2022 Kia Stinger Engine Parts

This table covers the bearings in the connecting-rod big ends. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

2 Connecting Rod Bearing parts for the 2022 Kia Stinger come from TOPLINE.

Listed part numbers: TOPLINE RBHY27 and TOPLINE RBHY14L.

This table covers lower / conversion gasket sets for oil-pan and related joints. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

2 Conversion / Lower Gasket Set parts for the 2022 Kia Stinger come from 2 brands — AJUSA and TOPLINE.

Part numbers include AJUSA 54350800 and TOPLINE CBSHY27.

This table covers the main bearings that support the crankshaft in the block. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

TOPLINE supplies the 4 Crankshaft Main Bearing parts for the 2022 Kia Stinger.

This group includes TOPLINE TWHY27, TOPLINE MBHY27 and TOPLINE TWHY14 and the remaining parts above.

This table covers the front and rear seals that keep oil in at the crankshaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

7 Crankshaft Seal parts are listed for the 2022 Kia Stinger, from ELRING, MAHLE / CLEVITE, AJUSA and 1 other brand. MAHLE / CLEVITE 67874 carries the "Popular" badge.

Listed part numbers: MAHLE / CLEVITE 67874, AJUSA 15048600 and ELRING 827070, plus the other parts above.

This table covers the bolts that clamp the cylinder head to the block. Read more

2 Cylinder Head Bolt parts for the 2022 Kia Stinger come from 2 brands — AJUSA and TOPLINE.

Listed part numbers: AJUSA 81056400 and TOPLINE HBHY27.

This table covers the head gaskets that seal the block to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

4 Cylinder Head Gasket parts for the 2022 Kia Stinger come from AJUSA.

This group includes AJUSA 10284100, AJUSA 10284200 and AJUSA 52689500 and the remaining parts above.

This table covers multi-piece gasket sets for a cylinder-head job. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

2 Cylinder Head Gasket Set parts for the 2022 Kia Stinger come from 2 brands — AJUSA and TOPLINE.

Listed part numbers: AJUSA 52689400 and TOPLINE HSHY27GT.

This table covers full gasket kits covering the joints opened in an engine rebuild. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

2 Engine Kit Gasket Set parts for the 2022 Kia Stinger come from 2 brands — AJUSA and TOPLINE.

Listed part numbers: AJUSA 50609700 and TOPLINE CGSHY27GT.

This table covers the exhaust valves that let combustion gas out of the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

One part is listed for the 2022 Kia Stinger — TOPLINE EVHY27.

This table covers the crankshaft pulleys / harmonic balancers at the front of the engine. Read more

This group shows a single part: HL MANDO 30A5029.

This table covers the gaskets between the intake manifold and the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

4 Intake Manifold Gasket parts for the 2022 Kia Stinger come from 3 brands — AJUSA, ELRING and MAHLE / CLEVITE.

This group includes AJUSA 02025900, AJUSA 13362100 and ELRING 827250 and the remaining parts above.

This table covers the intake valves that let air (and fuel, on port-injected engines) into the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

4 Intake Valve parts are listed for the 2022 Kia Stinger, from TOPLINE, MELLING and SBI.

This group includes MELLING V3286, SBI 13286 and TOPLINE IVHY27 and the remaining parts above.

This table covers the engine oils listed by grade and specification for this engine. Typical signs include a low-oil lamp, knocking after a long interval, or oil that has gone thin and black well before the next service. Match the viscosity and spec in the notes (and on the filler cap). The tables group grades — they are not interchangeable. Read more

28 Oil parts are listed for the 2022 Kia Stinger, from MOBIL, LIQUI MOLY, IDEMITSU and 3 other brands. MOBIL 125195 carries the "Popular" badge. Full Synthetic, High Mileage (>75,000 Miles) and Synthetic Blend are all represented, and Full Synthetic alone accounts for 15 parts.

This table covers the drain plugs in the oil pan. Read more

4 Oil Drain Plug parts are listed for the 2022 Kia Stinger, from DORMAN, REIN and SKP.

This group includes DORMAN 090033, DORMAN 090053 and REIN HWU0110 and the remaining parts above.

This table covers the crush washers and gaskets under the oil drain plug. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

3 Oil Drain Plug Gasket parts for the 2022 Kia Stinger come from 2 brands — DORMAN and AJUSA. 2 parts fit every engine; the other 1 is engine-specific.

Listed part numbers: AJUSA 22007100, DORMAN 095147 and DORMAN 995147CD.

This table covers the caps on the oil filler neck. Read more

4 Oil Filler Cap parts are listed for the 2022 Kia Stinger, from CALORSTAT, GATES, MOTORAD and 1 other brand. 1 part fits every engine; the other 3 are engine-specific.

This group includes CALORSTAT OC2331, GATES 31083 and MOTORAD MO151 and the remaining parts above.

This table covers the oil filters that screw onto this engine's filter mount. Typical signs include low oil pressure after a service, or a filter that will not spin off because the old gasket stayed on the block. Lube the new gasket and tighten to the spec on the box; a double-gasket install dumps the sump on the first drive. Read more

12 Oil Filter parts are listed for the 2022 Kia Stinger, from CHAMP / LUBER-FINER, VARIOUS MFR, WIX and 6 other brands. VARIOUS MFR PO99470EX carries the "Popular" badge.

In the Economy grade, CHAMP / LUBER-FINER, FAMOUS BRAND, PRO-TEC and 1 other brand supply 5 parts: the catalog's value-priced group. A representative part number is CHAMP / LUBER-FINER P1100.

The Standard Replacement section lists 7 options from VARIOUS MFR, WIX, BECK/ARNLEY and 2 other brands — built to original-equipment specification. VARIOUS MFR PO99470EX is listed in this group.

This table covers the Oil Filter Adapter Gasket O-rings. Typical signs include a seep at a fitting or a housing that weeps after a service. Lube the new O-ring with the fluid it will see, and do not roll it into the groove. Read more

This group shows a single part: MAHLE / CLEVITE B33332.

This table covers the Oil Filter covers. Read more

This group shows a single part: ACKOJA A520915.

This table covers the seals at the Oil Filter Housing. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

One part is listed for the 2022 Kia Stinger — MAHLE / CLEVITE GS33924.

This table covers the chains that drive the oil pump. Read more

3 Oil Pump Chain parts for the 2022 Kia Stinger come from 3 brands — CLOYES, MELLING and S.A. GEAR.

This group includes CLOYES C557, MELLING 1103 and S.A. GEAR C1239.

This table covers the Oil Pump Chain tensioners. Typical signs include belt flutter, a chirp that returns after a new belt, or an arm that no longer damps. Replace the tensioner with the belt at higher mileage. Read more

3 Oil Pump Chain Tensioner parts are listed for the 2022 Kia Stinger, from CLOYES, MELLING and S.A. GEAR.

This group includes CLOYES 96259, MELLING BT7081 and S.A. GEAR 91421.

This table covers the Oil Pump sprockets. Read more

This group shows a single part: MELLING S1327.

This table covers the pistons that travel in each cylinder. Typical signs include knock, blow-by, or a cylinder that will not hold compression. Piston work is a short-block job. Match bore, pin and ring pack in the notes — not the photo. Read more

This group shows a single part: TOPLINE PAHY27T.

This table covers the Piston Pin bushings. Typical signs include a clunk over bumps, or a torn or walked-out bushing you can see. Press the new bushing square. A cocked bushing will tear in a few thousand miles. Read more

One part is listed for the 2022 Kia Stinger — TOPLINE PBHY27T.

This table covers the rings that seal each piston to the cylinder wall. Read more

This group shows a single part: TOPLINE RSHY27T.

This table covers the timing chains that keep the cams in time with the crank. Read more

4 Timing Chain parts for the 2022 Kia Stinger come from 3 brands — MELLING, CLOYES and S.A. GEAR.

Part numbers include CLOYES C555, MELLING 1101 and MELLING 1098, among others listed above.

This table covers kits that group a timing chain with the related tensioners and guides. Read more

5 Timing Chain & Component Kit parts are listed for the 2022 Kia Stinger, from MELLING, S.A. GEAR and CLOYES.

Economy: 1 part, from S.A. GEAR. A representative part number is S.A. GEAR 76483S.

The Standard Replacement section: 3 options from MELLING and CLOYES. CLOYES 90555SGX is listed in this group.

1 ungrouped part is not assigned to a grade, with the same engine-level match.

Part numbers include S.A. GEAR 76483S, CLOYES 90555SGX and MELLING 31098SX, among others listed above.

This table covers the guides and dampers that keep the timing chain on its path. Read more

12 Timing Chain Guide / Damper parts for the 2022 Kia Stinger come from 5 brands — CLOYES, MELLING, S.A. GEAR and 2 other brands. The "Popular" part is S.A. GEAR 71283. 1 part fits every engine; the other 11 are engine-specific.

This table covers the tensioners that keep the timing chain taut. Typical signs include belt flutter, a chirp that returns after a new belt, or an arm that no longer damps. Replace the tensioner with the belt at higher mileage. Read more

7 Timing Chain Tensioner parts are listed for the 2022 Kia Stinger, from MELLING, HYUNDAI, S.A. GEAR and 3 other brands. HYUNDAI 244103CGA3 carries the "Popular" badge.

Part numbers include HYUNDAI 244103CGA3, S.A. GEAR 91378 and CLOYES 96252, among others listed above.

This table covers the gaskets that seal the Timing Cover. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

2 Timing Cover Gasket parts are listed for the 2022 Kia Stinger, from ELRING and MAHLE / CLEVITE.

This group includes ELRING 935810 and MAHLE / CLEVITE JV5274.

This table covers the crankshaft sprockets that drive the timing chain or belt. Read more

5 Timing Crank Sprocket parts are listed for the 2022 Kia Stinger, from MELLING and HYUNDAI.

This group includes HYUNDAI 231213L100, MELLING S1332 and MELLING S1328 and the remaining parts above.

This table covers the Turbocharger Boost sensors. Typical signs include a warning lamp, a stored code, or a reading that drops out when the harness is wiggled. Inspect the connector and ground before replacing the sensor — wiring faults are often condemned as bad sensors. Read more

This group shows a single part: WELLS 5S15729.

This table covers the gaskets that seal the Turbocharger. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

2 Turbocharger Gasket parts for the 2022 Kia Stinger come from AJUSA.

This group includes AJUSA JTC12891 and AJUSA JTC12892.

This table covers the Turbocharger Oil lines. Typical signs include a wet fitting, a rusted pipe, or a pressure loss in this circuit. Flare or thread the new line the way the notes specify; a kinked replacement will fail early. Read more

One part is listed for the 2022 Kia Stinger — AJUSA OP11249.

This table covers the gaskets that seal the valve cover to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

5 Valve Cover Gasket parts are listed for the 2022 Kia Stinger, from AJUSA, BECK/ARNLEY and MAHLE / CLEVITE. MAHLE / CLEVITE VS50879 carries the "Popular" badge.

Part numbers include MAHLE / CLEVITE VS50879, AJUSA 11156100 and AJUSA 11156200, among others listed above.

This table covers the pressed-in bronze and cast-iron guides that align valve stems. Typical signs include oil smoke on startup, a guide that has gone oval, or a valve that no longer seats quietly. Guides are a machine-shop fit. Confirm stem diameter in the notes before ordering. Read more

4 Valve Guide parts are listed for the 2022 Kia Stinger, from TOPLINE, QUALCAST and SBI.

This group includes QUALCAST 303152, SBI 1403152 and TOPLINE VGHY27 and the remaining parts above.

This table covers the lifters / tappets that transfer cam motion to the valves. Read more

2 Valve Lifter parts are listed for the 2022 Kia Stinger, from HYUNDAI and TOPLINE.

Part numbers include HYUNDAI 222263CCC0 and TOPLINE LIFHY23.

This table covers the keepers that lock each valve-spring retainer to the stem. Read more

3 Valve Spring Retainer Keeper parts for the 2022 Kia Stinger come from 3 brands — MELLING, QUALCAST and SBI. Every part fits both the 2.5L L4 Turbocharged and the 3.3L V6 Turbocharged.

Part numbers include MELLING VL1060, QUALCAST 345008 and SBI 1211060.

This table covers the seals on each valve stem that control oil into the guides. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

9 Valve Stem Seal parts are listed for the 2022 Kia Stinger, from AJUSA, TOPLINE, FEL-PRO and 4 other brands. AJUSA 12025500 carries the "Popular" badge.

Listed part numbers: AJUSA 12025500, FEL-PRO SS72298 and AJUSA 57062800, plus the other parts above.

This table covers the oil-control solenoids that command the cam phasers. Typical signs include a door or range that will not move, or a click with no motion. Confirm the command signal before replacing the actuator — a failed module looks the same. Read more

11 Variable Valve Timing (VVT) Solenoid / Actuator parts are listed for the 2022 Kia Stinger, from HYUNDAI, STANDARD MOTOR PRODUCTS, HOLSTEIN and 2 other brands. HYUNDAI 243603CAA2 carries the "Popular" badge.

Economy: 3 parts, from HOLSTEIN and WELLS. A representative part number is HOLSTEIN 2VTS0330.

The Standard Replacement section: 7 options from HYUNDAI, CLOYES and STANDARD MOTOR PRODUCTS. HYUNDAI 243603CAA2 is listed in this group.

1 ungrouped part is not assigned to a grade, with the same engine-level match.

This table covers the cam phaser sprockets used by the variable-valve-timing system. Read more

5 Variable Valve Timing (VVT) Sprocket parts are listed for the 2022 Kia Stinger, from HYUNDAI, SKP, AUTOTECNICA and 1 other brand. SKP SK998015 carries the "Popular" badge.

Economy: 2 parts, from SKP and AUTOTECNICA. A representative part number is SKP SK998015.

The Standard Replacement section: 3 options from HYUNDAI and PREFERRED COMPONENTS INC. HYUNDAI 243503L100 is listed in this group.

Listed part numbers: SKP SK998015, AUTOTECNICA HY1421805 and HYUNDAI 243503L100, plus the other parts above.