1988 Detomaso Pantera Engine Parts

This table covers the Bolt kits. Read more

This group shows a single part: ARP 5549803.

This table covers the bearings in the connecting-rod big ends. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

3 Connecting Rod Bearing parts for the 1988 Detomaso Pantera come from KING ENGINE BEARINGS.

The High Performance section lists 2 options from KING ENGINE BEARINGS — engineered beyond original-equipment specification. KING ENGINE BEARINGS CR814XPN is listed in this group.

In the Standard Replacement grade, KING ENGINE BEARINGS supplies 1 part: built to original-equipment specification. A representative part number is KING ENGINE BEARINGS CR814SI.

This group includes KING ENGINE BEARINGS CR814XPN, KING ENGINE BEARINGS CR814XPNX and KING ENGINE BEARINGS CR814SI.

This table covers lower / conversion gasket sets for oil-pan and related joints. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

2 Conversion / Lower Gasket Set parts for the 1988 Detomaso Pantera come from 2 brands — FEL-PRO and VICTOR REINZ.

Listed part numbers: FEL-PRO CS85487 and VICTOR REINZ 081009501.

This table covers the main bearings that support the crankshaft in the block. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

KING ENGINE BEARINGS supplies the 3 Crankshaft Main Bearing parts for the 1988 Detomaso Pantera.

High Performance: 2 parts, from KING ENGINE BEARINGS. A representative part number is KING ENGINE BEARINGS MB5505XPX.

The Standard Replacement section: 1 option from KING ENGINE BEARINGS. KING ENGINE BEARINGS MB5505SI is listed in this group.

Listed part numbers: KING ENGINE BEARINGS MB5505XPX, KING ENGINE BEARINGS MB5505XP and KING ENGINE BEARINGS MB5505SI.

This table covers the Crankshaft Main Bearing Cap bolts. Read more

2 Crankshaft Main Bearing Cap Bolt parts for the 1988 Detomaso Pantera come from ARP.

Listed part numbers: ARP 1545001 and ARP 1545003.

This table covers the sleeves used to restore a grooved crankshaft seal surface. Read more

6 Crankshaft Repair Sleeve parts are listed for the 1988 Detomaso Pantera, from BCA, NATIONAL, FEL-PRO and 3 other brands. BCA NS88187 carries the "Popular" badge.

Part numbers include BCA NS88187, NATIONAL 99187 and FEL-PRO 16251, among others listed above.

This table covers the Crankshaft Repair Sleeve tools. This is a service tool, not a wear part — match the application in the notes. Read more

One part is listed for the 1988 Detomaso Pantera — VICTOR REINZ 711454000.

This table covers the front and rear seals that keep oil in at the crankshaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

16 Crankshaft Seal parts are listed for the 1988 Detomaso Pantera, from NATIONAL, WJB / INMOTION PARTS, FEL-PRO and 4 other brands. FEL-PRO BS40592 carries the "Popular" badge.

This table covers the bolts that clamp the cylinder head to the block. Read more

This group shows a single part: ARP 1543603.

This table covers the head gaskets that seal the block to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

5 Cylinder Head Gasket parts for the 1988 Detomaso Pantera come from 3 brands — FEL-PRO, MAHLE / CLEVITE and VICTOR REINZ. The "Popular" part is FEL-PRO 9333PT1.

This group includes FEL-PRO 9333PT1, FEL-PRO 8548PT2 and MAHLE / CLEVITE 3428 and the remaining parts above.

This table covers multi-piece gasket sets for a cylinder-head job. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

3 Cylinder Head Gasket Set parts for the 1988 Detomaso Pantera come from 3 brands — FEL-PRO, MAHLE / CLEVITE and VICTOR REINZ.

Listed part numbers: FEL-PRO HS8548PT9, MAHLE / CLEVITE HS3428R and VICTOR REINZ 021032001.

This table covers the Cylinder Head Spacer shims. Read more

2 Cylinder Head Spacer Shim parts for the 1988 Detomaso Pantera come from 2 brands — MAHLE / CLEVITE and VICTOR REINZ.

Listed part numbers: MAHLE / CLEVITE 3428SH and VICTOR REINZ 711638100.

This table covers the wear sleeves used to restore a Harmonic Balancer seal surface. Read more

4 Harmonic Balancer Repair Sleeve parts are listed for the 1988 Detomaso Pantera, from BCA, MAHLE / CLEVITE, NATIONAL and 1 other brand.

This group includes BCA NS88187, MAHLE / CLEVITE 66595RS and NATIONAL 88187 and the remaining parts above.

This table covers the Intake Manifold bolts. Read more

3 Intake Manifold Bolt parts for the 1988 Detomaso Pantera come from ARP.

Listed part numbers: ARP 1542001, ARP 4542001 and ARP 4542101.

This table covers the gaskets between the intake manifold and the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

4 Intake Manifold Gasket parts for the 1988 Detomaso Pantera come from 4 brands — FEL-PRO, MAHLE / CLEVITE, ULTRA-POWER and 1 other brand.

Part numbers include FEL-PRO MS90361 and MAHLE / CLEVITE MS15202, among others listed above.

This table covers the crush washers and gaskets under the oil drain plug. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

2 Oil Drain Plug Gasket parts for the 1988 Detomaso Pantera come from 2 brands — FEL-PRO and VICTOR REINZ.

Part numbers include FEL-PRO 70822 and VICTOR REINZ 711346200.

This table covers the oil filters that screw onto this engine's filter mount. Typical signs include low oil pressure after a service, or a filter that will not spin off because the old gasket stayed on the block. Lube the new gasket and tighten to the spec on the box; a double-gasket install dumps the sump on the first drive. Read more

FRAM supplies the 3 Oil Filter parts for the 1988 Detomaso Pantera.

In the Economy grade, FRAM supplies 1 part: the catalog's value-priced group. A representative part number is FRAM FE8A.

In the High Performance / Heavy Duty grade, FRAM supplies 1 part: grouped under the catalog's "High Performance / Heavy Duty" designation — the notes column spells out what sets them apart. A representative part number is FRAM TG8A.

The Standard Replacement section: 1 option from FRAM. FRAM PH8A is listed in this group.

Listed part numbers: FRAM FE8A, FRAM TG8A and FRAM PH8A.

This table covers the Oil Pan bolts. Read more

ARP supplies both parts for the 1988 Detomaso Pantera.

Listed part numbers: ARP 2541802 and ARP 2541901.

This table covers the gaskets between the oil pan and the block. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

5 Oil Pan Gasket parts are listed for the 1988 Detomaso Pantera, from FEL-PRO, VICTOR REINZ and MAHLE / CLEVITE. FEL-PRO OS30214C carries the "Popular" badge.

This group includes FEL-PRO OS30214C, FEL-PRO OS30616R and MAHLE / CLEVITE OS32492 and the remaining parts above.

This table covers the gaskets that seal the Oil Pump. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

3 Oil Pump Gasket parts for the 1988 Detomaso Pantera come from 3 brands — FEL-PRO, MAHLE / CLEVITE and VICTOR REINZ.

Part numbers include FEL-PRO 72607, MAHLE / CLEVITE B32041 and VICTOR REINZ 711407700.

This table covers the gaskets that seal the Oil Pump Pickup Tube. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

This group shows a single part: MAHLE / CLEVITE B26151.

This table covers the rings that seal each piston to the cylinder wall. Read more

5 Piston Ring parts for the 1988 Detomaso Pantera come from MAHLE / CLEVITE. The "Popular" part is MAHLE / CLEVITE 40564CP.

In the Premium grade, MAHLE / CLEVITE supplies 3 parts: a step above OE specification in materials, tolerances or warranty terms. A representative part number is MAHLE / CLEVITE 40564CP.

Standard Replacement: 2 parts, from MAHLE / CLEVITE. A representative part number is MAHLE / CLEVITE S50564CP.

Listed part numbers: MAHLE / CLEVITE 40564CP, MAHLE / CLEVITE S40564CP and MAHLE / CLEVITE 40451, plus the other parts above.

This table covers the gaskets that seal the Timing Cover. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

6 Timing Cover Gasket parts are listed for the 1988 Detomaso Pantera, from FEL-PRO, MAHLE / CLEVITE and VICTOR REINZ. FEL-PRO TCS45449 carries the "Popular" badge.

This group includes FEL-PRO TCS45449, FEL-PRO TCS45450 and MAHLE / CLEVITE T27802 and the remaining parts above.

This table covers the wear sleeves used to restore a Timing Cover seal surface. Read more

2 Timing Cover Repair Sleeve parts are listed for the 1988 Detomaso Pantera, from FEL-PRO and VICTOR REINZ.

This group includes FEL-PRO 16213 and VICTOR REINZ 711346500.

This table covers the Timing Cover Repair Sleeve tools. This is a service tool, not a wear part — match the application in the notes. Read more

One part is listed for the 1988 Detomaso Pantera — VICTOR REINZ 711541700.

This table covers the seals at the Timing Cover. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

One part is listed for the 1988 Detomaso Pantera — MAHLE / CLEVITE 46293.

This table covers the Timing Seal kits. Read more

This group shows a single part: MAGNUM BS23022.

This table covers the Valve covers. Read more

This group shows a single part: ENGINE PRO 311684.