2018 Nissan Murano Engine Parts

This table covers the connecting rods between each piston and the crankshaft. Read more

This group shows a single part: TOPLINE CRD41.

This table covers the bearings in the connecting-rod big ends. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

4 Connecting Rod Bearing parts for the 2018 Nissan Murano come from 2 brands — KING ENGINE BEARINGS and TOPLINE.

The High Performance section lists 2 options from KING ENGINE BEARINGS — engineered beyond original-equipment specification. KING ENGINE BEARINGS CR6775XP is listed in this group.

In the Standard Replacement grade, KING ENGINE BEARINGS and TOPLINE supply 2 parts: built to original-equipment specification. A representative part number is KING ENGINE BEARINGS CR6775CP.

Part numbers include KING ENGINE BEARINGS CR6775XP, KING ENGINE BEARINGS CR6775XPX and KING ENGINE BEARINGS CR6775CP, among others listed above.

This table covers lower / conversion gasket sets for oil-pan and related joints. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

5 Conversion / Lower Gasket Set parts for the 2018 Nissan Murano come from 5 brands — FEL-PRO, AJUSA, APEX and 2 other brands. The "Popular" part is FEL-PRO CS26511.

Part numbers include FEL-PRO CS26511, AJUSA 54270200 and APEX ACS5062, among others listed above.

This table covers the main bearings that support the crankshaft in the block. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

5 Crankshaft Main Bearing parts are listed for the 2018 Nissan Murano, from KING ENGINE BEARINGS and TOPLINE. TOPLINE TWD34 carries the "Popular" badge.

High Performance: 2 parts, from KING ENGINE BEARINGS. A representative part number is KING ENGINE BEARINGS MB4058XPX.

The Standard Replacement section: 3 options from TOPLINE and KING ENGINE BEARINGS. TOPLINE TWD34 is listed in this group.

Part numbers include TOPLINE TWD34, KING ENGINE BEARINGS MB4058XPX and KING ENGINE BEARINGS MB4058XP, among others listed above.

This table covers the sleeves used to restore a grooved crankshaft seal surface. Read more

3 Crankshaft Repair Sleeve parts are listed for the 2018 Nissan Murano, from BCA, NATIONAL and WJB / INMOTION PARTS.

This group includes BCA NS99189, NATIONAL 99189 and WJB / INMOTION PARTS WS99189.

This table covers the front and rear seals that keep oil in at the crankshaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

12 Crankshaft Seal parts are listed for the 2018 Nissan Murano, from WJB / INMOTION PARTS, NATIONAL, BCA and 7 other brands. BCA NS710356 carries the "Popular" badge.

This table covers the bolts that clamp the cylinder head to the block. Read more

6 Cylinder Head Bolt parts for the 2018 Nissan Murano come from 6 brands — AJUSA, APEX, BECK/ARNLEY and 3 other brands. The "Popular" part is AJUSA 81047800.

Part numbers include AJUSA 81047800, APEX AHB534 and BECK/ARNLEY 0161026, among others listed above.

This table covers the head gaskets that seal the block to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

13 Cylinder Head Gasket parts for the 2018 Nissan Murano come from 7 brands — APEX, FEL-PRO, AJUSA and 4 other brands. The "Popular" part is APEX AHG562L.

This table covers multi-piece gasket sets for a cylinder-head job. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

5 Cylinder Head Gasket Set parts for the 2018 Nissan Murano come from 3 brands — ENGINETECH, FEL-PRO and APEX. The "Popular" part is ENGINETECH NI35HSD.

Listed part numbers: ENGINETECH NI35HSD, APEX AHS5062 and ENGINETECH NI35HSDWB, plus the other parts above.

This table covers the block heaters that warm the coolant or oil in cold weather. Read more

KAT'S HEATERS supplies the 3 Engine Block Heater parts for the 2018 Nissan Murano.

This group includes KAT'S HEATERS 16600, KAT'S HEATERS 11412 and KAT'S HEATERS 28500.

This table covers the Engine covers. Read more

3 Engine Cover parts for the 2018 Nissan Murano come from 2 brands — TECHPRO and VARIOUS MFR.

This group includes TECHPRO NI1228165 and TECHPRO NI1228166 and the remaining parts above.

This table covers full gasket kits covering the joints opened in an engine rebuild. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

2 Engine Kit Gasket Set parts for the 2018 Nissan Murano come from 2 brands — AJUSA and TOPLINE.

Listed part numbers: AJUSA 50464600 and TOPLINE CGSD41A.

This table covers the exhaust valves that let combustion gas out of the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

3 Exhaust Valve parts are listed for the 2018 Nissan Murano, from ENGINETECH, SBI and TOPLINE.

This group includes ENGINETECH EM4475, SBI 13221 and TOPLINE EVD41HRL.

This table covers the crankshaft pulleys / harmonic balancers at the front of the engine. Read more

3 Harmonic Balancer parts for the 2018 Nissan Murano come from 3 brands — ATP, DAYCO and DORMAN.

This group includes ATP 102385, DAYCO PB1682N and DORMAN 594433.

This table covers the gaskets between the intake manifold and the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

5 Intake Manifold Gasket parts for the 2018 Nissan Murano come from 5 brands — MAHLE / CLEVITE, AJUSA, APEX and 2 other brands. The "Popular" part is MAHLE / CLEVITE MS19450.

This group includes MAHLE / CLEVITE MS19450, AJUSA 13261900 and APEX AMS5621 and the remaining parts above.

This table covers the Intake Manifold Runner Control Valve solenoids. Typical signs include a harsh or missing shift, or a code for this solenoid circuit. Check resistance and the connector before dropping the pan for a solenoid. Read more

3 Intake Manifold Runner Control Valve / Solenoid parts for the 2018 Nissan Murano come from 3 brands — DORMAN, STANDARD MOTOR PRODUCTS and ULTRA-POWER.

Listed part numbers: DORMAN 911506 and STANDARD MOTOR PRODUCTS RCS103, plus the other parts above.

This table covers the gaskets that seal the Intake Plenum. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

4 Intake Plenum Gasket parts are listed for the 2018 Nissan Murano, from AJUSA, APEX, FEL-PRO and 1 other brand.

This group includes AJUSA 01291300, APEX AMS5620 and FEL-PRO MS97220 and the remaining parts above.

This table covers the intake valves that let air (and fuel, on port-injected engines) into the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

One part is listed for the 2018 Nissan Murano — TOPLINE IVD41HRL.

This table covers the mounts that hold the engine to the chassis. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes. Read more

23 Motor Mount parts are listed for the 2018 Nissan Murano, from ANCHOR, WESTAR, PIONEER and 3 other brands. SKP SKMA4365HY carries the "Popular" badge.

In the Economy grade, SKP supplies 2 parts: the catalog's value-priced group. A representative part number is SKP SKMA4365HY.

The Standard Replacement section: 21 options from ANCHOR, WESTAR, PIONEER and 2 other brands. ANCHOR 9808 is listed in this group.

This table covers the Motor Mount kits. Read more

ANCHOR supplies both parts for the 2018 Nissan Murano.

This group includes ANCHOR 300211 and ANCHOR 300307.

This table covers the engine oils listed by grade and specification for this engine. Typical signs include a low-oil lamp, knocking after a long interval, or oil that has gone thin and black well before the next service. Match the viscosity and spec in the notes (and on the filler cap). The tables group grades — they are not interchangeable. Read more

37 Oil parts are listed for the 2018 Nissan Murano, from LIQUI MOLY, VALVOLINE, MOBIL and 3 other brands. LIQUI MOLY 22044 carries the "Popular" badge. They are grouped as Full Synthetic and High Mileage (>75,000 Miles), with Full Synthetic the largest group at 30 parts from LIQUI MOLY, VALVOLINE, MOBIL and 3 other brands.

This table covers the heat exchangers that cool engine oil. Typical signs include oil at the cooler fittings, or coolant that looks like a milkshake. Pressure-test both circuits after a cooler swap — a leak here mixes oil and coolant. Read more

2 Oil Cooler parts are listed for the 2018 Nissan Murano, from ACKOJA and STANDARD MOTOR PRODUCTS.

Part numbers include ACKOJA A38600022 and STANDARD MOTOR PRODUCTS OCK78.

This table covers the seals at the Oil Cooler. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

3 Oil Cooler Seal parts for the 2018 Nissan Murano come from 2 brands — FEL-PRO and MAHLE / CLEVITE.

This group includes FEL-PRO 72493, FEL-PRO 71863 and MAHLE / CLEVITE B33344.

This table covers the Oil Dipstick tubes. Read more

2 Oil Dipstick / Tube parts are listed for the 2018 Nissan Murano, from AUTOTECNICA and DORMAN.

This group includes AUTOTECNICA NI1421464 and DORMAN 917445.

This table covers the drain plugs in the oil pan. Read more

6 Oil Drain Plug parts are listed for the 2018 Nissan Murano, from DORMAN, AGS, BECK/ARNLEY and 2 other brands. DORMAN 090038 carries the "Popular" badge.

Part numbers include DORMAN 090038, DORMAN 090049 and AGS ODP00011, among others listed above.

This table covers the crush washers and gaskets under the oil drain plug. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

5 Oil Drain Plug Gasket parts for the 2018 Nissan Murano come from 4 brands — DORMAN, AJUSA, APEX and 1 other brand. The "Popular" part is DORMAN 097134.

This group includes DORMAN 097134, AJUSA 01140600 and APEX ADP1904 and the remaining parts above.

This table covers the caps on the oil filler neck. Read more

5 Oil Filler Cap parts are listed for the 2018 Nissan Murano, from MOTORAD, CALORSTAT, DORMAN and 2 other brands. MOTORAD MO107 carries the "Popular" badge.

This group includes MOTORAD MO107, CALORSTAT OC2316 and DORMAN 90200 and the remaining parts above.

This table covers the oil filters that screw onto this engine's filter mount. Typical signs include low oil pressure after a service, or a filter that will not spin off because the old gasket stayed on the block. Lube the new gasket and tighten to the spec on the box; a double-gasket install dumps the sump on the first drive. Read more

18 Oil Filter parts are listed for the 2018 Nissan Murano, from VARIOUS MFR, BOSCH, WIX and 11 other brands. MOBIL M1108A carries the "Popular" badge.

Economy: 6 parts, from VARIOUS MFR, BOSCH, FRAM and 2 other brands. A representative part number is BOSCH 72230WS.

In the High Performance / Heavy Duty grade, MOBIL and WIX supply 2 parts: grouped under the catalog's "High Performance / Heavy Duty" designation — the notes column spells out what sets them apart. A representative part number is MOBIL M1108A.

The Standard Replacement section: 10 options from BOSCH, MOTORCRAFT, WIX and 7 other brands. BOSCH 3300 is listed in this group.

This table covers the oil pans that hold the engine's oil sump. Read more

6 Oil Pan parts for the 2018 Nissan Murano come from 6 brands — SKP, ACKOJA, DORMAN and 3 other brands. The "Popular" part is SKP SK264465.

Listed part numbers: SKP SK264465, ACKOJA A380555 and DORMAN 264505, plus the other parts above.

This table covers the gaskets between the oil pan and the block. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

9 Oil Pan Gasket parts are listed for the 2018 Nissan Murano, from VICTOR REINZ, APEX, MAHLE / CLEVITE and 2 other brands. FEL-PRO OS30696 carries the "Popular" badge.

Part numbers include FEL-PRO OS30696, VICTOR REINZ 703141410 and AJUSA 59010400, among others listed above.

This table covers the Oil pumps. Typical signs include noise from the pump, no pressure, or fluid that never arrives at the outlet. Prime or fill the pump as the notes require. A dry start is a common way to kill a new unit. Read more

2 Oil Pump parts are listed for the 2018 Nissan Murano, from ASTEMO / HITACHI and TOPLINE.

Listed part numbers: ASTEMO / HITACHI OUP0037 and TOPLINE OPD41M.

This table covers the pistons that travel in each cylinder. Typical signs include knock, blow-by, or a cylinder that will not hold compression. Piston work is a short-block job. Match bore, pin and ring pack in the notes — not the photo. Read more

This group shows a single part: ENGINETECH K16016P.

This table covers the Piston Pin bushings. Typical signs include a clunk over bumps, or a torn or walked-out bushing you can see. Press the new bushing square. A cocked bushing will tear in a few thousand miles. Read more

2 Piston Pin Bushing parts are listed for the 2018 Nissan Murano, from ENGINETECH and TOPLINE.

This group includes ENGINETECH EB0156 and TOPLINE PBD34.

This table covers the Thrust washers. Read more

One part is listed for the 2018 Nissan Murano — KING ENGINE BEARINGS TW271AM.

This table covers the timing chains that keep the cams in time with the crank. Read more

7 Timing Chain parts for the 2018 Nissan Murano come from 4 brands — MELLING, S.A. GEAR, CLOYES and 1 other brand. The "Popular" part is MELLING 721.

Part numbers include MELLING 721, S.A. GEAR RC1038 and CLOYES C721F, among others listed above.

This table covers kits that group a timing chain with the related tensioners and guides. Read more

5 Timing Chain & Component Kit parts are listed for the 2018 Nissan Murano, from S.A. GEAR, CLOYES, INA and 1 other brand. CLOYES 90730SB carries the "Popular" badge.

Economy: 2 parts, from S.A. GEAR. A representative part number is S.A. GEAR 76280S.

The Standard Replacement section: 3 options from CLOYES, INA and MELLING. CLOYES 90730SB is listed in this group.

This group includes CLOYES 90730SB, S.A. GEAR 76280S and S.A. GEAR 76280SW and the remaining parts above.

This table covers the guides and dampers that keep the timing chain on its path. Read more

11 Timing Chain Guide / Damper parts for the 2018 Nissan Murano come from 5 brands — S.A. GEAR, CLOYES, INA and 2 other brands. The "Popular" part is S.A. GEAR 71009.

This table covers the tensioners that keep the timing chain taut. Typical signs include belt flutter, a chirp that returns after a new belt, or an arm that no longer damps. Replace the tensioner with the belt at higher mileage. Read more

14 Timing Chain Tensioner parts are listed for the 2018 Nissan Murano, from S.A. GEAR, CLOYES, INA and 2 other brands. S.A. GEAR 9441 carries the "Popular" badge.

This table covers the gaskets that seal the Timing Cover. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

5 Timing Cover Gasket parts are listed for the 2018 Nissan Murano, from MAHLE / CLEVITE, APEX and ULTRA-POWER.

This group includes APEX ATC5340, MAHLE / CLEVITE B33343 and MAHLE / CLEVITE B33342 and the remaining parts above.

This table covers the wear sleeves used to restore a Timing Cover seal surface. Read more

One part is listed for the 2018 Nissan Murano — SKF 99189.

This table covers the seals at the Timing Cover. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

2 Timing Cover Seal parts are listed for the 2018 Nissan Murano, from MAHLE / CLEVITE and SKF.

This group includes MAHLE / CLEVITE 67689 and SKF 18857.

This table covers the crankshaft sprockets that drive the timing chain or belt. Read more

4 Timing Crank Sprocket parts are listed for the 2018 Nissan Murano, from CLOYES, FVP, INA and 1 other brand.

Listed part numbers: CLOYES S947 and INA ZSS1221, plus the other parts above.

This table covers the Torque Strut mounts. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes. Read more

6 Torque Strut Mount parts for the 2018 Nissan Murano come from 4 brands — ANCHOR, DEA / MARMON RIDE CONTROL, SKP and 1 other brand. The "Popular" part is SKP SKM9747.

The Economy section: 1 option from SKP. SKP SKM9747 is listed in this group.

Standard Replacement: 5 parts, from ANCHOR, DEA / MARMON RIDE CONTROL and PIONEER. A representative part number is ANCHOR 9747.

Listed part numbers: SKP SKM9747, ANCHOR 9747 and ANCHOR 9551, plus the other parts above.

This table covers the Valve covers. Read more

7 Valve Cover parts for the 2018 Nissan Murano come from 4 brands — APEX, DORMAN, ITM ENGINE COMPONENTS and 1 other brand. The "Popular" part is APEX VCS528R.

This group includes APEX VCS528R, DORMAN 264787 and ACKOJA A380699 and the remaining parts above.

This table covers the gaskets that seal the valve cover to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

11 Valve Cover Gasket parts are listed for the 2018 Nissan Murano, from BECK/ARNLEY, APEX, AJUSA and 3 other brands. APEX AVC562 carries the "Popular" badge.

This table covers the pressed-in bronze and cast-iron guides that align valve stems. Typical signs include oil smoke on startup, a guide that has gone oval, or a valve that no longer seats quietly. Guides are a machine-shop fit. Confirm stem diameter in the notes before ordering. Read more

5 Valve Guide parts are listed for the 2018 Nissan Murano, from SBI, QUALCAST and TOPLINE. SBI 1408217 carries the "Popular" badge.

Part numbers include SBI 1408217, QUALCAST 308217 and QUALCAST 308190, among others listed above.