2019 Toyota Sequoia Drivetrain Parts

This table covers the actuators that engage four-wheel drive at the transfer case or axle. Typical signs include a door or range that will not move, or a click with no motion. Confirm the command signal before replacing the actuator — a failed module looks the same. Read more

2 4WD Actuator parts are listed for the 2019 Toyota Sequoia, from STANDARD MOTOR PRODUCTS and WELLS.

Part numbers include STANDARD MOTOR PRODUCTS TCA104 and WELLS 1S15514.

This table covers the seals at the Axle Intermediate Shaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

One part is listed for the 2019 Toyota Sequoia — TIMKEN 710595.

This table covers the seals where an axle shaft exits the housing. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

11 Axle Shaft Seal parts for the 2019 Toyota Sequoia come from 6 brands — NATIONAL, SKF, BCA and 3 other brands. The "Popular" part is NATIONAL 710596.

This table covers the complete CV axle shafts from differential (or hub) to wheel. Typical signs include a click in tight turns, grease flung around the wheel well, or a vibration that builds with speed. A torn boot caught early is a boot kit; caught late it is the whole axle. Torque the axle nut to the method in the notes. Read more

14 CV Axle parts for the 2019 Toyota Sequoia come from 5 brands — GSP, CARDONE, TRAKMOTIVE and 2 other brands. The "Popular" part is APWI TO8363.

The Economy section lists 1 option from CARDONE — the catalog's value-priced group. CARDONE 605252 is listed in this group.

In the Heavy Duty grade, GSP and TRAKMOTIVE supply 2 parts: rated for severe service. A representative part number is GSP NCV69164XD.

In the Specialty - For Lifted Vehicles grade, GSP, TOP NOTCH and TRAKMOTIVE supply 3 parts: grouped under the catalog's "Specialty - For Lifted Vehicles" designation — the notes column spells out what sets them apart. A representative part number is GSP NCV69164XDP.

In the Standard Replacement grade, GSP, CARDONE, APWI and 2 other brands supply 8 parts: built to original-equipment specification. A representative part number is APWI TO8363.

This table covers the CV Intermediate shafts. Read more

One part is listed for the 2019 Toyota Sequoia — TRAKMOTIVE TO3512.

This table covers the boots that keep grease in a CV joint. Typical signs include a split boot, grease flung around the joint, or a click once grit is inside. A boot caught early is a kit. Once the joint has clicked, the joint itself is usually worn. Read more

2 CV Joint Boot parts for the 2019 Toyota Sequoia come from BECK/ARNLEY.

This group includes BECK/ARNLEY 1033133 and BECK/ARNLEY 1032872.

This table covers the Differential Carrier shims. Read more

MOTIVE GEAR supplies both parts for the 2019 Toyota Sequoia.

This group includes MOTIVE GEAR GM95MSK and MOTIVE GEAR GM95SSK.

This table covers the Differential Lock actuators. Typical signs include a door or range that will not move, or a click with no motion. Confirm the command signal before replacing the actuator — a failed module looks the same. Read more

This group shows a single part: DORMAN 600420.

This table covers the Differential mounts. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes. Read more

One part is listed for the 2019 Toyota Sequoia — BECK/ARNLEY 1042457.

This table covers the bearings and races on the differential pinion. Read more

SKF supplies both parts for the 2019 Toyota Sequoia.

This group includes SKF BR4090 and SKF BR911.

This table covers the wear sleeves used to restore a grooved pinion seal surface. Read more

2 Differential Pinion Repair Sleeve parts for the 2019 Toyota Sequoia come from WJB / INMOTION PARTS.

Part numbers include WJB / INMOTION PARTS WS99204 and WJB / INMOTION PARTS WS99181.

This table covers the seals at the differential pinion yoke. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

8 Differential Pinion Seal parts for the 2019 Toyota Sequoia come from 4 brands — NATIONAL, SKF, WJB / INMOTION PARTS and 1 other brand. The "Popular" part is NATIONAL 710734.

Listed part numbers: NATIONAL 710734, NATIONAL 710931 and NATIONAL 711186, plus the other parts above.

This table covers kits that group the bearings, races and seals for a differential rebuild. Read more

5 Differential Rebuild Kit parts are listed for the 2019 Toyota Sequoia, from BCA, MOTIVE GEAR and LUK. BCA NBDRK381MK carries the "Popular" badge.

In the Master Kit grade, BCA and MOTIVE GEAR supply 2 parts: grouped under the catalog's "Master Kit" designation — the notes column spells out what sets them apart. A representative part number is BCA NBDRK381MK.

The Standard Kit section lists 2 options from BCA and LUK — grouped under the catalog's "Standard Kit" designation — the notes column spells out what sets them apart. BCA NBDRK381 is listed in this group.

1 ungrouped part is not assigned to a grade, with the same engine-level match.

Part numbers include BCA NBDRK381MK, MOTIVE GEAR RT95RMK and BCA NBDRK381, among others listed above.

This table covers the ring-and-pinion gear sets that set the axle ratio. Read more

This group shows a single part: MOTIVE GEAR T9.

This table covers the driveshafts that carry torque from the transmission or transfer case. Read more

7 Drive Shaft parts are listed for the 2019 Toyota Sequoia, from DORMAN, WJB / INMOTION PARTS, GSP and 1 other brand. DORMAN 986149 carries the "Popular" badge.

Listed part numbers: DORMAN 986149, DORMAN 938339 and DORMAN 936744, plus the other parts above.

This table covers the gear oils specified for the axle or transfer case. Typical signs include a low-oil lamp, knocking, or oil that has gone thin before the next interval. Match the viscosity and spec in the notes, not just the weight on the bottle. Read more

3 Gear Oil parts for the 2019 Toyota Sequoia come from 2 brands — VALVOLINE and IDEMITSU.

Part numbers include IDEMITSU 30305024750, VALVOLINE 915052 and VALVOLINE 915053.

This table covers the fluids specified for the transfer case. Typical signs include discolored fluid, a burnt smell, or a level that keeps dropping. Use only the specification in the notes — the tables group grades because they are not interchangeable. Read more

13 Transfer Case Fluid parts for the 2019 Toyota Sequoia come from 5 brands — VALVOLINE, LUCAS OIL, MOBIL and 2 other brands. The "Popular" part is MOBIL 104361.

This table covers the seals at the Transfer Case Housing Extension. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

2 Transfer Case Housing Extension Seal parts are listed for the 2019 Toyota Sequoia, from NATIONAL and WJB / INMOTION PARTS.

This group includes NATIONAL 710932 and WJB / INMOTION PARTS WS710932.

This table covers the wear sleeves used to restore a Transfer Case Input Shaft seal surface. Read more

3 Transfer Case Input Shaft Repair Sleeve parts are listed for the 2019 Toyota Sequoia, from BCA, NATIONAL and WJB / INMOTION PARTS.

This group includes BCA NS99196, NATIONAL 99196 and WJB / INMOTION PARTS WS99196.

This table covers the seals at the Transfer Case Input Shaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

One part is listed for the 2019 Toyota Sequoia — WJB / INMOTION PARTS WS710956.

This table covers the Transfer Case motors. Typical signs include no motion, a squeal, or a motor that only runs on one speed. Confirm power, ground and the control module before replacing the motor. Read more

One part is listed for the 2019 Toyota Sequoia — DORMAN 600471.

This table covers the Transfer Case Mounting Adapter bearings. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

3 Transfer Case Mounting Adapter Bearing parts for the 2019 Toyota Sequoia come from 3 brands — WJB / INMOTION PARTS, BCA and NATIONAL.

The Economy section: 1 option from WJB / INMOTION PARTS. WJB / INMOTION PARTS RB6009 is listed in this group.

Standard Replacement: 2 parts, from BCA and NATIONAL. A representative part number is BCA NB109.

Listed part numbers: WJB / INMOTION PARTS RB6009, BCA NB109 and NATIONAL 109.

This table covers the seals at the Transfer Case Mounting Adapter. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

3 Transfer Case Mounting Adapter Seal parts are listed for the 2019 Toyota Sequoia, from BCA, NATIONAL and WJB / INMOTION PARTS.

Listed part numbers: BCA NS710265, NATIONAL 710265 and WJB / INMOTION PARTS WS710265.

This table covers the Transfer Case Output Shaft bearings. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

5 Transfer Case Output Shaft Bearing parts are listed for the 2019 Toyota Sequoia, from BCA, WJB / INMOTION PARTS, NATIONAL and 1 other brand. WJB / INMOTION PARTS RB6208 carries the "Popular" badge.

Economy: 1 part, from WJB / INMOTION PARTS. A representative part number is WJB / INMOTION PARTS RB6208.

The Standard Replacement section: 4 options from BCA, NATIONAL and SCHAEFFLER. BCA NB208S is listed in this group.

This group includes WJB / INMOTION PARTS RB6208, BCA NB208S and BCA NB208 and the remaining parts above.

This table covers the seals at the Transfer Case Output Shaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

4 Transfer Case Output Shaft Seal parts for the 2019 Toyota Sequoia come from 3 brands — NATIONAL, SCHAEFFLER and WJB / INMOTION PARTS.

Listed part numbers: NATIONAL 710957, NATIONAL 710956 and SCHAEFFLER SS6637, plus the other parts above.

This table covers the U-joints in the driveshaft. Read more

33 Universal Joint parts for the 2019 Toyota Sequoia come from 7 brands — MOOG, SKF, DANA and 4 other brands. The "Popular" part is MOOG 270. They are grouped as Economy, Heavy Duty and Standard Replacement, with Standard Replacement the largest group at 16 parts from MOOG, SKF, GMB and 4 other brands.