voyager, from CLOYES and FVP.

This group includes CLOYES S927 and the remaining parts above.

This table covers the gaskets that seal the valve cover to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

3 Valve Cover Gasket parts are listed for the 2008 Chrysler Voyager, from ELRING and AJUSA.

This group includes AJUSA 11111800, ELRING 590500 and ELRING 095280.

This table covers the lifters / tappets that transfer cam motion to the valves. Read more

3 Valve Lifter parts are listed for the 2008 Chrysler Voyager, from MELLING and QUALCAST.

This group includes MELLING JB2225, MELLING JB2332 and QUALCAST 362332.

This table covers the springs that close each intake and exhaust valve. Typical signs include a sagging corner, a broken coil, or a clunk from the spring pocket. Replace springs in axle pairs and inspect the seats. Read more

This group shows a single part: MELLING VS1443.

This table covers the Valve Spring retainers. Read more

This group shows a single part: MELLING VSR705.

This table covers the keepers that lock each valve-spring retainer to the stem. Read more

This group shows a single part: MELLING VL1089.

This table covers the seals on each valve stem that control oil into the guides. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

AJUSA supplies both parts for the 2008 Chrysler Voyager.

Part numbers include AJUSA 12028100 and AJUSA 57054900.