2019 Dodge Challenger Drivetrain Parts

This table covers the actuators that engage four-wheel drive at the transfer case or axle. Typical signs include a door or range that will not move, or a click with no motion. Confirm the command signal before replacing the actuator — a failed module looks the same. Read more

This group shows a single part: STANDARD MOTOR PRODUCTS TCA118.

This table covers the Axle / Differential assemblies. Read more

7 Axle / Differential Assembly parts for the 2019 Dodge Challenger come from MOPAR. 1 part fits every engine; the other 6 are engine-specific.

This group includes MOPAR 68159834AH, MOPAR 68494250AC and MOPAR 68427796AA and the remaining parts above.

This table covers the Axle housings. Read more

One part is listed for the 2019 Dodge Challenger — MOPAR 5143949AA.

This table covers the seals where an axle shaft exits the housing. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

7 Axle Shaft Seal parts are listed for the 2019 Dodge Challenger, from TIMKEN and ELRING. TIMKEN SL260185 carries the "Popular" badge.

Listed part numbers: TIMKEN SL260185, ELRING B12920 and TIMKEN SL260192, plus the other parts above.

This table covers the complete CV axle shafts from differential (or hub) to wheel. Typical signs include a click in tight turns, grease flung around the wheel well, or a vibration that builds with speed. A torn boot caught early is a boot kit; caught late it is the whole axle. Torque the axle nut to the method in the notes. Read more

40 CV Axle parts are listed for the 2019 Dodge Challenger, from MOPAR, TRAKMOTIVE, TOP NOTCH and 4 other brands. FAMOUS BRAND NCV479097 carries the "Popular" badge. Grades run from Economy through Standard Replacement; Standard Replacement is the most populated section, led by MOPAR, TRAKMOTIVE, TOP NOTCH and 2 other brands.

This table covers the CV Intermediate shafts. Read more

This group shows a single part: DORMAN 630347.

This table covers the constant-velocity joints at each end of a drive axle. Read more

One part is listed for the 2019 Dodge Challenger — AAM 40204687.

This table covers the boots that keep grease in a CV joint. Typical signs include a split boot, grease flung around the joint, or a click once grit is inside. A boot caught early is a kit. Once the joint has clicked, the joint itself is usually worn. Read more

MOPAR supplies both parts for the 2019 Dodge Challenger. All of them fit every engine offered in the 2019 Challenger.

Listed part numbers: MOPAR 5142215AA and MOPAR 5142216AA.

This table covers the bearings and races that support the differential carrier. Read more

One part is listed for the 2019 Dodge Challenger — MOPAR 5143952AA.

This table covers the Differential covers. Read more

This group shows a single part: MOPAR 5143120AA.

This table covers the Differential Cover bolts. Read more

One part is listed for the 2019 Dodge Challenger — MOPAR 5143143AA.

This table covers the gaskets that seal the Differential Cover. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

One part is listed for the 2019 Dodge Challenger — ELRING B12900.

This table covers the Differential mounts. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes. Read more

4 Differential Mount parts for the 2019 Dodge Challenger come from MOPAR. 1 part fits every engine; the other 3 are engine-specific.

Part numbers include MOPAR 68242689AA, MOPAR 68242690AA and MOPAR 68199993AB, among others listed above.

This table covers the flanges that connect the driveshaft to the differential pinion. Read more

One part is listed for the 2019 Dodge Challenger — MOPAR 68259626AA.

This table covers the seals at the differential pinion yoke. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

2 Differential Pinion Seal parts are listed for the 2019 Dodge Challenger, from SKF and WJB / INMOTION PARTS. All of them fit every engine offered in the 2019 Challenger.

Part numbers include SKF 19877A and WJB / INMOTION PARTS WS19877A.

This table covers the Differential Pinion shims. Read more

MOPAR supplies the 5 Differential Pinion Shim parts for the 2019 Dodge Challenger. All of them fit every engine offered in the 2019 Challenger.

This group includes MOPAR 5142921AA, MOPAR 5142922AA and MOPAR 5142923AA and the remaining parts above.

This table covers the seals at the Differential. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

6 Differential Seal parts for the 2019 Dodge Challenger come from 2 brands — ELRING and MOPAR. The "Popular" part is MOPAR 5161591AA. 3 parts fit every engine; the other 3 are engine-specific.

Part numbers include MOPAR 5161591AA, ELRING B12950 and ELRING B12970, among others listed above.

This table covers the driveshafts that carry torque from the transmission or transfer case. Read more

21 Drive Shaft parts for the 2019 Dodge Challenger come from 7 brands — MOPAR, DORMAN, TOP NOTCH and 4 other brands. The "Popular" part is DORMAN 986031.

This table covers the seals at the Drive Shaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

2 Drive Shaft Seal parts are listed for the 2019 Dodge Challenger, from ELRING and MOPAR. All of them fit every engine offered in the 2019 Challenger.

Listed part numbers: ELRING B15340 and MOPAR 5143144AA.

This table covers the gear oils specified for the axle or transfer case. Typical signs include a low-oil lamp, knocking, or oil that has gone thin before the next interval. Match the viscosity and spec in the notes, not just the weight on the bottle. Read more

16 Gear Oil parts are listed for the 2019 Dodge Challenger, from VALVOLINE, LUCAS OIL, MOPAR and 3 other brands. LUCAS OIL 10047 carries the "Popular" badge. 1 part fits every engine; the other 15 are engine-specific.

In the SAE 75W-85 grade, MOPAR supplies 2 parts: grouped under the catalog's "SAE 75W-85" designation — the notes column spells out what sets them apart. A representative part number is MOPAR 68232947AC.

In the SAE 75W-90 grade, LUCAS OIL, VALVOLINE, MOBIL and 2 other brands supply 11 parts: grouped under the catalog's "SAE 75W-90" designation — the notes column spells out what sets them apart. A representative part number is LUCAS OIL 10047.

3 ungrouped parts are not assigned to a grade, with the same engine-level match.

This table covers the Transfer Case control modules. Read more

This group shows a single part: MOPAR 68528334AB.

This table covers the fluids specified for the transfer case. Typical signs include discolored fluid, a burnt smell, or a level that keeps dropping. Use only the specification in the notes — the tables group grades because they are not interchangeable. Read more

4 Transfer Case Fluid parts are listed for the 2019 Dodge Challenger, from MOPAR, VAICO and VALVOLINE.

This group includes MOPAR 68049954AD, MOPAR 68049954AC and VAICO V600432 and the remaining parts above.

This table covers the wear sleeves used to restore a Transfer Case Input Shaft seal surface. Read more

2 Transfer Case Input Shaft Repair Sleeve parts for the 2019 Dodge Challenger come from 2 brands — NATIONAL and WJB / INMOTION PARTS.

This group includes NATIONAL 99274 and WJB / INMOTION PARTS WS99274.

This table covers the Transfer Case Main Shaft Pilot bearings. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

2 Transfer Case Main Shaft Pilot Bearing parts for the 2019 Dodge Challenger come from 2 brands — WJB / INMOTION PARTS and NATIONAL.

The Economy section lists 1 option from WJB / INMOTION PARTS — the catalog's value-priced group. WJB / INMOTION PARTS WTA16 is listed in this group.

In the Standard Replacement grade, NATIONAL supplies 1 part: built to original-equipment specification. A representative part number is NATIONAL A16.

Part numbers include WJB / INMOTION PARTS WTA16 and NATIONAL A16.

This table covers the Transfer Case Output shafts. Read more

This group shows a single part: MOPAR 68055317AA.

This table covers the Transfer Case Output Shaft bearings. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

6 Transfer Case Output Shaft Bearing parts for the 2019 Dodge Challenger come from 3 brands — WJB / INMOTION PARTS, BCA and NATIONAL. The "Popular" part is WJB / INMOTION PARTS RB6207.

The Economy section: 2 options from WJB / INMOTION PARTS. WJB / INMOTION PARTS RB6207 is listed in this group.

Standard Replacement: 4 parts, from BCA and NATIONAL. A representative part number is BCA WE61445.

This group includes WJB / INMOTION PARTS RB6207, WJB / INMOTION PARTS RB6208 and BCA WE61445 and the remaining parts above.

This table covers the wear sleeves used to restore a Transfer Case Output Shaft seal surface. Read more

3 Transfer Case Output Shaft Repair Sleeve parts are listed for the 2019 Dodge Challenger, from BCA, NATIONAL and WJB / INMOTION PARTS. 1 part fits every engine; the other 2 are engine-specific.

This group includes BCA NS99189, NATIONAL 99189 and WJB / INMOTION PARTS WS99189.

This table covers the seals at the Transfer Case Output Shaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

4 Transfer Case Output Shaft Seal parts are listed for the 2019 Dodge Challenger, from BCA, NATIONAL, SCHAEFFLER and 1 other brand. 2 parts fit every engine; the other 2 are engine-specific.

Listed part numbers: BCA NS710661, NATIONAL 710661 and SCHAEFFLER SS2949, plus the other parts above.

This table covers the seals at the Transfer Case Shift Shaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

2 Transfer Case Shift Shaft Seal parts for the 2019 Dodge Challenger come from 2 brands — NATIONAL and WJB / INMOTION PARTS.

Listed part numbers: NATIONAL 330385 and WJB / INMOTION PARTS WS330385.