2016 Honda Accord Engine Parts

This table covers the wear sleeves used to restore a Camshaft seal surface. Read more

3 Camshaft Repair Sleeve parts are listed for the 2016 Honda Accord, from BCA, NATIONAL and WJB / INMOTION PARTS.

Part numbers include BCA NS99147, NATIONAL 99147 and WJB / INMOTION PARTS WS99147.

This table covers the seals at each camshaft end. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

11 Camshaft Seal parts are listed for the 2016 Honda Accord, from VICTOR REINZ, FEL-PRO, MAHLE / CLEVITE and 7 other brands. FEL-PRO TCS46025 carries the "Popular" badge.

This table covers lower / conversion gasket sets for oil-pan and related joints. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

5 Conversion / Lower Gasket Set parts for the 2016 Honda Accord come from 5 brands — FEL-PRO, AJUSA, APEX and 2 other brands. The "Popular" part is FEL-PRO CS26265.

Part numbers include FEL-PRO CS26265, AJUSA 54253700 and APEX ACS1055, among others listed above.

This table covers the main bearings that support the crankshaft in the block. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

3 Crankshaft Main Bearing parts are listed for the 2016 Honda Accord, from TOPLINE and KING ENGINE BEARINGS.

This group includes KING ENGINE BEARINGS MB4508SI, TOPLINE TWH37 and TOPLINE MBH37.

This table covers the sleeves used to restore a grooved crankshaft seal surface. Read more

One part is listed for the 2016 Honda Accord — WJB / INMOTION PARTS WS99317.

This table covers the front and rear seals that keep oil in at the crankshaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

20 Crankshaft Seal parts are listed for the 2016 Honda Accord, from ELRING, MAHLE / CLEVITE, VICTOR REINZ and 9 other brands. FEL-PRO BS40685 carries the "Popular" badge.

This table covers the bolts that clamp the cylinder head to the block. Read more

7 Cylinder Head Bolt parts for the 2016 Honda Accord come from 6 brands — VICTOR REINZ, APEX, FEL-PRO and 3 other brands. The "Popular" part is APEX AHB155.

Part numbers include APEX AHB155, FEL-PRO ES713291 and AJUSA 81067500, among others listed above.

This table covers the head gaskets that seal the block to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

13 Cylinder Head Gasket parts for the 2016 Honda Accord come from 7 brands — FEL-PRO, AJUSA, APEX and 4 other brands. The "Popular" part is FEL-PRO 26510PT.

This table covers multi-piece gasket sets for a cylinder-head job. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

6 Cylinder Head Gasket Set parts for the 2016 Honda Accord come from 5 brands — ELRING, APEX, ITM ENGINE COMPONENTS and 2 other brands. The "Popular" part is APEX AHS1069.

This group includes APEX AHS1069, ITM ENGINE COMPONENTS 0916272 and ELRING 893900 and the remaining parts above.

This table covers the block heaters that warm the coolant or oil in cold weather. Read more

KAT'S HEATERS supplies both parts for the 2016 Honda Accord.

Listed part numbers: KAT'S HEATERS 11419 and KAT'S HEATERS 28500.

This table covers the Engine covers. Read more

5 Engine Cover parts for the 2016 Honda Accord come from 2 brands — TECHPRO and VARIOUS MFR.

This group includes TECHPRO HO1228140, TECHPRO HO1228141 and TECHPRO HO1228158 and the remaining parts above.

This table covers full gasket kits covering the joints opened in an engine rebuild. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

2 Engine Kit Gasket Set parts for the 2016 Honda Accord come from 2 brands — AJUSA and TOPLINE.

Listed part numbers: AJUSA 50441500 and TOPLINE CGSH51.

This table covers the exhaust valves that let combustion gas out of the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

7 Exhaust Valve parts are listed for the 2016 Honda Accord, from MELLING, ITM ENGINE COMPONENTS, MAHLE / CLEVITE and 3 other brands. ITM ENGINE COMPONENTS RX9599 carries the "Popular" badge.

This group includes ITM ENGINE COMPONENTS RX9599, MELLING V0779 and MAHLE / CLEVITE 2114674 and the remaining parts above.

This table covers the crankshaft pulleys / harmonic balancers at the front of the engine. Read more

2 Harmonic Balancer parts for the 2016 Honda Accord come from 2 brands — ATP and DAYCO.

This group includes ATP 102367 and DAYCO PB1713N.

This table covers the gaskets between the intake manifold and the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

8 Intake Manifold Gasket parts for the 2016 Honda Accord come from 6 brands — BECK/ARNLEY, ELRING, APEX and 3 other brands. The "Popular" part is APEX AMS1691.

Part numbers include APEX AMS1691, MAHLE / CLEVITE MS19696 and BECK/ARNLEY 0376217, among others listed above.

This table covers the gaskets that seal the Intake Plenum. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

6 Intake Plenum Gasket parts are listed for the 2016 Honda Accord, from VICTOR REINZ, FEL-PRO, MAHLE / CLEVITE and 2 other brands. FEL-PRO MS964093 carries the "Popular" badge.

Listed part numbers: FEL-PRO MS964093, MAHLE / CLEVITE MS19700 and APEX AMS1690, plus the other parts above.

This table covers the mounts that hold the engine to the chassis. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes. Read more

20 Motor Mount parts are listed for the 2016 Honda Accord, from DEA / MARMON RIDE CONTROL, ANCHOR, PIONEER and 3 other brands. SKP SKM9737 carries the "Popular" badge.

In the Economy grade, SKP supplies 2 parts: the catalog's value-priced group. A representative part number is SKP SKM9737.

The Standard Replacement section lists 18 options from DEA / MARMON RIDE CONTROL, ANCHOR, PIONEER and 2 other brands — built to original-equipment specification. ANCHOR 9998 is listed in this group.

This table covers the Motor Mount kits. Read more

One part is listed for the 2016 Honda Accord — ANCHOR 300478.

This table covers the engine oils listed by grade and specification for this engine. Typical signs include a low-oil lamp, knocking after a long interval, or oil that has gone thin and black well before the next service. Match the viscosity and spec in the notes (and on the filler cap). The tables group grades — they are not interchangeable. Read more

36 Oil parts are listed for the 2016 Honda Accord, from LIQUI MOLY, VALVOLINE, MOBIL and 3 other brands. LIQUI MOLY 22044 carries the "Popular" badge. Grades run from Full Synthetic through High Mileage (>75,000 Miles); Full Synthetic is the most populated section, led by LIQUI MOLY, VALVOLINE, PENTOSIN and 3 other brands.

This table covers the Oil Dipstick tubes. Read more

One part is listed for the 2016 Honda Accord — DORMAN 917387.

This table covers the drain plugs in the oil pan. Read more

8 Oil Drain Plug parts are listed for the 2016 Honda Accord, from DORMAN, ELRING, AGS and 2 other brands. DORMAN 090033 carries the "Popular" badge.

Listed part numbers: DORMAN 090033, DORMAN 090053 and AGS ODP00007, plus the other parts above.

This table covers the crush washers and gaskets under the oil drain plug. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

6 Oil Drain Plug Gasket parts for the 2016 Honda Accord come from 6 brands — DORMAN, FEL-PRO, AJUSA and 3 other brands. The "Popular" part is DORMAN 095144.

Listed part numbers: DORMAN 095144, FEL-PRO 73346 and AJUSA 22007400, plus the other parts above.

This table covers the caps on the oil filler neck. Read more

4 Oil Filler Cap parts are listed for the 2016 Honda Accord, from CALORSTAT, DORMAN, GATES and 1 other brand.

This group includes CALORSTAT OC2335, DORMAN 80985 and GATES 31284 and the remaining parts above.

This table covers the Oil Filter Adapter Gasket O-rings. Typical signs include a seep at a fitting or a housing that weeps after a service. Lube the new O-ring with the fluid it will see, and do not roll it into the groove. Read more

3 Oil Filter Adapter Gasket / O-Ring parts for the 2016 Honda Accord come from 3 brands — APEX, FEL-PRO and MAHLE / CLEVITE.

This group includes APEX AOM6025, FEL-PRO ES74047 and MAHLE / CLEVITE B33360.

This table covers the Oil Filter Support tubes. Read more

This group shows a single part: AUTOTECNICA HA1416938.

This table covers the oil pans that hold the engine's oil sump. Read more

5 Oil Pan parts for the 2016 Honda Accord come from 5 brands — ACKOJA, ATP, DORMAN and 2 other brands.

Listed part numbers: ACKOJA A260108, ATP 103652 and DORMAN 264380, plus the other parts above.

This table covers the gaskets between the oil pan and the block. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

2 Oil Pan Gasket parts are listed for the 2016 Honda Accord, from FEL-PRO and VICTOR REINZ.

This group includes FEL-PRO OS30954T and VICTOR REINZ 703141410.

This table covers the seals at the Oil Pressure Sender / Switch. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

One part is listed for the 2016 Honda Accord — FEL-PRO 73196.

This table covers the Oil pumps. Typical signs include noise from the pump, no pressure, or fluid that never arrives at the outlet. Prime or fill the pump as the notes require. A dry start is a common way to kill a new unit. Read more

5 Oil Pump parts are listed for the 2016 Honda Accord, from ENGINETECH, SKP, MELLING and 2 other brands. MELLING M569 carries the "Popular" badge.

Economy: 2 parts, from ENGINETECH and SKP. A representative part number is ENGINETECH EPK200.

The Standard Replacement section: 1 option from MELLING. MELLING M569 is listed in this group.

2 ungrouped parts are not assigned to a grade, with the same engine-level match.

Listed part numbers: MELLING M569, ENGINETECH EPK200 and SKP SKM569, plus the other parts above.

This table covers the gaskets that seal the Oil Pump. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

2 Oil Pump Gasket parts for the 2016 Honda Accord come from 2 brands — AJUSA and ELRING.

Part numbers include AJUSA 01130500 and ELRING 967650.

This table covers the seals at the Oil Pump. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

4 Oil Pump Seal parts for the 2016 Honda Accord come from 4 brands — BCA, JAPANESE OE, NATIONAL and 1 other brand.

This group includes BCA NS711181, JAPANESE OE A6629 and NATIONAL 711181 and the remaining parts above.

This table covers the pistons that travel in each cylinder. Typical signs include knock, blow-by, or a cylinder that will not hold compression. Piston work is a short-block job. Match bore, pin and ring pack in the notes — not the photo. Read more

6 Piston parts for the 2016 Honda Accord come from 3 brands — ENGINETECH, MAHLE / CLEVITE and TOPLINE. The "Popular" part is ENGINETECH P4321.

In the Premium grade, ENGINETECH and MAHLE / CLEVITE supply 4 parts: a step above OE specification in materials, tolerances or warranty terms. A representative part number is ENGINETECH P4321.

Standard Replacement: 2 parts, from TOPLINE. A representative part number is TOPLINE PAH51.

Listed part numbers: ENGINETECH P4321, MAHLE / CLEVITE 2243916WR and ENGINETECH K43216P, plus the other parts above.

This table covers the rings that seal each piston to the cylinder wall. Read more

6 Piston Ring parts for the 2016 Honda Accord come from 5 brands — HASTINGS MANUFACTURING, ENGINETECH, MAHLE / CLEVITE and 2 other brands. The "Popular" part is ENGINETECH S89416.

Premium: 3 parts, from ENGINETECH, MAHLE / CLEVITE and SEALED POWER. A representative part number is ENGINETECH S89416.

Standard Replacement: 3 parts, from HASTINGS MANUFACTURING and ITM ENGINE COMPONENTS. A representative part number is HASTINGS MANUFACTURING 2C4972.

Listed part numbers: ENGINETECH S89416, MAHLE / CLEVITE 42250CP and SEALED POWER E985KC, plus the other parts above.

This table covers the Thrust washers. Read more

One part is listed for the 2016 Honda Accord — KING ENGINE BEARINGS TW1015SI.

This table covers the Timing belts. Typical signs include squeal on cold start, cracked ribs, or glazing. Spin the tensioner and idlers by hand while the belt is off. Read more

8 Timing Belt parts for the 2016 Honda Accord come from 7 brands — GATES, CLOYES, BANDO and 4 other brands. The "Popular" part is BANDO TB329.

The Economy section: 1 option from CLOYES. CLOYES B329 is listed in this group.

The High Performance section lists 1 option from GATES — engineered beyond original-equipment specification. GATES T329RB is listed in this group.

Standard Replacement: 6 parts, from BANDO, GATES, ACDELCO and 3 other brands. A representative part number is BANDO TB329.

This group includes BANDO TB329, CLOYES B329 and GATES T329RB and the remaining parts above.