2008 International Durastar Engine Parts

This table covers the Camshaft bearings. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

2 Camshaft Bearing parts are listed for the 2008 International Durastar, from DURA-BOND and ENGINE PRO.

Part numbers include DURA-BOND IN24 and ENGINE PRO 151996.

This table covers the bearings in the connecting-rod big ends. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

One part is listed for the 2008 International Durastar — KING ENGINE BEARINGS CR8038CP.

This table covers the head gaskets that seal the block to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

ELRING supplies both parts for the 2008 International Durastar.

This group includes ELRING 832600 and ELRING 832570.

This table covers the exhaust valves that let combustion gas out of the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

This group shows a single part: MELLING V2180.

This table covers the high-pressure oil pumps that fire HEUI diesel injectors. Typical signs include noise from the pump, no pressure, or fluid that never arrives at the outlet. Prime or fill the pump as the notes require. A dry start is a common way to kill a new unit. Read more

2 High Pressure Diesel Injection Oil Pump (HPOP) parts for the 2008 International Durastar come from STANDARD MOTOR PRODUCTS.

Listed part numbers: STANDARD MOTOR PRODUCTS HPI9 and STANDARD MOTOR PRODUCTS HPI14.

This table covers the seals at the High Pressure Oil Rail. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

2 High Pressure Oil Rail Seal parts for the 2008 International Durastar come from 2 brands — DORMAN and STANDARD MOTOR PRODUCTS.

Part numbers include DORMAN 2855102 and STANDARD MOTOR PRODUCTS SK168.

This table covers the intake valves that let air (and fuel, on port-injected engines) into the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

This group shows a single part: MELLING V2179.

This table covers the engine oils listed by grade and specification for this engine. Typical signs include a low-oil lamp, knocking after a long interval, or oil that has gone thin and black well before the next service. Match the viscosity and spec in the notes (and on the filler cap). The tables group grades — they are not interchangeable. Read more

2 Oil parts for the 2008 International Durastar come from VALVOLINE.

Part numbers include VALVOLINE 774038 and VALVOLINE 884940.

This table covers the heat exchangers that cool engine oil. Typical signs include oil at the cooler fittings, or coolant that looks like a milkshake. Pressure-test both circuits after a cooler swap — a leak here mixes oil and coolant. Read more

4 Oil Cooler parts for the 2008 International Durastar come from 3 brands — STANDARD MOTOR PRODUCTS, SKP and ULTRA-POWER.

This group includes SKP SK9045101, STANDARD MOTOR PRODUCTS OCK1 and STANDARD MOTOR PRODUCTS OCK3 and the remaining parts above.

This table covers the gaskets that seal the Oil Cooler. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

One part is listed for the 2008 International Durastar — STANDARD MOTOR PRODUCTS OCG1.

This table covers the drain plugs in the oil pan. Read more

This group shows a single part: DORMAN 090177.

This table covers the oil filters that screw onto this engine's filter mount. Typical signs include low oil pressure after a service, or a filter that will not spin off because the old gasket stayed on the block. Lube the new gasket and tighten to the spec on the box; a double-gasket install dumps the sump on the first drive. Read more

27 Oil Filter parts for the 2008 International Durastar come from 8 brands — WIX, HASTINGS / BALDWIN, FAMOUS BRAND and 5 other brands. The "Popular" part is WIX 57744XD. Grades run from Economy through Standard Replacement; Standard Replacement is the most populated section, led by HASTINGS / BALDWIN, WIX, DONALDSON and 2 other brands.

This table covers the Oil Filter covers. Read more

2 Oil Filter Cover parts are listed for the 2008 International Durastar, from DORMAN and MOTORAD.

Part numbers include DORMAN 904204 and MOTORAD MO357.

This table covers the Oil Filter Return tubes. Read more

This group shows a single part: DORMAN 904264.

This table covers the oil pans that hold the engine's oil sump. Read more

2 Oil Pan parts are listed for the 2008 International Durastar, from DORMAN and SPECTRA PREMIUM.

This group includes DORMAN 2645104 and SPECTRA PREMIUM DTP07A.

This table covers the Oil Temperature senders. Read more

One part is listed for the 2008 International Durastar — DORMAN 9047549.

This table covers the pushrods that transfer lifter motion to the rocker arms. Read more

One part is listed for the 2008 International Durastar — MELLING MPR662.

This table covers the turbochargers that compress intake air. Read more

8 Turbocharger parts for the 2008 International Durastar come from 3 brands — GPD, ROTOMASTER and STANDARD MOTOR PRODUCTS.

This group includes GPD 2511850, GPD 2511348 and GPD 2511897 and the remaining parts above.

This table covers the gaskets that seal the Turbocharger. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

One part is listed for the 2008 International Durastar — GPD 2535129.

This table covers the fasteners that mount the turbocharger. Read more

2 Turbocharger Mounting Hardware parts are listed for the 2008 International Durastar, from DORMAN and SKP.

This group includes DORMAN 904234 and SKP SK904234.

This table covers the Turbocharger Oil lines. Typical signs include a wet fitting, a rusted pipe, or a pressure loss in this circuit. Flare or thread the new line the way the notes specify; a kinked replacement will fail early. Read more

4 Turbocharger Oil Line parts for the 2008 International Durastar come from 3 brands — GATES, DORMAN and SUNSONG.

Part numbers include DORMAN 625210, GATES TL102 and GATES TL100, among others listed above.

This table covers the Turbocharger service kits. Read more

One part is listed for the 2008 International Durastar — ROTOMASTER A1320305N.

This table covers the Turbocharger Up pipes. Read more

4 Turbocharger Up Pipe parts are listed for the 2008 International Durastar, from DORMAN and ULTRA-POWER.

This group includes DORMAN 679023 and DORMAN 679024 and the remaining parts above.

This table covers the gaskets that seal the valve cover to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

2 Valve Cover Gasket parts for the 2008 International Durastar come from DORMAN.

Part numbers include DORMAN 904401 and DORMAN 2645115.

This table covers the springs that close each intake and exhaust valve. Typical signs include a sagging corner, a broken coil, or a clunk from the spring pocket. Replace springs in axle pairs and inspect the seats. Read more

MELLING supplies the 3 Valve Spring parts for the 2008 International Durastar.

In the High Performance grade, MELLING supplies 1 part: engineered beyond original-equipment specification. A representative part number is MELLING 466704.

The Standard Replacement section lists 1 option from MELLING — built to original-equipment specification. MELLING VS1458 is listed in this group.

1 ungrouped part is not assigned to a grade, with the same engine-level match.

This group includes MELLING 466704, MELLING VS1458 and MELLING VS1190.

This table covers the keepers that lock each valve-spring retainer to the stem. Read more

One part is listed for the 2008 International Durastar — MELLING VL300.