2012 International Paystar Engine Parts

This table covers the Barometric pressure sensors. Typical signs include a check-engine light for MAP or fuel-rail pressure, or a limp mode under load. A vacuum leak or a clogged reference line will fake a bad pressure sensor. Read more

This group shows a single part: DORMAN 9047128.

This table covers the drain plugs in the oil pan. Read more

One part is listed for the 2012 International Paystar — DORMAN 0905003.

This table covers the crush washers and gaskets under the oil drain plug. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

This group shows a single part: DORMAN 0955003.

This table covers the oil filters that screw onto this engine's filter mount. Typical signs include low oil pressure after a service, or a filter that will not spin off because the old gasket stayed on the block. Lube the new gasket and tighten to the spec on the box; a double-gasket install dumps the sump on the first drive. Read more

8 Oil Filter parts are listed for the 2012 International Paystar, from WIX, HASTINGS / BALDWIN and DONALDSON. WIX 57746XD carries the "Popular" badge.

In the High Performance / Heavy Duty grade, WIX supplies 2 parts: grouped under the catalog's "High Performance / Heavy Duty" designation — the notes column spells out what sets them apart. A representative part number is WIX 57746XD.

The Standard Replacement section lists 4 options from HASTINGS / BALDWIN and DONALDSON — built to original-equipment specification. HASTINGS / BALDWIN BD50000 is listed in this group.

2 ungrouped parts are not assigned to a grade, with the same engine-level match.

Part numbers include WIX 57746XD, WIX WL10005XD and HASTINGS / BALDWIN BD50000, among others listed above.

This table covers the oil pans that hold the engine's oil sump. Read more

2 Oil Pan parts for the 2012 International Paystar come from 2 brands — DORMAN and SPECTRA PREMIUM.

Part numbers include DORMAN 2646005 and SPECTRA PREMIUM CMP05A.

This table covers the gaskets between the oil pan and the block. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

One part is listed for the 2012 International Paystar — DORMAN 2646005G.

This table covers the Oil Temperature senders. Read more

This group shows a single part: HOLSTEIN 2OTS0002.

This table covers the Timing Belt tensioners. Typical signs include belt flutter, a chirp that returns after a new belt, or an arm that no longer damps. Replace the tensioner with the belt at higher mileage. Read more

One part is listed for the 2012 International Paystar — SKP SK89448.

This table covers the turbochargers that compress intake air. Read more

7 Turbocharger parts are listed for the 2012 International Paystar, from GPD and ROTOMASTER.

Listed part numbers: GPD 2511538, GPD 2511890 and GPD 2511800, plus the other parts above.

This table covers the Turbocharger Boost sensors. Typical signs include a warning lamp, a stored code, or a reading that drops out when the harness is wiggled. Inspect the connector and ground before replacing the sensor — wiring faults are often condemned as bad sensors. Read more

This group shows a single part: DORMAN 9047130.

This table covers the gaskets that seal the Turbocharger. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

4 Turbocharger Gasket parts for the 2012 International Paystar come from 2 brands — DORMAN and DAYTON.

This group includes DAYTON 6745001G, DORMAN 6749044 and DORMAN 6749018 and the remaining parts above.

This table covers the Turbocharger speed sensors. Typical signs include a dead speedometer, harsh transmission shifts, or a code for vehicle speed. Inspect the tone wheel and the connector before replacing the sensor. Read more

This group shows a single part: DORMAN 9047111.

This table covers the springs that close each intake and exhaust valve. Typical signs include a sagging corner, a broken coil, or a clunk from the spring pocket. Replace springs in axle pairs and inspect the seats. Read more

This group shows a single part: MELLING VS1479.