2011 VPG MV-1 Engine Parts

This table covers lower / conversion gasket sets for oil-pan and related joints. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

4 Conversion / Lower Gasket Set parts are listed for the 2011 VPG MV-1, from ENGINE PRO, FEL-PRO, MAHLE / CLEVITE and 1 other brand.

Part numbers include ENGINE PRO 3797904, FEL-PRO CS97904 and MAHLE / CLEVITE CS5931B, among others listed above.

This table covers the Crankshaft Main Bearing Cap bolts. Read more

One part is listed for the 2011 VPG MV-1 — ARP 1565401.

This table covers the sleeves used to restore a grooved crankshaft seal surface. Read more

7 Crankshaft Repair Sleeve parts for the 2011 VPG MV-1 come from 4 brands — BCA, NATIONAL, WJB / INMOTION PARTS and 1 other brand. The "Popular" part is BCA NS88187.

Listed part numbers: BCA NS88187, NATIONAL 99187 and BCA NS99363, plus the other parts above.

This table covers the Crankshaft Repair Sleeve tools. This is a service tool, not a wear part — match the application in the notes. Read more

This group shows a single part: VICTOR REINZ 711541800.

This table covers the front and rear seals that keep oil in at the crankshaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

14 Crankshaft Seal parts for the 2011 VPG MV-1 come from 7 brands — FEL-PRO, VICTOR REINZ, MAHLE / CLEVITE and 4 other brands. The "Popular" part is FEL-PRO BS40644.

This table covers the bolts that clamp the cylinder head to the block. Read more

3 Cylinder Head Bolt parts are listed for the 2011 VPG MV-1, from ARP, FEL-PRO and MAHLE / CLEVITE.

This group includes ARP 1564101, FEL-PRO ES71328 and MAHLE / CLEVITE GS33269.

This table covers the head gaskets that seal the block to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

6 Cylinder Head Gasket parts are listed for the 2011 VPG MV-1, from FEL-PRO, MAHLE / CLEVITE and VICTOR REINZ. FEL-PRO 26482PT carries the "Popular" badge.

This group includes FEL-PRO 26482PT, FEL-PRO 26483PT and MAHLE / CLEVITE 54759 and the remaining parts above.

This table covers multi-piece gasket sets for a cylinder-head job. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

3 Cylinder Head Gasket Set parts are listed for the 2011 VPG MV-1, from FEL-PRO and MAHLE / CLEVITE.

Listed part numbers: FEL-PRO HS26482PT2, FEL-PRO HS26482PT2VK and MAHLE / CLEVITE HS54760.

This table covers the Harmonic Balancer bolts. Read more

This group shows a single part: ARP 1562501.

This table covers the wear sleeves used to restore a Harmonic Balancer seal surface. Read more

3 Harmonic Balancer Repair Sleeve parts for the 2011 VPG MV-1 come from 3 brands — BCA, NATIONAL and WJB / INMOTION PARTS.

Listed part numbers: BCA NS88187, NATIONAL 88187 and WJB / INMOTION PARTS WS88187.

This table covers the gaskets between the intake manifold and the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

3 Intake Manifold Gasket parts are listed for the 2011 VPG MV-1, from MAHLE / CLEVITE and FEL-PRO.

Part numbers include FEL-PRO MS962811, MAHLE / CLEVITE MS19370 and MAHLE / CLEVITE MS19371.

This table covers the gaskets that seal the Intake Plenum. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

2 Intake Plenum Gasket parts for the 2011 VPG MV-1 come from 2 brands — FEL-PRO and MAHLE / CLEVITE.

This group includes FEL-PRO MS92614 and MAHLE / CLEVITE MS19372.

This table covers the crush washers and gaskets under the oil drain plug. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

2 Oil Drain Plug Gasket parts are listed for the 2011 VPG MV-1, from FEL-PRO and MAHLE / CLEVITE.

This group includes FEL-PRO 72515 and MAHLE / CLEVITE 72112.

This table covers the oil filters that screw onto this engine's filter mount. Typical signs include low oil pressure after a service, or a filter that will not spin off because the old gasket stayed on the block. Lube the new gasket and tighten to the spec on the box; a double-gasket install dumps the sump on the first drive. Read more

10 Oil Filter parts for the 2011 VPG MV-1 come from 7 brands — BOSCH, VARIOUS MFR, WIX and 4 other brands. The "Popular" part is WIX 51372XP.

The Economy section lists 4 options from BOSCH, FVP, PRO-TEC and 1 other brand — the catalog's value-priced group. BOSCH 72227WS is listed in this group.

The High Performance / Heavy Duty section lists 2 options from WIX and MOBIL — grouped under the catalog's "High Performance / Heavy Duty" designation — the notes column spells out what sets them apart. WIX 51372XP is listed in this group.

In the Standard Replacement grade, WIX, BOSCH, MAHLE / CLEVITE and 1 other brand supply 4 parts: built to original-equipment specification. A representative part number is WIX 51372.

This table covers the Oil Filter Adapter Gasket O-rings. Typical signs include a seep at a fitting or a housing that weeps after a service. Lube the new O-ring with the fluid it will see, and do not roll it into the groove. Read more

3 Oil Filter Adapter Gasket / O-Ring parts are listed for the 2011 VPG MV-1, from FEL-PRO and MAHLE / CLEVITE.

Listed part numbers: FEL-PRO 70801, FEL-PRO ES73132 and MAHLE / CLEVITE B31584.

This table covers the gaskets between the oil pan and the block. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

4 Oil Pan Gasket parts for the 2011 VPG MV-1 come from 4 brands — FEL-PRO, MAHLE / CLEVITE, SKP and 1 other brand.

This group includes FEL-PRO OS30725R, MAHLE / CLEVITE OS32517 and SKP SKOS30725R and the remaining parts above.

This table covers the Timing Camshaft Gear bolts. Read more

One part is listed for the 2011 VPG MV-1 — ARP 2561001.

This table covers the seals at the Timing Chain Tensioner Gasket. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

One part is listed for the 2011 VPG MV-1 — FEL-PRO ES73226.

This table covers the gaskets that seal the Timing Cover. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

2 Timing Cover Gasket parts for the 2011 VPG MV-1 come from 2 brands — FEL-PRO and MAHLE / CLEVITE.

Part numbers include FEL-PRO TCS458691 and MAHLE / CLEVITE JV5042.

This table covers the wear sleeves used to restore a Timing Cover seal surface. Read more

This group shows a single part: FEL-PRO 16207.

This table covers the seals at the Timing Cover. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

This group shows a single part: MAHLE / CLEVITE 48322.

This table covers the gaskets that seal the valve cover to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

3 Valve Cover Gasket parts for the 2011 VPG MV-1 come from 3 brands — FEL-PRO, MAHLE / CLEVITE and VICTOR REINZ.

This group includes FEL-PRO VS50564R, MAHLE / CLEVITE VS50355 and VICTOR REINZ 151070101.

This table covers the seals on each valve stem that control oil into the guides. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

2 Valve Stem Seal parts for the 2011 VPG MV-1 come from 2 brands — FEL-PRO and MAHLE / CLEVITE.

Listed part numbers: FEL-PRO SS72891 and MAHLE / CLEVITE SS45892.