1991 Eagle Summit Engine Parts

This table covers the Balance Shaft belts. Typical signs include squeal on cold start, cracked ribs, or glazing. Spin the tensioner and idlers by hand while the belt is off. Read more

This group shows a single part: BANDO TB168.

This table covers the Camshaft bearings. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

This group shows a single part: DURA-BOND MIA3.

This table covers the wear sleeves used to restore a Camshaft seal surface. Read more

5 Camshaft Repair Sleeve parts are listed for the 1991 Eagle Summit, from NATIONAL, BCA, SKF and 2 other brands. NATIONAL 99139 carries the "Popular" badge.

Listed part numbers: NATIONAL 99139, BCA NS99139 and SKF 99138, plus the other parts above.

This table covers the seals at each camshaft end. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

11 Camshaft Seal parts are listed for the 1991 Eagle Summit, from FEL-PRO, NATIONAL, TIMKEN and 8 other brands. FEL-PRO TCS45483 carries the "Popular" badge.

This table covers the connecting rods between each piston and the crankshaft. Read more

This group shows a single part: TOPLINE CRMI2.

This table covers the bearings in the connecting-rod big ends. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

3 Connecting Rod Bearing parts for the 1991 Eagle Summit come from 3 brands — KING ENGINE BEARINGS, MAHLE / CLEVITE and TOPLINE.

Listed part numbers: KING ENGINE BEARINGS CR4049AM, MAHLE / CLEVITE CB1588AL and TOPLINE RBMI2.

This table covers lower / conversion gasket sets for oil-pan and related joints. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

5 Conversion / Lower Gasket Set parts for the 1991 Eagle Summit come from 5 brands — APEX, AJUSA, FEL-PRO and 2 other brands. The "Popular" part is APEX ACS2000.

Part numbers include APEX ACS2000, AJUSA 54041100 and FEL-PRO CS87671, among others listed above.

This table covers the main bearings that support the crankshaft in the block. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

5 Crankshaft Main Bearing parts are listed for the 1991 Eagle Summit, from MAHLE / CLEVITE, BECK/ARNLEY, KING ENGINE BEARINGS and 2 other brands. MAHLE / CLEVITE MS1668P carries the "Popular" badge.

Listed part numbers: MAHLE / CLEVITE MS1668P, BECK/ARNLEY 0146510 and KING ENGINE BEARINGS MB5237AM, plus the other parts above.

This table covers the sleeves used to restore a grooved crankshaft seal surface. Read more

6 Crankshaft Repair Sleeve parts are listed for the 1991 Eagle Summit, from NATIONAL, WJB / INMOTION PARTS, FEL-PRO and 3 other brands. NATIONAL 99114 carries the "Popular" badge.

This group includes NATIONAL 99114, WJB / INMOTION PARTS WS99114 and FEL-PRO 16275 and the remaining parts above.

This table covers the front and rear seals that keep oil in at the crankshaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

17 Crankshaft Seal parts are listed for the 1991 Eagle Summit, from BECK/ARNLEY, FEL-PRO, MAHLE / CLEVITE and 9 other brands. BECK/ARNLEY 0523306 carries the "Popular" badge.

This table covers the bolts that clamp the cylinder head to the block. Read more

This group shows a single part: APEX AHB202.

This table covers the head gaskets that seal the block to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

6 Cylinder Head Gasket parts for the 1991 Eagle Summit come from 6 brands — BECK/ARNLEY, FEL-PRO, APEX and 3 other brands. The "Popular" part is BECK/ARNLEY 0351901.

This group includes BECK/ARNLEY 0351901, FEL-PRO 9758PT and APEX AHG202 and the remaining parts above.

This table covers multi-piece gasket sets for a cylinder-head job. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

6 Cylinder Head Gasket Set parts for the 1991 Eagle Summit come from 5 brands — FEL-PRO, BECK/ARNLEY, APEX and 2 other brands. The "Popular" part is BECK/ARNLEY 0322886.

This group includes BECK/ARNLEY 0322886, FEL-PRO HS9758PT and APEX AHS2002 and the remaining parts above.

This table covers the Cylinder Head plugs. Typical signs include a leak at the drain or glow-plug hole, or a plug that has rounded off. Replace the crush washer and torque to the spec in the notes. Read more

One part is listed for the 1991 Eagle Summit — DORMAN 565093.

This table covers the block heaters that warm the coolant or oil in cold weather. Read more

One part is listed for the 1991 Eagle Summit — KAT'S HEATERS 11411.

This table covers full gasket kits covering the joints opened in an engine rebuild. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

3 Engine Kit Gasket Set parts for the 1991 Eagle Summit come from 3 brands — AJUSA, APEX and TOPLINE.

Listed part numbers: AJUSA 50121000, APEX AFS2002 and TOPLINE CGSMI2.

This table covers the exhaust valves that let combustion gas out of the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

3 Exhaust Valve parts are listed for the 1991 Eagle Summit, from QUALCAST, SBI and TOPLINE.

Listed part numbers: QUALCAST 1010497, SBI 10497 and TOPLINE EVMI2L.

This table covers the Expansion plugs. Typical signs include a leak at the drain or glow-plug hole, or a plug that has rounded off. Replace the crush washer and torque to the spec in the notes. Read more

3 Expansion Plug parts for the 1991 Eagle Summit come from 2 brands — DORMAN and TOPLINE.

Part numbers include DORMAN 555093, DORMAN 565093 and TOPLINE EPSC11.

This table covers the crankshaft pulleys / harmonic balancers at the front of the engine. Read more

3 Harmonic Balancer parts for the 1991 Eagle Summit come from 3 brands — ATP, DORMAN and PIONEER.

This group includes ATP 102304, DORMAN 594876 and PIONEER DA152.

This table covers the gaskets between the intake manifold and the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

5 Intake Manifold Gasket parts for the 1991 Eagle Summit come from 5 brands — FEL-PRO, AJUSA, APEX and 2 other brands. The "Popular" part is FEL-PRO MS94789.

Part numbers include FEL-PRO MS94789, AJUSA 13088500 and APEX AMS2020, among others listed above.

This table covers the intake valves that let air (and fuel, on port-injected engines) into the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

5 Intake Valve parts are listed for the 1991 Eagle Summit, from SBI, TOPLINE and QUALCAST.

This group includes QUALCAST 1010495, SBI 10495 and SBI 10496 and the remaining parts above.

This table covers the mounts that hold the engine to the chassis. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes. Read more

13 Motor Mount parts are listed for the 1991 Eagle Summit, from DEA / MARMON RIDE CONTROL, WESTAR, PIONEER and 1 other brand. DEA / MARMON RIDE CONTROL A2673 carries the "Popular" badge.

This table covers the engine oils listed by grade and specification for this engine. Typical signs include a low-oil lamp, knocking after a long interval, or oil that has gone thin and black well before the next service. Match the viscosity and spec in the notes (and on the filler cap). The tables group grades — they are not interchangeable. Read more

26 Oil parts are listed for the 1991 Eagle Summit, from MOBIL and VALVOLINE. MOBIL 125195 carries the "Popular" badge. Grades run from Conventional through Synthetic Blend; High Mileage (>75,000 Miles) is the most populated section, led by MOBIL and VALVOLINE.

This table covers the Oil Cooler Mounting kits. Read more

2 Oil Cooler Mounting Kit parts for the 1991 Eagle Summit come from HAYDEN.

This group includes HAYDEN 238 and HAYDEN 153.

This table covers the drain plugs in the oil pan. Read more

6 Oil Drain Plug parts are listed for the 1991 Eagle Summit, from DORMAN, AGS, BECK/ARNLEY and 1 other brand. AGS ODP00007 carries the "Popular" badge.

This group includes AGS ODP00007, DORMAN 090053 and BECK/ARNLEY 0160088 and the remaining parts above.

This table covers the crush washers and gaskets under the oil drain plug. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

4 Oil Drain Plug Gasket parts for the 1991 Eagle Summit come from 4 brands — AJUSA, APEX, DORMAN and 1 other brand.

Part numbers include AJUSA 18001000, APEX ADP1906 and DORMAN 095141, among others listed above.

This table covers the caps on the oil filler neck. Read more

3 Oil Filler Cap parts are listed for the 1991 Eagle Summit, from ACDELCO, BECK/ARNLEY and MOTORAD.

Part numbers include ACDELCO 12C36, BECK/ARNLEY 0160050 and MOTORAD MO88.

This table covers the oil filters that screw onto this engine's filter mount. Typical signs include low oil pressure after a service, or a filter that will not spin off because the old gasket stayed on the block. Lube the new gasket and tighten to the spec on the box; a double-gasket install dumps the sump on the first drive. Read more

17 Oil Filter parts are listed for the 1991 Eagle Summit, from FAMOUS BRAND, FRAM, CHAMP / LUBER-FINER and 12 other brands. BOSCH 3421 carries the "Popular" badge.

In the Economy grade, FAMOUS BRAND, CHAMP / LUBER-FINER, FRAM and 5 other brands supply 9 parts: the catalog's value-priced group. A representative part number is CHAMP / LUBER-FINER PH2856A.

The Standard Replacement section lists 8 options from BOSCH, DENSO, HENGST and 5 other brands — built to original-equipment specification. BOSCH 3421 is listed in this group.

This table covers the Oil Level sensors. Typical signs include a warning lamp, a stored code, or a reading that drops out when the harness is wiggled. Inspect the connector and ground before replacing the sensor — wiring faults are often condemned as bad sensors. Read more

One part is listed for the 1991 Eagle Summit — WELLS 1S6556.

This table covers the oil pans that hold the engine's oil sump. Read more

6 Oil Pan parts for the 1991 Eagle Summit come from 6 brands — LILAND GLOBAL, ATP, DORMAN and 3 other brands. The "Popular" part is LILAND GLOBAL ICRP04B.

Part numbers include LILAND GLOBAL ICRP04B, ATP 103058 and DORMAN 264203, among others listed above.

This table covers the gaskets between the oil pan and the block. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

6 Oil Pan Gasket parts are listed for the 1991 Eagle Summit, from FEL-PRO, VICTOR REINZ, APEX and 3 other brands. FEL-PRO OS30414C carries the "Popular" badge.

Listed part numbers: FEL-PRO OS30414C, VICTOR REINZ 703141410 and APEX AOP200, plus the other parts above.

This table covers the Oil pumps. Typical signs include noise from the pump, no pressure, or fluid that never arrives at the outlet. Prime or fill the pump as the notes require. A dry start is a common way to kill a new unit. Read more

4 Oil Pump parts are listed for the 1991 Eagle Summit, from SKP, BECK/ARNLEY, MELLING and 1 other brand.

Economy: 1 part, from SKP. A representative part number is SKP SKPM170.

The Standard Replacement section: 3 options from BECK/ARNLEY, MELLING and TOPLINE. BECK/ARNLEY 0280279 is listed in this group.

Listed part numbers: SKP SKPM170, BECK/ARNLEY 0280279 and MELLING M170, plus the other parts above.

This table covers the pickup tubes and screens that feed the oil pump. Read more

This group shows a single part: MELLING 260S.

This table covers the pistons that travel in each cylinder. Typical signs include knock, blow-by, or a cylinder that will not hold compression. Piston work is a short-block job. Match bore, pin and ring pack in the notes — not the photo. Read more

3 Piston parts for the 1991 Eagle Summit come from 3 brands — BECK/ARNLEY, SILV-O-LITE and TOPLINE.

Part numbers include BECK/ARNLEY 0125200, SILV-O-LITE 3213H and TOPLINE PAMI2.

This table covers the rings that seal each piston to the cylinder wall. Read more

9 Piston Ring parts for the 1991 Eagle Summit come from 4 brands — HASTINGS MANUFACTURING, SEALED POWER, BECK/ARNLEY and 1 other brand. The "Popular" part is BECK/ARNLEY 0138168.

In the Premium grade, SEALED POWER and HASTINGS MANUFACTURING supply 3 parts: a step above OE specification in materials, tolerances or warranty terms. A representative part number is HASTINGS MANUFACTURING 2M5716.

Standard Replacement: 6 parts, from HASTINGS MANUFACTURING, BECK/ARNLEY, SEALED POWER and 1 other brand. A representative part number is BECK/ARNLEY 0138168.

This group includes BECK/ARNLEY 0138168, HASTINGS MANUFACTURING 2M5716 and SEALED POWER E516KC and the remaining parts above.

This table covers the rocker arms that transfer cam motion to the valves. Read more

TOPLINE supplies the 4 Rocker Arm parts for the 1991 Eagle Summit.

Listed part numbers: TOPLINE RAMI2RD, TOPLINE RAMI2RB and TOPLINE RAMI2RA, plus the other parts above.

This table covers the Rocker Arm shafts. Read more

TOPLINE supplies both parts for the 1991 Eagle Summit.

Part numbers include TOPLINE RASIMI2 and TOPLINE RASEMI2.

This table covers the Timing belts. Typical signs include squeal on cold start, cracked ribs, or glazing. Spin the tensioner and idlers by hand while the belt is off. Read more

7 Timing Belt parts for the 1991 Eagle Summit come from 5 brands — CONTINENTAL, DAYCO, GATES and 2 other brands. The "Popular" part is DAYCO 95191.

The Economy section: 2 options from CONTINENTAL. CONTINENTAL T128 is listed in this group.

Standard Replacement: 5 parts, from DAYCO, GATES, BANDO and 2 other brands. A representative part number is DAYCO 95191.

This group includes DAYCO 95191, CONTINENTAL T128 and CONTINENTAL T191 and the remaining parts above.

This table covers the Timing Belt & component kits. Read more

6 Timing Belt & Component Kit parts are listed for the 1991 Eagle Summit, from FVP, GATES, INA and 3 other brands. GATES TCK191 carries the "Popular" badge.

Economy: 1 part, from FVP. A representative part number is FVP BK191.

The Standard Replacement section: 5 options from GATES, INA, ACDELCO and 2 other brands. GATES TCK191 is listed in this group.

Listed part numbers: GATES TCK191, FVP BK191 and INA ZBBK191, plus the other parts above.

This table covers the Timing Belt tensioners. Typical signs include belt flutter, a chirp that returns after a new belt, or an arm that no longer damps. Replace the tensioner with the belt at higher mileage. Read more

5 Timing Belt Tensioner parts are listed for the 1991 Eagle Summit, from CLOYES, DAYCO, GMB and 2 other brands. CLOYES 95224 carries the "Popular" badge.

Listed part numbers: CLOYES 95224, DAYCO 84072 and GMB 4488090, plus the other parts above.

This table covers the wear sleeves used to restore a Timing Cover seal surface. Read more

One part is listed for the 1991 Eagle Summit — SKF 99114.

This table covers the seals at the Timing Cover. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

2 Timing Cover Seal parts are listed for the 1991 Eagle Summit, from SCHAEFFLER and SKF.

Listed part numbers: SCHAEFFLER SS2289 and SKF 11671.

This table covers the Timing idlers. Typical signs include a chirp that follows engine speed, or an idler that feels rough or has play. Replace a noisy idler with the belt — the labor is already paid for. Read more

2 Timing Idler parts are listed for the 1991 Eagle Summit, from INA and S.A. GEAR.

Part numbers include INA ZT95224 and S.A. GEAR 9224.

This table covers the gaskets that seal the valve cover to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

7 Valve Cover Gasket parts are listed for the 1991 Eagle Summit, from FEL-PRO, MAHLE / CLEVITE, APEX and 4 other brands. FEL-PRO VS50382R carries the "Popular" badge.

Listed part numbers: FEL-PRO VS50382R, MAHLE / CLEVITE VS50151 and APEX AVC202, plus the other parts above.

This table covers the pressed-in bronze and cast-iron guides that align valve stems. Typical signs include oil smoke on startup, a guide that has gone oval, or a valve that no longer seats quietly. Guides are a machine-shop fit. Confirm stem diameter in the notes before ordering. Read more

6 Valve Guide parts are listed for the 1991 Eagle Summit, from QUALCAST, TOPLINE, BECK/ARNLEY and 1 other brand. QUALCAST 307578 carries the "Popular" badge.

This group includes QUALCAST 307578, BECK/ARNLEY 0221234 and QUALCAST 307589 and the remaining parts above.

This table covers the Valve seats. Read more

6 Valve Seat parts for the 1991 Eagle Summit come from 3 brands — QUALCAST, SBI and DURA-BOND. The "Popular" part is QUALCAST 21112552.

Part numbers include QUALCAST 21112552, DURA-BOND 31048 and QUALCAST 21131262, among others listed above.

This table covers the keepers that lock each valve-spring retainer to the stem. Read more

This group shows a single part: SBI 1211031.

This table covers the seals on each valve stem that control oil into the guides. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

9 Valve Stem Seal parts are listed for the 1991 Eagle Summit, from ELRING, FEL-PRO, APEX and 6 other brands. ELRING 019790 carries the "Popular" badge.

This group includes ELRING 019790, FEL-PRO SS72805 and APEX AVS2002 and the remaining parts above.