1972 Jensen Interceptor Engine Parts

This table covers the Bolt kits. Read more

This group shows a single part: ARP 5459701.

This table covers the bearings in the connecting-rod big ends. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

6 Connecting Rod Bearing parts for the 1972 Jensen Interceptor come from KING ENGINE BEARINGS. The "Popular" part is KING ENGINE BEARINGS CR806HPND. Every part fits both the 6.3L V8 and the 7.2L V8.

The High Performance section lists 5 options from KING ENGINE BEARINGS — engineered beyond original-equipment specification. KING ENGINE BEARINGS CR806HPND is listed in this group.

In the Standard Replacement grade, KING ENGINE BEARINGS supplies 1 part: built to original-equipment specification. A representative part number is KING ENGINE BEARINGS CR806AM.

Part numbers include KING ENGINE BEARINGS CR806HPND, KING ENGINE BEARINGS CR806HPNDX and KING ENGINE BEARINGS CR806XPND, among others listed above.

This table covers the main bearings that support the crankshaft in the block. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

KING ENGINE BEARINGS supplies the 6 Crankshaft Main Bearing parts for the 1972 Jensen Interceptor.

High Performance: 2 parts, from KING ENGINE BEARINGS. A representative part number is KING ENGINE BEARINGS MB555HP.

The Standard Replacement section: 1 option from KING ENGINE BEARINGS. KING ENGINE BEARINGS MB555AM is listed in this group.

3 ungrouped parts are not assigned to a grade, with the same engine-level match.

Listed part numbers: KING ENGINE BEARINGS MB555HP, KING ENGINE BEARINGS MB555HPX and KING ENGINE BEARINGS MB555AM, plus the other parts above.

This table covers the sleeves used to restore a grooved crankshaft seal surface. Read more

2 Crankshaft Repair Sleeve parts are listed for the 1972 Jensen Interceptor, from NATIONAL and WJB / INMOTION PARTS. All of them fit every engine offered in the 1972 Interceptor.

This group includes NATIONAL 99218 and WJB / INMOTION PARTS WS99218.

This table covers the front and rear seals that keep oil in at the crankshaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

6 Crankshaft Seal parts are listed for the 1972 Jensen Interceptor, from FEL-PRO, NATIONAL, BCA and 3 other brands. FEL-PRO BS40240 carries the "Popular" badge. All of them fit every engine offered in the 1972 Interceptor.

Listed part numbers: FEL-PRO BS40240, NATIONAL 3103 and BCA NS3103, plus the other parts above.

This table covers the bolts that clamp the cylinder head to the block. Read more

2 Cylinder Head Bolt parts for the 1972 Jensen Interceptor come from ARP. Every part fits both the 6.3L V8 and the 7.2L V8.

Listed part numbers: ARP 1453606 and ARP 4453706.

This table covers the head gaskets that seal the block to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

3 Cylinder Head Gasket parts for the 1972 Jensen Interceptor come from 3 brands — FEL-PRO, MAHLE / CLEVITE and VICTOR REINZ. Every part fits both the 6.3L V8 and the 7.2L V8.

Part numbers include FEL-PRO 8519PT1, MAHLE / CLEVITE 3464VC and VICTOR REINZ 611033200.

This table covers multi-piece gasket sets for a cylinder-head job. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

3 Cylinder Head Gasket Set parts for the 1972 Jensen Interceptor come from 3 brands — FEL-PRO, MAHLE / CLEVITE and VICTOR REINZ. Every part fits both the 6.3L V8 and the 7.2L V8.

Listed part numbers: FEL-PRO HS7891PT11, MAHLE / CLEVITE HS3464VC and VICTOR REINZ 021032301.

This table covers the Cylinder Head Spacer shims. Read more

2 Cylinder Head Spacer Shim parts for the 1972 Jensen Interceptor come from 2 brands — MAHLE / CLEVITE and VICTOR REINZ. Every part fits both the 6.3L V8 and the 7.2L V8.

Listed part numbers: MAHLE / CLEVITE 55153 and VICTOR REINZ 711638300.

This table covers full gasket kits covering the joints opened in an engine rebuild. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

4 Engine Kit Gasket Set parts for the 1972 Jensen Interceptor come from 4 brands — ENGINE PRO, FEL-PRO, MAHLE / CLEVITE and 1 other brand. Every part fits both the 6.3L V8 and the 7.2L V8.

This group includes ENGINE PRO 311010MLS, FEL-PRO FS7891PT11 and MAHLE / CLEVITE 953344 and the remaining parts above.

This table covers the crankshaft pulleys / harmonic balancers at the front of the engine. Read more

This group shows a single part: ENGINE PRO PB1112ST.

This table covers the Harmonic Balancer bolts. Read more

One part is listed for the 1972 Jensen Interceptor — ARP 2402501.

This table covers the Intake Manifold bolts. Read more

This group shows a single part: ARP 1442001.

This table covers the gaskets between the intake manifold and the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

8 Intake Manifold Gasket parts for the 1972 Jensen Interceptor come from 3 brands — FEL-PRO, VICTOR REINZ and MAHLE / CLEVITE. The "Popular" part is FEL-PRO MS90175. 2 parts fit every engine; the other 6 are engine-specific.

Listed part numbers: FEL-PRO MS90175, FEL-PRO MS96007 and FEL-PRO MS96000, plus the other parts above.

This table covers the crush washers and gaskets under the oil drain plug. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

3 Oil Drain Plug Gasket parts for the 1972 Jensen Interceptor come from 3 brands — FEL-PRO, MAHLE / CLEVITE and VICTOR REINZ. Every part fits both the 6.3L V8 and the 7.2L V8.

Part numbers include FEL-PRO 70822, MAHLE / CLEVITE 2051 and VICTOR REINZ 711346200.

This table covers the oil filters that screw onto this engine's filter mount. Typical signs include low oil pressure after a service, or a filter that will not spin off because the old gasket stayed on the block. Lube the new gasket and tighten to the spec on the box; a double-gasket install dumps the sump on the first drive. Read more

16 Oil Filter parts are listed for the 1972 Jensen Interceptor, from FRAM, WIX, CHAMP / LUBER-FINER and 9 other brands. WIX 51515XP carries the "Popular" badge. 9 parts fit every engine; the other 7 are engine-specific.

In the Economy grade, CHAMP / LUBER-FINER, FRAM, FVP and 3 other brands supply 6 parts: the catalog's value-priced group. A representative part number is CHAMP / LUBER-FINER PH8A.

In the High Performance / Heavy Duty grade, WIX, FRAM and MOBIL supply 3 parts: grouped under the catalog's "High Performance / Heavy Duty" designation — the notes column spells out what sets them apart. A representative part number is WIX 51515XP.

The Standard Replacement section: 7 options from FRAM, MOTORCRAFT, WIX and 3 other brands. MOTORCRAFT FL1A is listed in this group.

This table covers the gaskets between the oil pan and the block. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

5 Oil Pan Gasket parts are listed for the 1972 Jensen Interceptor, from MAHLE / CLEVITE, FEL-PRO, ENGINE PRO and 1 other brand. FEL-PRO OS11729C1 carries the "Popular" badge. All of them fit every engine offered in the 1972 Interceptor.

Part numbers include FEL-PRO OS11729C1, ENGINE PRO 317345WT and MAHLE / CLEVITE OS31416, among others listed above.

This table covers the gaskets that seal the Oil Pressure Relief Valve. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

2 Oil Pressure Relief Valve Gasket parts for the 1972 Jensen Interceptor come from 2 brands — FEL-PRO and VICTOR REINZ. Every part fits both the 6.3L V8 and the 7.2L V8.

Listed part numbers: FEL-PRO 3122 and VICTOR REINZ 711456300.

This table covers the gaskets that seal the Oil Pump. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

This group shows a single part: MAHLE / CLEVITE B45558.

This table covers the gaskets that seal the Timing Cover. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

4 Timing Cover Gasket parts are listed for the 1972 Jensen Interceptor, from MAHLE / CLEVITE, FEL-PRO and VICTOR REINZ. All of them fit every engine offered in the 1972 Interceptor.

Listed part numbers: FEL-PRO TCS124602, MAHLE / CLEVITE T18750 and MAHLE / CLEVITE JV834, plus the other parts above.

This table covers the seals at the Timing Cover. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

One part is listed for the 1972 Jensen Interceptor — MAHLE / CLEVITE 64573.

This table covers the gaskets that seal the valve cover to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

7 Valve Cover Gasket parts are listed for the 1972 Jensen Interceptor, from VICTOR REINZ, FEL-PRO and MAHLE / CLEVITE. FEL-PRO VS13379 carries the "Popular" badge. All of them fit every engine offered in the 1972 Interceptor.

This group includes FEL-PRO VS13379, FEL-PRO VS50145R and MAHLE / CLEVITE VS38322 and the remaining parts above.

This table covers the seals on each valve stem that control oil into the guides. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

8 Valve Stem Seal parts are listed for the 1972 Jensen Interceptor, from FEL-PRO, MAHLE / CLEVITE and VICTOR REINZ. FEL-PRO SS12764 carries the "Popular" badge. 2 parts fit every engine; the other 6 are engine-specific.

Part numbers include FEL-PRO SS12764, FEL-PRO SS70014 and FEL-PRO SS12419, among others listed above.