2013 Toyota Highlander Drivetrain Parts

This table covers the seals where an axle shaft exits the housing. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

5 Axle Shaft Seal parts are listed for the 2013 Toyota Highlander, from TIMKEN, SKF and SCHAEFFLER. SKF 13725 carries the "Popular" badge. All of them fit every engine offered in the 2013 Highlander.

Part numbers include SKF 13725, SCHAEFFLER SS2416 and TIMKEN 710419, among others listed above.

This table covers the complete CV axle shafts from differential (or hub) to wheel. Typical signs include a click in tight turns, grease flung around the wheel well, or a vibration that builds with speed. A torn boot caught early is a boot kit; caught late it is the whole axle. Torque the axle nut to the method in the notes. Read more

36 CV Axle parts are listed for the 2013 Toyota Highlander, from TRAKMOTIVE, GSP, TOP NOTCH and 2 other brands. APWI TO8441A carries the "Popular" badge. Grades run from Economy through Standard Replacement; Standard Replacement is the most populated section, led by TRAKMOTIVE, GSP, TOP NOTCH and 2 other brands.

This table covers the brackets that mount the CV Axle Support Bearing. Typical signs include a cracked mount, a rattle, or a bracket that no longer holds alignment. Confirm position in the notes. Many brackets look alike and bolt to different corners. Read more

4 CV Axle Support Bearing Bracket parts for the 2013 Toyota Highlander come from 4 brands — DORMAN, GSP, TOP NOTCH and 1 other brand.

Listed part numbers: DORMAN 926195, GSP NB1005 and TOP NOTCH TN18279CB, plus the other parts above.

This table covers the boots that keep grease in a CV joint. Typical signs include a split boot, grease flung around the joint, or a click once grit is inside. A boot caught early is a kit. Once the joint has clicked, the joint itself is usually worn. Read more

14 CV Joint Boot parts are listed for the 2013 Toyota Highlander, from BECK/ARNLEY, MEVOTECH and ACKOJA. BECK/ARNLEY 1032942 carries the "Popular" badge.

This table covers the bearings and races that support the differential carrier. Read more

12 Differential Carrier Bearing / Race parts are listed for the 2013 Toyota Highlander, from SKF, SCHAEFFLER, WJB / INMOTION PARTS and 3 other brands. WJB / INMOTION PARTS WTLM501310 carries the "Popular" badge. 5 parts fit every engine; the other 7 are engine-specific.

In the Economy grade, WJB / INMOTION PARTS supplies 2 parts: the catalog's value-priced group. A representative part number is WJB / INMOTION PARTS WTLM501310.

The Standard Replacement section lists 10 options from SKF, SCHAEFFLER, BCA and 2 other brands — built to original-equipment specification. SKF LM501310VP is listed in this group.

This table covers the bearings and races on the differential pinion. Read more

6 Differential Pinion Bearing / Race parts for the 2013 Toyota Highlander come from 3 brands — SKF, SCHAEFFLER and MEVOTECH. The "Popular" part is SKF M86610VP. Every part fits all 3 engine options (2.7L L4, 3.5L V6 and 3.5L V6 ELECTRIC/GAS).

Part numbers include SKF M86610VP, SKF HM88610 and MEVOTECH MB50385, among others listed above.

This table covers the wear sleeves used to restore a grooved pinion seal surface. Read more

One part is listed for the 2013 Toyota Highlander — SKF 99147.

This table covers the seals at the differential pinion yoke. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

2 Differential Pinion Seal parts are listed for the 2013 Toyota Highlander, from SKF and TIMKEN. All of them fit every engine offered in the 2013 Highlander.

Listed part numbers: SKF 14758 and TIMKEN 710594.

This table covers the seals at the Differential. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

3 Differential Seal parts for the 2013 Toyota Highlander come from 3 brands — NATIONAL, TIMKEN and WJB / INMOTION PARTS. Every part fits all 3 engine options (2.7L L4, 3.5L V6 and 3.5L V6 ELECTRIC/GAS).

Part numbers include NATIONAL 710419 and WJB / INMOTION PARTS WS710419, among others listed above.

This table covers the driveshafts that carry torque from the transmission or transfer case. Read more

7 Drive Shaft parts for the 2013 Toyota Highlander come from 6 brands — WJB / INMOTION PARTS, TOP NOTCH, CARDONE and 3 other brands. The "Popular" part is TOP NOTCH TN6919PS. 4 parts fit every engine; the other 3 are engine-specific.

Part numbers include TOP NOTCH TN6919PS, WJB / INMOTION PARTS WDS655006 and CARDONE 655006, among others listed above.

This table covers the Drive Shaft Center Support bearings. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

18 Drive Shaft Center Support Bearing parts for the 2013 Toyota Highlander come from 10 brands — WESTAR, DEA / MARMON RIDE CONTROL, WJB / INMOTION PARTS and 7 other brands. The "Popular" part is WESTAR DS5229. 15 parts fit every engine; the other 3 are engine-specific.

The Economy section: 6 options from WESTAR, DEA / MARMON RIDE CONTROL and WJB / INMOTION PARTS. WESTAR DS5229 is listed in this group.

Standard Replacement: 12 parts, from ANCHOR, SKF, BCA and 4 other brands. A representative part number is ANCHOR 6083.

This table covers the gear oils specified for the axle or transfer case. Typical signs include a low-oil lamp, knocking, or oil that has gone thin before the next interval. Match the viscosity and spec in the notes, not just the weight on the bottle. Read more

27 Gear Oil parts are listed for the 2013 Toyota Highlander, from VALVOLINE, LUCAS OIL, MOBIL and 3 other brands. ACDELCO 109243 carries the "Popular" badge. They are grouped as ATF 64, Dexron, Multi-Vehicle, SAE 75W-90, SAE 80W-90 and World Standard (WS), with SAE 75W-90 the largest group at 7 parts from VALVOLINE and MOBIL.

This table covers the fluids specified for the transfer case. Typical signs include discolored fluid, a burnt smell, or a level that keeps dropping. Use only the specification in the notes — the tables group grades because they are not interchangeable. Read more

15 Transfer Case Fluid parts are listed for the 2013 Toyota Highlander, from VALVOLINE, LUCAS OIL, MOBIL and 1 other brand. MOBIL 104361 carries the "Popular" badge.

In the SAE 75W-90 grade, VALVOLINE and MOBIL supply 7 parts: grouped under the catalog's "SAE 75W-90" designation — the notes column spells out what sets them apart. A representative part number is MOBIL 104361.

In the SAE 80W-90 grade, VALVOLINE and LUCAS OIL supply 7 parts: grouped under the catalog's "SAE 80W-90" designation — the notes column spells out what sets them apart. A representative part number is LUCAS OIL 10043.

1 ungrouped part is not assigned to a grade, with the same engine-level match.

This table covers the seals at the Transfer Case Housing Extension. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

4 Transfer Case Housing Extension Seal parts for the 2013 Toyota Highlander come from 4 brands — BCA, NATIONAL, SCHAEFFLER and 1 other brand. Every part fits all 3 engine options (2.7L L4, 3.5L V6 and 3.5L V6 ELECTRIC/GAS).

This group includes BCA NS710319, NATIONAL 710319 and SCHAEFFLER SS3716 and the remaining parts above.

This table covers the Transfer Case Input Shaft bearings. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

2 Transfer Case Input Shaft Bearing parts are listed for the 2013 Toyota Highlander, from SCHAEFFLER and SKF. All of them fit every engine offered in the 2013 Highlander.

This group includes SCHAEFFLER BT2050 and SKF BR112.

This table covers the wear sleeves used to restore a Transfer Case Input Shaft seal surface. Read more

This group shows a single part: SKF 99219.

This table covers the seals at the Transfer Case Input Shaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

3 Transfer Case Input Shaft Seal parts for the 2013 Toyota Highlander come from 3 brands — NATIONAL, SKF and WJB / INMOTION PARTS. Every part fits all 3 engine options (2.7L L4, 3.5L V6 and 3.5L V6 ELECTRIC/GAS).

Listed part numbers: NATIONAL 710910, SKF 23234 and WJB / INMOTION PARTS WS710910.

This table covers the Transfer Case Output Shaft bearings. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

2 Transfer Case Output Shaft Bearing parts for the 2013 Toyota Highlander come from 2 brands — SCHAEFFLER and SKF. Every part fits all 3 engine options (2.7L L4, 3.5L V6 and 3.5L V6 ELECTRIC/GAS).

Listed part numbers: SCHAEFFLER KT708 and SKF BR119.

This table covers the wear sleeves used to restore a Transfer Case Output Shaft seal surface. Read more

3 Transfer Case Output Shaft Repair Sleeve parts are listed for the 2013 Toyota Highlander, from BCA, NATIONAL and WJB / INMOTION PARTS. All of them fit every engine offered in the 2013 Highlander.

Part numbers include BCA NS99145, NATIONAL 99145 and WJB / INMOTION PARTS WS99145.

This table covers the seals at the Transfer Case Output Shaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

5 Transfer Case Output Shaft Seal parts are listed for the 2013 Toyota Highlander, from SKF, WJB / INMOTION PARTS and NATIONAL. SKF 14958 carries the "Popular" badge. All of them fit every engine offered in the 2013 Highlander.

Part numbers include SKF 14958, NATIONAL 710807 and SKF 14632A, among others listed above.

This table covers the U-joints in the driveshaft. Read more

One part is listed for the 2013 Toyota Highlander — GKN U024.