2025 Ford Ranger Engine Parts

This table covers the front and rear seals that keep oil in at the crankshaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

One part is listed for the 2025 Ford Ranger — MAHLE / CLEVITE JV1754.

This table covers the head gaskets that seal the block to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

This group shows a single part: FEL-PRO 26941PT.

This table covers the Cylinder Head temperature sensors. Typical signs include hard cold starts, a fan that never comes on, or a gauge that disagrees with the scan tool. A sensor that reads open or shorted is usually the part; an implausible-but-smooth reading can be wiring. Read more

2 Cylinder Head Temperature Sensor parts are listed for the 2025 Ford Ranger, from STANDARD MOTOR PRODUCTS and WELLS.

This group includes STANDARD MOTOR PRODUCTS TX365 and WELLS 5S17577.

This table covers the Engine covers. Read more

This group shows a single part: TECHPRO FO1228206.

This table covers the exhaust valves that let combustion gas out of the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

3 Exhaust Valve parts are listed for the 2025 Ford Ranger, from MELLING, QUALCAST and SBI.

Listed part numbers: MELLING V3497, QUALCAST 1013497 and SBI 13481SN.

This table covers the Harmonic Balancer bolts. Read more

2 Harmonic Balancer Bolt parts are listed for the 2025 Ford Ranger, from DORMAN and SKP.

Listed part numbers: DORMAN 926885 and SKP SK926885.

This table covers the intake valves that let air (and fuel, on port-injected engines) into the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

4 Intake Valve parts are listed for the 2025 Ford Ranger, from SBI, ENGINETECH and MELLING.

Part numbers include ENGINETECH V2730, MELLING V3428 and SBI 13480, among others listed above.

This table covers the long-block engine assemblies (block, crank, heads). Read more

2 Long Block parts for the 2025 Ford Ranger come from MOTORCRAFT.

This group includes MOTORCRAFT RB3Z6006A and MOTORCRAFT N2DZ6006C.

This table covers the mounts that hold the engine to the chassis. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes. Read more

5 Motor Mount parts are listed for the 2025 Ford Ranger, from ANCHOR, DEA / MARMON RIDE CONTROL and WESTAR. ANCHOR 3715 carries the "Popular" badge.

Listed part numbers: ANCHOR 3715, ANCHOR 3716 and DEA / MARMON RIDE CONTROL A20190, plus the other parts above.

This table covers the engine oils listed by grade and specification for this engine. Typical signs include a low-oil lamp, knocking after a long interval, or oil that has gone thin and black well before the next service. Match the viscosity and spec in the notes (and on the filler cap). The tables group grades — they are not interchangeable. Read more

29 Oil parts are listed for the 2025 Ford Ranger, from VALVOLINE, MOBIL, LIQUI MOLY and 4 other brands. LIQUI MOLY 20228 carries the "Popular" badge. They are grouped as Full Synthetic, High Mileage (>75,000 Miles) and Synthetic Blend, with Full Synthetic the largest group at 19 parts from VALVOLINE, LIQUI MOLY, MOBIL and 4 other brands.

This table covers the heat exchangers that cool engine oil. Typical signs include oil at the cooler fittings, or coolant that looks like a milkshake. Pressure-test both circuits after a cooler swap — a leak here mixes oil and coolant. Read more

2 Oil Cooler parts are listed for the 2025 Ford Ranger, from DORMAN and MOTORCRAFT.

Listed part numbers: DORMAN 918625 and MOTORCRAFT YOC16.

This table covers the Oil Dipstick tubes. Read more

MOTORCRAFT supplies the 3 Oil Dipstick / Tube parts for the 2025 Ford Ranger.

Part numbers include MOTORCRAFT EDPS84, MOTORCRAFT EDPS42 and MOTORCRAFT EDPS74.

This table covers the drain plugs in the oil pan. Read more

DORMAN supplies the 5 Oil Drain Plug parts for the 2025 Ford Ranger.

Part numbers include DORMAN 090034, DORMAN 090175 and DORMAN 097826, among others listed above.

This table covers the caps on the oil filler neck. Read more

2 Oil Filler Cap parts are listed for the 2025 Ford Ranger, from MOTORAD and MOTORCRAFT.

Listed part numbers: MOTORAD MO201 and MOTORCRAFT EC791.

This table covers the oil filters that screw onto this engine's filter mount. Typical signs include low oil pressure after a service, or a filter that will not spin off because the old gasket stayed on the block. Lube the new gasket and tighten to the spec on the box; a double-gasket install dumps the sump on the first drive. Read more

41 Oil Filter parts are listed for the 2025 Ford Ranger, from FRAM, WIX, FVP and 11 other brands. PRO-TEC PXL10050 carries the "Popular" badge. Grades run from Economy through Standard Replacement; Standard Replacement is the most populated section, led by ACDELCO, MOTORCRAFT, WIX and 7 other brands.

This table covers the Oil Filter covers. Read more

2 Oil Filter Cover parts for the 2025 Ford Ranger come from 2 brands — DORMAN and MOTORAD.

Listed part numbers: DORMAN 921157 and MOTORAD MO363.

This table covers the oil pans that hold the engine's oil sump. Read more

This group shows a single part: SKP SK7A194.

This table covers the gaskets that seal the Oil Pump. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

2 Oil Pump Gasket parts for the 2025 Ford Ranger come from MOTORCRAFT.

Listed part numbers: MOTORCRAFT EEG1663 and MOTORCRAFT EEG1664.

This table covers the pickup tubes and screens that feed the oil pump. Read more

2 Oil Pump Pickup Tube / Screen parts for the 2025 Ford Ranger come from MOTORCRAFT.

Listed part numbers: MOTORCRAFT EPT2 and MOTORCRAFT EPT3.

This table covers the rocker arms that transfer cam motion to the valves. Read more

2 Rocker Arm parts are listed for the 2025 Ford Ranger, from INA and SBI.

Listed part numbers: INA VF02551 and SBI 1801342.

This table covers the Short blocks. Read more

This group shows a single part: MOTORCRAFT RB3Z6009A.

This table covers the timing chains that keep the cams in time with the crank. Read more

This group shows a single part: MELLING 959.

This table covers the guides and dampers that keep the timing chain on its path. Read more

2 Timing Chain Guide / Damper parts for the 2025 Ford Ranger come from MELLING.

Part numbers include MELLING BG7026 and MELLING BT7024.

This table covers the tensioners that keep the timing chain taut. Typical signs include belt flutter, a chirp that returns after a new belt, or an arm that no longer damps. Replace the tensioner with the belt at higher mileage. Read more

3 Timing Chain Tensioner parts are listed for the 2025 Ford Ranger, from MELLING and INA.

Part numbers include INA ZT0692, MELLING BT7026 and MELLING BT7025.

This table covers the seals at the Timing Cover. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

2 Timing Cover Seal parts are listed for the 2025 Ford Ranger, from MAHLE / CLEVITE and VICTOR REINZ.

This group includes MAHLE / CLEVITE 68024 and VICTOR REINZ 811049600.

This table covers the turbochargers that compress intake air. Read more

One part is listed for the 2025 Ford Ranger — GPD 2511865.

This table covers the Turbocharger Boost sensors. Typical signs include a warning lamp, a stored code, or a reading that drops out when the harness is wiggled. Inspect the connector and ground before replacing the sensor — wiring faults are often condemned as bad sensors. Read more

This group shows a single part: WELLS 5S15716.

This table covers the gaskets that seal the Turbocharger. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

This group shows a single part: GPD 2535105.

This table covers the Turbocharger Oil lines. Typical signs include a wet fitting, a rusted pipe, or a pressure loss in this circuit. Flare or thread the new line the way the notes specify; a kinked replacement will fail early. Read more

One part is listed for the 2025 Ford Ranger — MOTORCRAFT OSL36.

This table covers the Turbocharger Wastegate Solenoid actuators. Typical signs include a door or range that will not move, or a click with no motion. Confirm the command signal before replacing the actuator — a failed module looks the same. Read more

One part is listed for the 2025 Ford Ranger — BOSCH 0280751042.

This table covers the pressed-in bronze and cast-iron guides that align valve stems. Typical signs include oil smoke on startup, a guide that has gone oval, or a valve that no longer seats quietly. Guides are a machine-shop fit. Confirm stem diameter in the notes before ordering. Read more

One part is listed for the 2025 Ford Ranger — SBI 1403215.

This table covers the lifters / tappets that transfer cam motion to the valves. Read more

3 Valve Lifter parts are listed for the 2025 Ford Ranger, from ENGINETECH, SBI and SEALED POWER.

Part numbers include ENGINETECH L5000, SBI VL575 and SEALED POWER HT2314.

This table covers the Valve seats. Read more

2 Valve Seat parts for the 2025 Ford Ranger come from SBI.

Listed part numbers: SBI SB1140E1 and SBI SB1297E1.

This table covers the springs that close each intake and exhaust valve. Typical signs include a sagging corner, a broken coil, or a clunk from the spring pocket. Replace springs in axle pairs and inspect the seats. Read more

This group shows a single part: MELLING VS1666.

This table covers the Valve Spring retainers. Read more

2 Valve Spring Retainer parts for the 2025 Ford Ranger come from MELLING.

Listed part numbers: MELLING VSR715 and MELLING VSR714.

This table covers the keepers that lock each valve-spring retainer to the stem. Read more

5 Valve Spring Retainer Keeper parts for the 2025 Ford Ranger come from 3 brands — MELLING, SBI and ENGINETECH.

Part numbers include ENGINETECH EPF1140, MELLING VL1120 and MELLING VL1140, among others listed above.

This table covers the seals on each valve stem that control oil into the guides. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

SBI supplies the 3 Valve Stem Seal parts for the 2025 Ford Ranger.

Part numbers include SBI 1221410, SBI 1221411 and SBI 1221516.

This table covers the oil-control solenoids that command the cam phasers. Typical signs include a door or range that will not move, or a click with no motion. Confirm the command signal before replacing the actuator — a failed module looks the same. Read more

4 Variable Valve Timing (VVT) Solenoid / Actuator parts are listed for the 2025 Ford Ranger, from WELLS, STANDARD MOTOR PRODUCTS and GATES.

In the Economy grade, WELLS supplies 1 part: the catalog's value-priced group. A representative part number is WELLS 2T1193.

The Standard Replacement section lists 1 option from STANDARD MOTOR PRODUCTS — built to original-equipment specification. STANDARD MOTOR PRODUCTS VVT346 is listed in this group.

2 ungrouped parts are not assigned to a grade, with the same engine-level match.

Part numbers include WELLS 2T1193, STANDARD MOTOR PRODUCTS VVT346 and GATES VVS246, among others listed above.

This table covers the seals at the Variable Valve Timing (VVT) Solenoid Gasket. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

This group shows a single part: MAHLE / CLEVITE B33509.