1979 Honda Accord Engine Parts

This table covers the Auxiliary valves. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

This group shows a single part: ITM ENGINE COMPONENTS RV9252.

This table covers the camshafts that open the valves. Read more

One part is listed for the 1979 Honda Accord — ITM ENGINE COMPONENTS 0562240.

This table covers the wear sleeves used to restore a Camshaft seal surface. Read more

This group shows a single part: TIMKEN KWK99106.

This table covers the seals at each camshaft end. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

11 Camshaft Seal parts for the 1979 Honda Accord come from 11 brands — MAHLE / CLEVITE, TIMKEN, WJB / INMOTION PARTS and 8 other brands. The "Popular" part is MAHLE / CLEVITE 66580.

This table covers the connecting rods between each piston and the crankshaft. Read more

One part is listed for the 1979 Honda Accord — TOPLINE CRH9.

This table covers the bearings in the connecting-rod big ends. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

4 Connecting Rod Bearing parts are listed for the 1979 Honda Accord, from ITM ENGINE COMPONENTS, KING ENGINE BEARINGS, MAHLE / CLEVITE and 1 other brand.

Listed part numbers: ITM ENGINE COMPONENTS 4B1951, KING ENGINE BEARINGS CR4463AM and MAHLE / CLEVITE CB1223P, plus the other parts above.

This table covers lower / conversion gasket sets for oil-pan and related joints. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

4 Conversion / Lower Gasket Set parts are listed for the 1979 Honda Accord, from AJUSA, APEX, FEL-PRO and 1 other brand.

Listed part numbers: AJUSA 54035900, APEX ACS1004 and FEL-PRO CS8736, plus the other parts above.

This table covers the main bearings that support the crankshaft in the block. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

6 Crankshaft Main Bearing parts for the 1979 Honda Accord come from 3 brands — KING ENGINE BEARINGS, ITM ENGINE COMPONENTS and TOPLINE. The "Popular" part is ITM ENGINE COMPONENTS 5M9502.

The High Performance section lists 1 option from KING ENGINE BEARINGS — engineered beyond original-equipment specification. KING ENGINE BEARINGS MB5168XP is listed in this group.

In the Standard Replacement grade, ITM ENGINE COMPONENTS, TOPLINE and KING ENGINE BEARINGS supply 5 parts: built to original-equipment specification. A representative part number is ITM ENGINE COMPONENTS 5M9502.

Listed part numbers: ITM ENGINE COMPONENTS 5M9502, KING ENGINE BEARINGS MB5168XP and KING ENGINE BEARINGS MB5168AM, plus the other parts above.

This table covers the sleeves used to restore a grooved crankshaft seal surface. Read more

5 Crankshaft Repair Sleeve parts for the 1979 Honda Accord come from 5 brands — NATIONAL, BCA, SKF and 2 other brands. The "Popular" part is NATIONAL 99139.

This group includes NATIONAL 99139, BCA NS99139 and SKF 99296 and the remaining parts above.

This table covers the front and rear seals that keep oil in at the crankshaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

8 Crankshaft Seal parts for the 1979 Honda Accord come from 7 brands — ITM ENGINE COMPONENTS, TIMKEN, APEX and 4 other brands. The "Popular" part is ITM ENGINE COMPONENTS 1500902.

Listed part numbers: ITM ENGINE COMPONENTS 1500902, TIMKEN 3771 and APEX ABS101, plus the other parts above.

This table covers the head gaskets that seal the block to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

4 Cylinder Head Gasket parts are listed for the 1979 Honda Accord, from AJUSA, APEX, BECK/ARNLEY and 1 other brand.

Part numbers include AJUSA 10021800, APEX AHG104 and BECK/ARNLEY 0322679, among others listed above.

This table covers multi-piece gasket sets for a cylinder-head job. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

5 Cylinder Head Gasket Set parts are listed for the 1979 Honda Accord, from APEX, AJUSA, ITM ENGINE COMPONENTS and 2 other brands. APEX AHS1004 carries the "Popular" badge.

Listed part numbers: APEX AHS1004, AJUSA 52063700 and ITM ENGINE COMPONENTS 0910906, plus the other parts above.

This table covers the wear sleeves used to restore a Cylinder seal surface. Read more

MELLING supplies both parts for the 1979 Honda Accord.

Listed part numbers: MELLING CSL2216 and MELLING CSL1116.

This table covers the block heaters that warm the coolant or oil in cold weather. Read more

This group shows a single part: KAT'S HEATERS 11411.

This table covers full gasket kits covering the joints opened in an engine rebuild. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

3 Engine Kit Gasket Set parts are listed for the 1979 Honda Accord, from AJUSA, APEX and ITM ENGINE COMPONENTS.

Listed part numbers: AJUSA 50071700, APEX AFS1004 and ITM ENGINE COMPONENTS 0900907.

This table covers the exhaust valves that let combustion gas out of the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

3 Exhaust Valve parts for the 1979 Honda Accord come from 3 brands — ITM ENGINE COMPONENTS, SEALED POWER and TOPLINE.

This group includes ITM ENGINE COMPONENTS RX9367, SEALED POWER V2243X and TOPLINE EVH9L.

This table covers the Expansion plugs. Typical signs include a leak at the drain or glow-plug hole, or a plug that has rounded off. Replace the crush washer and torque to the spec in the notes. Read more

11 Expansion Plug parts are listed for the 1979 Honda Accord, from DORMAN, PIONEER, QUALCAST and 2 other brands. DORMAN 555100 carries the "Popular" badge. 1 part fits every engine; the other 10 are engine-specific.

This table covers the Intake & Exhaust Manifold gasket sets. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

2 Intake & Exhaust Manifold Gasket Set parts are listed for the 1979 Honda Accord, from AJUSA and APEX.

Part numbers include AJUSA 13064000 and APEX AMS1040.

This table covers the gaskets between the intake manifold and the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

One part is listed for the 1979 Honda Accord — ITM ENGINE COMPONENTS 0950908.

This table covers the intake valves that let air (and fuel, on port-injected engines) into the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

7 Intake Valve parts for the 1979 Honda Accord come from 5 brands — BECK/ARNLEY, SEALED POWER, ITM ENGINE COMPONENTS and 2 other brands. The "Popular" part is BECK/ARNLEY 0212910.

This group includes BECK/ARNLEY 0212910, BECK/ARNLEY 0212894 and ITM ENGINE COMPONENTS RV35070 and the remaining parts above.

This table covers the mounts that hold the engine to the chassis. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes. Read more

6 Motor Mount parts for the 1979 Honda Accord come from 4 brands — DEA / MARMON RIDE CONTROL, WESTAR, ANCHOR and 1 other brand. The "Popular" part is DEA / MARMON RIDE CONTROL A2450.

This group includes DEA / MARMON RIDE CONTROL A2450, WESTAR EM8660 and ANCHOR 8012 and the remaining parts above.

This table covers the Oil Cooler Mounting kits. Read more

HAYDEN supplies both parts for the 1979 Honda Accord.

This group includes HAYDEN 238 and HAYDEN 153.

This table covers the drain plugs in the oil pan. Read more

4 Oil Drain Plug parts for the 1979 Honda Accord come from 2 brands — DORMAN and AGS. 1 part fits every engine; the other 3 are engine-specific.

Part numbers include AGS ODP00019, DORMAN 090080 and DORMAN 090040, among others listed above.

This table covers the crush washers and gaskets under the oil drain plug. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

4 Oil Drain Plug Gasket parts are listed for the 1979 Honda Accord, from DORMAN and AJUSA.

Listed part numbers: AJUSA 22009300, DORMAN 097831CD and DORMAN 095023, plus the other parts above.

This table covers the caps on the oil filler neck. Read more

This group shows a single part: MOTORAD MO106.

This table covers the oil filters that screw onto this engine's filter mount. Typical signs include low oil pressure after a service, or a filter that will not spin off because the old gasket stayed on the block. Lube the new gasket and tighten to the spec on the box; a double-gasket install dumps the sump on the first drive. Read more

15 Oil Filter parts for the 1979 Honda Accord come from 11 brands — VARIOUS MFR, CHAMP / LUBER-FINER, FAMOUS BRAND and 8 other brands. The "Popular" part is VARIOUS MFR PG4651.

The Economy section lists 11 options from CHAMP / LUBER-FINER, FAMOUS BRAND, VARIOUS MFR and 6 other brands — the catalog's value-priced group. VARIOUS MFR PG4651 is listed in this group.

Standard Replacement: 4 parts, from VARIOUS MFR, WIX, FRAM and 1 other brand. A representative part number is VARIOUS MFR PG4651EX.

This table covers the gaskets between the oil pan and the block. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

3 Oil Pan Gasket parts for the 1979 Honda Accord come from 3 brands — AJUSA, APEX and ITM ENGINE COMPONENTS.

This group includes AJUSA 14029600, APEX AOP101 and ITM ENGINE COMPONENTS 0990902.

This table covers the Oil pumps. Typical signs include noise from the pump, no pressure, or fluid that never arrives at the outlet. Prime or fill the pump as the notes require. A dry start is a common way to kill a new unit. Read more

3 Oil Pump parts for the 1979 Honda Accord come from 3 brands — ITM ENGINE COMPONENTS, MELLING and SEALED POWER.

This group includes ITM ENGINE COMPONENTS 057840, MELLING M96F and SEALED POWER 22441989.

This table covers the Oil Temperature senders. Read more

One part is listed for the 1979 Honda Accord — AUTO-TUNE PT3441.

This table covers the pistons that travel in each cylinder. Typical signs include knock, blow-by, or a cylinder that will not hold compression. Piston work is a short-block job. Match bore, pin and ring pack in the notes — not the photo. Read more

One part is listed for the 1979 Honda Accord — ITM ENGINE COMPONENTS RY6113.

This table covers the rings that seal each piston to the cylinder wall. Read more

7 Piston Ring parts are listed for the 1979 Honda Accord, from HASTINGS MANUFACTURING, SEALED POWER, ITM ENGINE COMPONENTS and 1 other brand. SEALED POWER E402KC carries the "Popular" badge.

The Premium section lists 1 option from SEALED POWER — a step above OE specification in materials, tolerances or warranty terms. SEALED POWER E402KC is listed in this group.

The Standard Replacement section: 6 options from HASTINGS MANUFACTURING, ITM ENGINE COMPONENTS and TOPLINE. HASTINGS MANUFACTURING 2C6134 is listed in this group.

This group includes SEALED POWER E402KC, HASTINGS MANUFACTURING 2C6134 and HASTINGS MANUFACTURING 6134 and the remaining parts above.

This table covers the rocker arms that transfer cam motion to the valves. Read more

2 Rocker Arm parts for the 1979 Honda Accord come from 2 brands — ITM ENGINE COMPONENTS and SEALED POWER.

This group includes ITM ENGINE COMPONENTS 0566012 and SEALED POWER R993.

This table covers the Thrust washers. Read more

3 Thrust Washer parts for the 1979 Honda Accord come from 3 brands — ITM ENGINE COMPONENTS, KING ENGINE BEARINGS and MAHLE / CLEVITE.

This group includes ITM ENGINE COMPONENTS 1T1952, KING ENGINE BEARINGS TW110AM and MAHLE / CLEVITE TW327S.

This table covers the Timing belts. Typical signs include squeal on cold start, cracked ribs, or glazing. Spin the tensioner and idlers by hand while the belt is off. Read more

3 Timing Belt parts are listed for the 1979 Honda Accord, from ITM ENGINE COMPONENTS, ACDELCO and S.A. GEAR.

Economy: 1 part, from ITM ENGINE COMPONENTS. A representative part number is ITM ENGINE COMPONENTS 4041.

The Standard Replacement section: 2 options from ACDELCO and S.A. GEAR. ACDELCO TB041 is listed in this group.

This group includes ITM ENGINE COMPONENTS 4041 and ACDELCO TB041 and the remaining parts above.

This table covers the Timing Belt pulleys. Typical signs include a growl or chirp that follows engine speed, or a pulley that will not spin freely by hand. Spin each pulley with the belt off. Roughness or play means replace it with the belt. Read more

2 Timing Belt Pulley parts for the 1979 Honda Accord come from BECK/ARNLEY.

Listed part numbers: BECK/ARNLEY 0513860 and BECK/ARNLEY 0513954.

This table covers the Timing Belt tensioners. Typical signs include belt flutter, a chirp that returns after a new belt, or an arm that no longer damps. Replace the tensioner with the belt at higher mileage. Read more

This group shows a single part: S.A. GEAR 9090.

This table covers the Timing Cam sprockets. Read more

This group shows a single part: ITM ENGINE COMPONENTS 50063.

This table covers the tensioners that keep the timing chain taut. Typical signs include belt flutter, a chirp that returns after a new belt, or an arm that no longer damps. Replace the tensioner with the belt at higher mileage. Read more

This group shows a single part: ITM ENGINE COMPONENTS 60045.

This table covers the gaskets that seal the Timing Cover. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

3 Timing Cover Gasket parts for the 1979 Honda Accord come from 2 brands — APEX and ITM ENGINE COMPONENTS.

Listed part numbers: APEX ATC1010, APEX ATC1040 and ITM ENGINE COMPONENTS 0980902.

This table covers the wear sleeves used to restore a Timing Cover seal surface. Read more

This group shows a single part: SKF 99138.

This table covers the seals at the Timing Cover. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

2 Timing Cover Seal parts for the 1979 Honda Accord come from 2 brands — ITM ENGINE COMPONENTS and SKF.

Listed part numbers: ITM ENGINE COMPONENTS 1506101 and SKF 13907.

This table covers the Torque Strut bushings. Typical signs include a clunk over bumps, or a torn or walked-out bushing you can see. Press the new bushing square. A cocked bushing will tear in a few thousand miles. Read more

4 Torque Strut Bushing parts for the 1979 Honda Accord come from 2 brands — DEA / MARMON RIDE CONTROL and PIONEER.

This group includes DEA / MARMON RIDE CONTROL A6539, DEA / MARMON RIDE CONTROL A6540 and PIONEER 628293 and the remaining parts above.

This table covers the Torque Strut mounts. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes. Read more

3 Torque Strut Mount parts are listed for the 1979 Honda Accord, from ANCHOR and WESTAR.

This group includes ANCHOR 8029, ANCHOR 8293 and WESTAR EM8293.

This table covers the gaskets that seal the valve cover to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

5 Valve Cover Gasket parts for the 1979 Honda Accord come from 5 brands — FEL-PRO, AJUSA, APEX and 2 other brands. The "Popular" part is FEL-PRO VS50199R.

Listed part numbers: FEL-PRO VS50199R, AJUSA 56015900 and APEX AVC104, plus the other parts above.

This table covers the Valve Cover grommets. Read more

4 Valve Cover Grommet parts for the 1979 Honda Accord come from 4 brands — APEX, FEL-PRO, JAPANESE OE and 1 other brand.

Part numbers include APEX AES100, FEL-PRO ES70337 and JAPANESE OE KF81126, among others listed above.

This table covers the pressed-in bronze and cast-iron guides that align valve stems. Typical signs include oil smoke on startup, a guide that has gone oval, or a valve that no longer seats quietly. Guides are a machine-shop fit. Confirm stem diameter in the notes before ordering. Read more

5 Valve Guide parts for the 1979 Honda Accord come from 3 brands — ITM ENGINE COMPONENTS, QUALCAST and SEALED POWER. The "Popular" part is ITM ENGINE COMPONENTS VG972BR.

This group includes ITM ENGINE COMPONENTS VG972BR, ITM ENGINE COMPONENTS VG972CI and QUALCAST 307710 and the remaining parts above.

This table covers the Valve seats. Read more

4 Valve Seat parts are listed for the 1979 Honda Accord, from PIONEER and QUALCAST.

This group includes PIONEER 38510, PIONEER 38520 and QUALCAST 21125052 and the remaining parts above.

This table covers the springs that close each intake and exhaust valve. Typical signs include a sagging corner, a broken coil, or a clunk from the spring pocket. Replace springs in axle pairs and inspect the seats. Read more

5 Valve Spring parts are listed for the 1979 Honda Accord, from ITM ENGINE COMPONENTS and SEALED POWER.

Listed part numbers: ITM ENGINE COMPONENTS VS1131, ITM ENGINE COMPONENTS VS1133 and ITM ENGINE COMPONENTS VS1132, plus the other parts above.

This table covers the Valve Spring retainers. Read more

One part is listed for the 1979 Honda Accord — ITM ENGINE COMPONENTS 051135.

This table covers the keepers that lock each valve-spring retainer to the stem. Read more

2 Valve Spring Retainer Keeper parts are listed for the 1979 Honda Accord, from ITM ENGINE COMPONENTS and PIONEER.

This group includes ITM ENGINE COMPONENTS 051134 and PIONEER PF235.

This table covers the seals on each valve stem that control oil into the guides. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

11 Valve Stem Seal parts for the 1979 Honda Accord come from 6 brands — FEL-PRO, ITM ENGINE COMPONENTS, TOPLINE and 3 other brands. The "Popular" part is FEL-PRO SS72552.