2013 Toyota Highlander Automatic Transmission Parts

This table covers the Boost valves. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

This group shows a single part: TRANSGO U151BOOST.

This table covers the Bushing kits. Read more

One part is listed for the 2013 Toyota Highlander — DURA-BOND TK26.

This table covers the vents on a transmission or axle housing. Read more

This group shows a single part: DORMAN 926811.

This table covers the clutch-plate packs inside the transmission or transfer case. Read more

RAYBESTOS POWERTRAIN supplies the 5 Clutch Plate Pack parts for the 2013 Toyota Highlander.

The Friction Plate Pack section lists 3 options from RAYBESTOS POWERTRAIN — grouped under the catalog's "Friction Plate Pack" designation — the notes column spells out what sets them apart. RAYBESTOS POWERTRAIN RHT96286 is listed in this group.

In the Steel Plate Pack grade, RAYBESTOS POWERTRAIN supplies 2 parts: grouped under the catalog's "Steel Plate Pack" designation — the notes column spells out what sets them apart. A representative part number is RAYBESTOS POWERTRAIN STMTOYTA58.

This group includes RAYBESTOS POWERTRAIN RHT96286, RAYBESTOS POWERTRAIN FRMTOYTA58 and RAYBESTOS POWERTRAIN FRMTOYTA42 and the remaining parts above.

This table covers the related components grouped with this assembly. Read more

One part is listed for the 2013 Toyota Highlander — SONNAX 57917E03K.

This table covers the gaskets that seal the Drain Plug. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

This group shows a single part: DORMAN 652531CD.

This table covers the End plugs. Typical signs include a leak at the drain or glow-plug hole, or a plug that has rounded off. Replace the crush washer and torque to the spec in the notes. Read more

This group shows a single part: PA CARGO K096.

This table covers the seals at the Extension Housing. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

3 Extension Housing Seal parts for the 2013 Toyota Highlander come from 3 brands — BCA, NATIONAL and WJB / INMOTION PARTS.

Listed part numbers: BCA NS710319, NATIONAL 710319 and WJB / INMOTION PARTS WS710319.

This table covers the replacement filters for this application — the table heading and notes say which circuit. Typical signs include restricted flow — long cranking, weak airflow, or dirty fluid after a short interval. Seat the new filter so it cannot bypass, and use the grade the notes call for. Read more

18 Filter parts are listed for the 2013 Toyota Highlander, from VAICO, ATP, AUTOTECNICA and 6 other brands. ATP B224 carries the "Popular" badge.

In the Economy grade, AUTOTECNICA, VARIOUS MFR, ATP and 1 other brand supply 6 parts: the catalog's value-priced group. A representative part number is ATP TF224.

The Standard Replacement section lists 12 options from VAICO, ATP, BECK/ARNLEY and 3 other brands — built to original-equipment specification. ATP B224 is listed in this group.

This table covers the heat exchangers that cool transmission fluid. Typical signs include fluid that overheats, a leak at the cooler fittings, or milky fluid that says coolant and ATF have mixed. Flush the lines when you replace a cooler. Cross-contamination is how a small leak becomes a transmission job. Read more

4 Fluid Cooler parts are listed for the 2013 Toyota Highlander, from DORMAN, TECHPRO, TYC and 1 other brand. 2 parts fit every engine; the other 2 are engine-specific.

This group includes DORMAN 918551, TECHPRO TO4050116 and TYC 19121 and the remaining parts above.

This table covers the Fluid Cooler O-rings. Typical signs include a seep at a fitting or a housing that weeps after a service. Lube the new O-ring with the fluid it will see, and do not roll it into the groove. Read more

One part is listed for the 2013 Toyota Highlander — AJUSA 13181750.

This table covers the pans that hold automatic-transmission fluid. Read more

7 Fluid Pan parts for the 2013 Toyota Highlander come from 4 brands — SKP, REIN, SPECTRA PREMIUM and 1 other brand. The "Popular" part is SKP SK265836.

Listed part numbers: SKP SK265836, SKP SK265868 and ATP 103372, plus the other parts above.

This table covers the gaskets that seal the Fluid Pan. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

7 Fluid Pan Gasket parts are listed for the 2013 Toyota Highlander, from MAHLE / CLEVITE, FEL-PRO, ATP and 3 other brands. FEL-PRO TOS18719 carries the "Popular" badge. 1 part fits every engine; the other 6 are engine-specific.

Listed part numbers: FEL-PRO TOS18719, MAHLE / CLEVITE W33428 and ATP RG88, plus the other parts above.

This table covers the Fluid Pump bushings. Typical signs include a clunk over bumps, or a torn or walked-out bushing you can see. Press the new bushing square. A cocked bushing will tear in a few thousand miles. Read more

One part is listed for the 2013 Toyota Highlander — DURA-BOND TOT24TG.

This table covers the seals at the Fluid Pump. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

3 Fluid Pump Seal parts for the 2013 Toyota Highlander come from 3 brands — SCHAEFFLER, SKF and TIMKEN. 1 part fits every engine; the other 2 are engine-specific.

Listed part numbers: SCHAEFFLER SS6193, SKF 15302 and TIMKEN 710112.

This table covers the seals at the Manual Shaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

4 Manual Shaft Seal parts for the 2013 Toyota Highlander come from 4 brands — BCA, NATIONAL, TIMKEN and 1 other brand.

This group includes BCA NS221207 and NATIONAL 221207 and the remaining parts above.

This table covers the wear sleeves used to restore a Output Shaft seal surface. Read more

11 Output Shaft Repair Sleeve parts are listed for the 2013 Toyota Highlander, from NATIONAL, WJB / INMOTION PARTS and BCA. NATIONAL 99157 carries the "Popular" badge. 2 parts fit every engine; the other 9 are engine-specific.

This table covers the seals at the Output Shaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

27 Output Shaft Seal parts are listed for the 2013 Toyota Highlander, from NATIONAL, WJB / INMOTION PARTS, BCA and 4 other brands. NATIONAL 712551 carries the "Popular" badge. The notes list position, dimensions and spec qualifiers wherever the manufacturer distinguishes between variants.

This table covers the Pressure Control (EPC) solenoids. Typical signs include a harsh or missing shift, or a code for this solenoid circuit. Check resistance and the connector before dropping the pan for a solenoid. Read more

7 Pressure Control (EPC) Solenoid parts are listed for the 2013 Toyota Highlander, from ROSTRA, STANDARD MOTOR PRODUCTS, ATP and 2 other brands. ROSTRA 520414 carries the "Popular" badge.

This group includes ROSTRA 520414, STANDARD MOTOR PRODUCTS TCS307 and ATP RE37 and the remaining parts above.

This table covers the rebuild kits for this assembly. Read more

4 Rebuild Kit parts for the 2013 Toyota Highlander come from 2 brands — PA CARGO and TRANSTEC. 3 parts fit every engine; the other 1 is engine-specific.

The Banner Kit (Overhaul Kit + Friction Clutch Plates) section lists 1 option from PA CARGO — grouped under the catalog's "Banner Kit (Overhaul Kit + Friction Clutch Plates)" designation — the notes column spells out what sets them apart. PA CARGO DK5700NS is listed in this group.

In the Master Kit (Overhaul Kit + Friction & Steel Clutch Plates) grade, PA CARGO supplies 1 part: grouped under the catalog's "Master Kit (Overhaul Kit + Friction & Steel Clutch Plates)" designation — the notes column spells out what sets them apart. A representative part number is PA CARGO DK5700N.

The Overhaul Kit (Gaskets, Seals, O-Rings & Sealing Rings) section lists 1 option from TRANSTEC — grouped under the catalog's "Overhaul Kit (Gaskets, Seals, O-Rings & Sealing Rings)" designation — the notes column spells out what sets them apart. TRANSTEC 81000633 is listed in this group.

1 further part sits outside the graded sections, with the same engine-level match.

Part numbers include PA CARGO DK5700NS, PA CARGO DK5700N and TRANSTEC 81000633, among others listed above.

This table covers the pistons in a transmission servo. Read more

One part is listed for the 2013 Toyota Highlander — PA CARGO K57900N99.

This table covers the Shift cables. Typical signs include a stretched or frayed cable, or a control that no longer reaches the end of its travel. Route the new cable through the same clips. A kinked cable binds and fails early. Read more

2 Shift Cable parts for the 2013 Toyota Highlander come from 2 brands — ATP and PIONEER.

Listed part numbers: ATP Y1803 and PIONEER CA1489.

This table covers the Shift Improvement kits. Read more

4 Shift Improvement Kit parts are listed for the 2013 Toyota Highlander, from SONNAX and TRANSGO.

Part numbers include SONNAX U151EU250EZIP, SONNAX U760EZIP and TRANSGO SKU760E, among others listed above.

This table covers the Shift Linkage bushings. Typical signs include a clunk over bumps, or a torn or walked-out bushing you can see. Press the new bushing square. A cocked bushing will tear in a few thousand miles. Read more

This group shows a single part: DORMAN 14103.

This table covers the seals at the Shift Shaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

This group shows a single part: SCHAEFFLER SS2111.

This table covers the Shift solenoids. Typical signs include a harsh or missing shift, or a code for this solenoid circuit. Check resistance and the connector before dropping the pan for a solenoid. Read more

17 Shift Solenoid parts for the 2013 Toyota Highlander come from 7 brands — ACKOJA, ROSTRA, STANDARD MOTOR PRODUCTS and 4 other brands. The "Popular" part is ROSTRA 520381. 4 parts fit every engine; the other 13 are engine-specific.

This table covers the seals at the Side Cover. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

2 Side Cover Seal parts for the 2013 Toyota Highlander come from 2 brands — NATIONAL and WJB / INMOTION PARTS. Every part fits all 3 engine options (2.7L L4, 3.5L V6 and 3.5L V6 ELECTRIC/GAS).

Part numbers include NATIONAL 711095 and WJB / INMOTION PARTS WS711095.

This table covers the Sun Gear bushings. Typical signs include a clunk over bumps, or a torn or walked-out bushing you can see. Press the new bushing square. A cocked bushing will tear in a few thousand miles. Read more

This group shows a single part: DURA-BOND TOT22.

This table covers the Torque converters. Typical signs include a sulfur smell, rattling substrate, or an efficiency code. Confirm CARB vs Federal certification in the notes before ordering. Read more

TC REMANUFACTURING supplies the 3 Torque Converter parts for the 2013 Toyota Highlander.

This group includes TC REMANUFACTURING TO429, TC REMANUFACTURING TO42LS and TC REMANUFACTURING TO98.

This table covers the Torque Converter Clutch solenoids. Typical signs include a harsh or missing shift, or a code for this solenoid circuit. Check resistance and the connector before dropping the pan for a solenoid. Read more

2 Torque Converter Clutch Solenoid parts are listed for the 2013 Toyota Highlander, from ROSTRA and STANDARD MOTOR PRODUCTS.

Part numbers include ROSTRA 520380 and STANDARD MOTOR PRODUCTS TCS140.

This table covers the wear sleeves used to restore a Torque Converter seal surface. Read more

3 Torque Converter Repair Sleeve parts for the 2013 Toyota Highlander come from 3 brands — BCA, NATIONAL and WJB / INMOTION PARTS. 1 part fits every engine; the other 2 are engine-specific.

Part numbers include BCA NS99147, NATIONAL 99147 and WJB / INMOTION PARTS WS99147.

This table covers the seals at the Torque Converter Shaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

6 Torque Converter Shaft Seal parts for the 2013 Toyota Highlander come from 3 brands — NATIONAL, WJB / INMOTION PARTS and SCHAEFFLER. The "Popular" part is NATIONAL 223830.

This group includes NATIONAL 223830, WJB / INMOTION PARTS WS223830 and NATIONAL 710929 and the remaining parts above.

This table covers the automatic-transmission fluids specified for this gearbox. Typical signs include harsh or delayed shifts, fluid that smells burnt, or a shudder at light throttle. Use exactly the specification in the notes. Automatic transmissions are unforgiving of the wrong fluid. Read more

20 Transmission Fluid parts are listed for the 2013 Toyota Highlander, from VALVOLINE, LIQUI MOLY, PENTOSIN and 7 other brands. ACDELCO 109243 carries the "Popular" badge. 17 parts fit every engine; the other 3 are engine-specific.

The ATF 64 section lists 2 options from PENTOSIN — grouped under the catalog's "ATF 64" designation — the notes column spells out what sets them apart. PENTOSIN 1058113 is listed in this group.

The CVT section lists 1 option from LUBEGARD — grouped under the catalog's "CVT" designation — the notes column spells out what sets them apart. LUBEGARD 68112 is listed in this group.

In the Dexron grade, ACDELCO supplies 1 part: grouped under the catalog's "Dexron" designation — the notes column spells out what sets them apart. A representative part number is ACDELCO 109243.

In the Multi-Vehicle grade, VALVOLINE, LIQUI MOLY, LUCAS OIL and 2 other brands supply 11 parts: grouped under the catalog's "Multi-Vehicle" designation — the notes column spells out what sets them apart. A representative part number is MOBIL 126505.

In the World Standard (WS) grade, IDEMITSU and AISIN supply 3 parts: grouped under the catalog's "World Standard (WS)" designation — the notes column spells out what sets them apart. A representative part number is AISIN ATF0WS.

In the ZF Fluid grade, ZF supplies 1 part: grouped under the catalog's "ZF Fluid" designation — the notes column spells out what sets them apart. A representative part number is ZF 5961308623.

1 ungrouped part is not assigned to a grade, with the same engine-level match.

This table covers the conditioners and additives used with this transmission fluid. Read more

LUBEGARD supplies the 9 Transmission Fluid Additive parts for the 2013 Toyota Highlander. LUBEGARD 19610 carries the "Popular" badge.

Part numbers include LUBEGARD 19610, LUBEGARD 60902 and LUBEGARD 19689, among others listed above.

This table covers the mounts that hold the transmission to the chassis. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes. Read more

14 Transmission Mount parts for the 2013 Toyota Highlander come from 6 brands — WESTAR, ANCHOR, DEA / MARMON RIDE CONTROL and 3 other brands. The "Popular" part is SKP SKM9236.

The Economy section: 1 option from SKP. SKP SKM9236 is listed in this group.

Standard Replacement: 5 parts, from WESTAR, ANCHOR, BECK/ARNLEY and 2 other brands. A representative part number is WESTAR EM9236.

8 further parts sit outside the graded sections, with the same engine-level match.

This table covers the valve bodies that route hydraulic pressure inside the transmission. Read more

One part is listed for the 2013 Toyota Highlander — SONNAX TOY181.

This table covers the testers used to diagnose a valve body. Read more

One part is listed for the 2013 Toyota Highlander — SONNAX 47740VTP.