2016 Toyota Sequoia Drivetrain Parts

This table covers the actuators that engage four-wheel drive at the transfer case or axle. Typical signs include a door or range that will not move, or a click with no motion. Confirm the command signal before replacing the actuator — a failed module looks the same. Read more

3 4WD Actuator parts for the 2016 Toyota Sequoia come from 3 brands — AISIN, STANDARD MOTOR PRODUCTS and WELLS.

This group includes AISIN SAT011, STANDARD MOTOR PRODUCTS TCA104 and WELLS 1S15514.

This table covers the seals at the Axle Intermediate Shaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

This group shows a single part: TIMKEN 710595.

This table covers the Axle shafts. Read more

This group shows a single part: USA STANDARD GEAR USA21661.

This table covers the seals where an axle shaft exits the housing. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

11 Axle Shaft Seal parts are listed for the 2016 Toyota Sequoia, from NATIONAL, SKF, BCA and 3 other brands. NATIONAL 710596 carries the "Popular" badge.

This table covers the complete CV axle shafts from differential (or hub) to wheel. Typical signs include a click in tight turns, grease flung around the wheel well, or a vibration that builds with speed. A torn boot caught early is a boot kit; caught late it is the whole axle. Torque the axle nut to the method in the notes. Read more

17 CV Axle parts are listed for the 2016 Toyota Sequoia, from TRAKMOTIVE, GSP, CARDONE and 2 other brands. TRAKMOTIVE TO8250HDX carries the "Popular" badge.

In the Economy grade, CARDONE supplies 1 part: the catalog's value-priced group. A representative part number is CARDONE 605252.

The Heavy Duty section lists 2 options from TRAKMOTIVE and GSP — rated for severe service. TRAKMOTIVE TO8250HDX is listed in this group.

The Specialty - For Lifted Vehicles section lists 3 options from GSP, TOP NOTCH and TRAKMOTIVE — grouped under the catalog's "Specialty - For Lifted Vehicles" designation — the notes column spells out what sets them apart. GSP NCV69164XDP is listed in this group.

The Standard Replacement section lists 11 options from TRAKMOTIVE, GSP, APWI and 2 other brands — built to original-equipment specification. APWI TO8363 is listed in this group.

This table covers the CV Intermediate shafts. Read more

This group shows a single part: TRAKMOTIVE TO3512.

This table covers the boots that keep grease in a CV joint. Typical signs include a split boot, grease flung around the joint, or a click once grit is inside. A boot caught early is a kit. Once the joint has clicked, the joint itself is usually worn. Read more

3 CV Joint Boot parts are listed for the 2016 Toyota Sequoia, from BECK/ARNLEY and MEVOTECH.

Listed part numbers: BECK/ARNLEY 1033133, BECK/ARNLEY 1032872 and MEVOTECH DX530.

This table covers the Differential Carrier shims. Read more

3 Differential Carrier Shim parts for the 2016 Toyota Sequoia come from MOTIVE GEAR.

Listed part numbers: MOTIVE GEAR GM95MSK, MOTIVE GEAR GM95SSK and MOTIVE GEAR SK47.

This table covers the Differential Crush sleeves. Read more

This group shows a single part: MOTIVE GEAR 4123134040.

This table covers the Differential Lock actuators. Typical signs include a door or range that will not move, or a click with no motion. Confirm the command signal before replacing the actuator — a failed module looks the same. Read more

One part is listed for the 2016 Toyota Sequoia — DORMAN 600420.

This table covers the Differential mounts. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes. Read more

This group shows a single part: BECK/ARNLEY 1042457.

This table covers the bearings and races on the differential pinion. Read more

2 Differential Pinion Bearing / Race parts for the 2016 Toyota Sequoia come from SKF.

This group includes SKF BR4090 and SKF BR911.

This table covers the Differential Pinion nuts. Read more

One part is listed for the 2016 Toyota Sequoia — MOTIVE GEAR 90179A0002.

This table covers the wear sleeves used to restore a grooved pinion seal surface. Read more

WJB / INMOTION PARTS supplies both parts for the 2016 Toyota Sequoia.

This group includes WJB / INMOTION PARTS WS99204 and WJB / INMOTION PARTS WS99181.

This table covers the seals at the differential pinion yoke. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

8 Differential Pinion Seal parts are listed for the 2016 Toyota Sequoia, from NATIONAL, SKF, WJB / INMOTION PARTS and 1 other brand. NATIONAL 710734 carries the "Popular" badge.

Listed part numbers: NATIONAL 710734, NATIONAL 710931 and NATIONAL 711186, plus the other parts above.

This table covers kits that group the bearings, races and seals for a differential rebuild. Read more

5 Differential Rebuild Kit parts for the 2016 Toyota Sequoia come from 4 brands — BCA, MOTIVE GEAR, RICHMOND and 1 other brand. The "Popular" part is BCA NBDRK381MK.

The Master Kit section lists 3 options from BCA, MOTIVE GEAR and RICHMOND — grouped under the catalog's "Master Kit" designation — the notes column spells out what sets them apart. BCA NBDRK381MK is listed in this group.

In the Standard Kit grade, BCA and LUK supply 2 parts: grouped under the catalog's "Standard Kit" designation — the notes column spells out what sets them apart. A representative part number is BCA NBDRK381.

Part numbers include BCA NBDRK381MK, MOTIVE GEAR RT9RMK and RICHMOND XL20211, among others listed above.

This table covers the ring-and-pinion gear sets that set the axle ratio. Read more

One part is listed for the 2016 Toyota Sequoia — MOTIVE GEAR T9.

This table covers the Differential Ring Gear bolts. Read more

One part is listed for the 2016 Toyota Sequoia — MOTIVE GEAR 9010512365.

This table covers the driveshafts that carry torque from the transmission or transfer case. Read more

7 Drive Shaft parts for the 2016 Toyota Sequoia come from 4 brands — DORMAN, WJB / INMOTION PARTS, GSP and 1 other brand. The "Popular" part is DORMAN 986149.

Listed part numbers: DORMAN 986149, DORMAN 938339 and DORMAN 936744, plus the other parts above.

This table covers the gear oils specified for the axle or transfer case. Typical signs include a low-oil lamp, knocking, or oil that has gone thin before the next interval. Match the viscosity and spec in the notes, not just the weight on the bottle. Read more

3 Gear Oil parts are listed for the 2016 Toyota Sequoia, from VALVOLINE and IDEMITSU.

Listed part numbers: IDEMITSU 30305024750, VALVOLINE 915052 and VALVOLINE 915053.

This table covers the Gear Oil additives. Read more

One part is listed for the 2016 Toyota Sequoia — USA STANDARD GEAR USA15018.

This table covers the fluids specified for the transfer case. Typical signs include discolored fluid, a burnt smell, or a level that keeps dropping. Use only the specification in the notes — the tables group grades because they are not interchangeable. Read more

13 Transfer Case Fluid parts are listed for the 2016 Toyota Sequoia, from VALVOLINE, LUCAS OIL, MOBIL and 2 other brands. MOBIL 104361 carries the "Popular" badge.

This table covers the seals at the Transfer Case Housing Extension. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

2 Transfer Case Housing Extension Seal parts for the 2016 Toyota Sequoia come from 2 brands — NATIONAL and WJB / INMOTION PARTS.

Listed part numbers: NATIONAL 710932 and WJB / INMOTION PARTS WS710932.

This table covers the wear sleeves used to restore a Transfer Case Input Shaft seal surface. Read more

3 Transfer Case Input Shaft Repair Sleeve parts for the 2016 Toyota Sequoia come from 3 brands — BCA, NATIONAL and WJB / INMOTION PARTS.

Part numbers include BCA NS99196, NATIONAL 99196 and WJB / INMOTION PARTS WS99196.

This table covers the seals at the Transfer Case Input Shaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

This group shows a single part: WJB / INMOTION PARTS WS710956.

This table covers the Transfer Case motors. Typical signs include no motion, a squeal, or a motor that only runs on one speed. Confirm power, ground and the control module before replacing the motor. Read more

2 Transfer Case Motor parts for the 2016 Toyota Sequoia come from 2 brands — AISIN and DORMAN.

Listed part numbers: AISIN SAT005 and DORMAN 600471.

This table covers the Transfer Case Mounting Adapter bearings. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

3 Transfer Case Mounting Adapter Bearing parts are listed for the 2016 Toyota Sequoia, from WJB / INMOTION PARTS, BCA and NATIONAL.

Economy: 1 part, from WJB / INMOTION PARTS. A representative part number is WJB / INMOTION PARTS RB6009.

The Standard Replacement section: 2 options from BCA and NATIONAL. BCA NB109 is listed in this group.

Part numbers include WJB / INMOTION PARTS RB6009, BCA NB109 and NATIONAL 109.

This table covers the seals at the Transfer Case Mounting Adapter. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

3 Transfer Case Mounting Adapter Seal parts for the 2016 Toyota Sequoia come from 3 brands — BCA, NATIONAL and WJB / INMOTION PARTS.

Part numbers include BCA NS710265, NATIONAL 710265 and WJB / INMOTION PARTS WS710265.

This table covers the Transfer Case Output Shaft bearings. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

7 Transfer Case Output Shaft Bearing parts for the 2016 Toyota Sequoia come from 5 brands — BCA, SKF, WJB / INMOTION PARTS and 2 other brands. The "Popular" part is WJB / INMOTION PARTS RB6208.

The Economy section: 1 option from WJB / INMOTION PARTS. WJB / INMOTION PARTS RB6208 is listed in this group.

Standard Replacement: 6 parts, from BCA, SKF, NATIONAL and 1 other brand. A representative part number is NATIONAL 208.

This group includes WJB / INMOTION PARTS RB6208, NATIONAL 208 and BCA NB208S and the remaining parts above.

This table covers the seals at the Transfer Case Output Shaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

8 Transfer Case Output Shaft Seal parts are listed for the 2016 Toyota Sequoia, from WJB / INMOTION PARTS, NATIONAL, SKF and 1 other brand. NATIONAL 710957 carries the "Popular" badge.

Part numbers include NATIONAL 710957, NATIONAL 710956 and SCHAEFFLER SS6637, among others listed above.

This table covers the U-joints in the driveshaft. Read more

49 Universal Joint parts are listed for the 2016 Toyota Sequoia, from DANA, MOOG, SKF and 5 other brands. MOOG 270 carries the "Popular" badge. Economy, Heavy Duty and Standard Replacement are all represented, and Standard Replacement alone accounts for 21 parts.

This table covers the Universal Joint Strap kits. Read more

WJB / INMOTION PARTS supplies the 4 Universal Joint Strap Kit parts for the 2016 Toyota Sequoia.

Part numbers include WJB / INMOTION PARTS UJT33110, WJB / INMOTION PARTS UJT43710 and WJB / INMOTION PARTS UJT49210, among others listed above.

This table covers the Universal Joint U-Bolt kits. Read more

This group shows a single part: WJB / INMOTION PARTS UJT33010.