2010 Chrysler Sebring Engine Parts

This table covers the gaskets that seal the Camshaft Housing. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

This group shows a single part: FEL-PRO ES73216.

This table covers the wear sleeves used to restore a Camshaft seal surface. Read more

6 Camshaft Repair Sleeve parts are listed for the 2010 Chrysler Sebring, from SKF, TIMKEN, BCA and 3 other brands. SKF 99146 carries the "Popular" badge.

Listed part numbers: SKF 99146, TIMKEN KWK99112 and BCA NS99146, plus the other parts above.

This table covers the seals at each camshaft end. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

12 Camshaft Seal parts are listed for the 2010 Chrysler Sebring, from APEX, FEL-PRO, MAHLE / CLEVITE and 9 other brands. APEX ATC2360 carries the "Popular" badge.

This table covers the bearings in the connecting-rod big ends. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

4 Connecting Rod Bearing parts for the 2010 Chrysler Sebring come from 3 brands — MAHLE / CLEVITE, KING ENGINE BEARINGS and SEALED POWER.

This group includes KING ENGINE BEARINGS CR6810SI, MAHLE / CLEVITE CB1881A6 and MAHLE / CLEVITE CB1881A and the remaining parts above.

This table covers lower / conversion gasket sets for oil-pan and related joints. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

6 Conversion / Lower Gasket Set parts for the 2010 Chrysler Sebring come from 6 brands — APEX, FEL-PRO, AJUSA and 3 other brands. The "Popular" part is APEX ACS2123.

Listed part numbers: APEX ACS2123, FEL-PRO CS95052 and AJUSA 54165400, plus the other parts above.

This table covers the main bearings that support the crankshaft in the block. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

One part is listed for the 2010 Chrysler Sebring — KING ENGINE BEARINGS MB4103SI.

This table covers the gaskets that seal the Crankshaft Main Bearing. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

This group shows a single part: ULTRA-POWER BS40734.

This table covers the sleeves used to restore a grooved crankshaft seal surface. Read more

3 Crankshaft Repair Sleeve parts are listed for the 2010 Chrysler Sebring, from SCHAEFFLER, TIMKEN and WJB / INMOTION PARTS.

This group includes SCHAEFFLER SR3462, TIMKEN KWK99112 and WJB / INMOTION PARTS WS99112.

This table covers the Crankshaft Repair Sleeve tools. This is a service tool, not a wear part — match the application in the notes. Read more

One part is listed for the 2010 Chrysler Sebring — VICTOR REINZ 711457400.

This table covers the front and rear seals that keep oil in at the crankshaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

20 Crankshaft Seal parts are listed for the 2010 Chrysler Sebring, from FEL-PRO, VICTOR REINZ, TIMKEN and 7 other brands. BCA NS3638 carries the "Popular" badge.

This table covers the bolts that clamp the cylinder head to the block. Read more

5 Cylinder Head Bolt parts for the 2010 Chrysler Sebring come from 5 brands — FEL-PRO, AJUSA, APEX and 2 other brands. The "Popular" part is FEL-PRO ES72895.

This group includes FEL-PRO ES72895, AJUSA 81050400 and APEX AHB236 and the remaining parts above.

This table covers the head gaskets that seal the block to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

12 Cylinder Head Gasket parts for the 2010 Chrysler Sebring come from 6 brands — APEX, FEL-PRO, ELRING and 3 other brands. The "Popular" part is APEX AHG280L.

This table covers multi-piece gasket sets for a cylinder-head job. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

11 Cylinder Head Gasket Set parts for the 2010 Chrysler Sebring come from 8 brands — AJUSA, ELRING, FEL-PRO and 5 other brands. The "Popular" part is APEX AHS2123.

This table covers the Cylinder Head Spacer shims. Read more

2 Cylinder Head Spacer Shim parts for the 2010 Chrysler Sebring come from SBI.

Listed part numbers: SBI 2302072L and SBI 2302072R.

This table covers the wear sleeves used to restore a Cylinder seal surface. Read more

2 Cylinder Repair Sleeve parts for the 2010 Chrysler Sebring come from MELLING.

This group includes MELLING CSL173 and MELLING CSL273.

This table covers the block heaters that warm the coolant or oil in cold weather. Read more

One part is listed for the 2010 Chrysler Sebring — KAT'S HEATERS 11814.

This table covers the Engine covers. Read more

This group shows a single part: TECHPRO CH1228112.

This table covers full gasket kits covering the joints opened in an engine rebuild. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

3 Engine Kit Gasket Set parts for the 2010 Chrysler Sebring come from 2 brands — AJUSA and MAHLE / CLEVITE.

Part numbers include AJUSA 50292900, AJUSA 50292800 and MAHLE / CLEVITE 953643.

This table covers the exhaust valves that let combustion gas out of the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

3 Exhaust Valve parts are listed for the 2010 Chrysler Sebring, from MAHLE / CLEVITE, QUALCAST and SKP.

Listed part numbers: MAHLE / CLEVITE 2113214, QUALCAST 101713 and SKP SKV2787.

This table covers the crankshaft pulleys / harmonic balancers at the front of the engine. Read more

4 Harmonic Balancer parts for the 2010 Chrysler Sebring come from 4 brands — SKP, ATP, DAYCO and 1 other brand.

The Economy section lists 1 option from SKP — the catalog's value-priced group. SKP SK594737 is listed in this group.

In the Standard Replacement grade, ATP, DAYCO and ULTRA-POWER supply 3 parts: built to original-equipment specification. A representative part number is ATP 102381.

Listed part numbers: SKP SK594737, ATP 102381 and DAYCO PB1725N, plus the other parts above.

This table covers the Intake Manifold actuators. Typical signs include a door or range that will not move, or a click with no motion. Confirm the command signal before replacing the actuator — a failed module looks the same. Read more

3 Intake Manifold Actuator parts for the 2010 Chrysler Sebring come from 3 brands — DORMAN, MOPAR and SKP.

Part numbers include DORMAN 911406, MOPAR 68020076AB and SKP SK911406.

This table covers the gaskets between the intake manifold and the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

5 Intake Manifold Gasket parts for the 2010 Chrysler Sebring come from 4 brands — MAHLE / CLEVITE, FEL-PRO, APEX and 1 other brand. The "Popular" part is FEL-PRO MS921651.

This group includes FEL-PRO MS921651, APEX AMS2801 and MAHLE / CLEVITE MS16210B and the remaining parts above.

This table covers the Intake Manifold Runner Control Valve solenoids. Typical signs include a harsh or missing shift, or a code for this solenoid circuit. Check resistance and the connector before dropping the pan for a solenoid. Read more

This group shows a single part: ULTRA-POWER 911406.

This table covers the gaskets that seal the Intake Plenum. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

7 Intake Plenum Gasket parts are listed for the 2010 Chrysler Sebring, from AJUSA, FEL-PRO, APEX and 3 other brands. FEL-PRO MS96324 carries the "Popular" badge.

Listed part numbers: FEL-PRO MS96324, AJUSA 00986200 and AJUSA 01209900, plus the other parts above.

This table covers the intake valves that let air (and fuel, on port-injected engines) into the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

4 Intake Valve parts are listed for the 2010 Chrysler Sebring, from MAHLE / CLEVITE, MELLING, QUALCAST and 1 other brand.

Listed part numbers: MAHLE / CLEVITE 2114122, MELLING V1901 and QUALCAST 101901, plus the other parts above.

This table covers the mounts that hold the engine to the chassis. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes. Read more

17 Motor Mount parts are listed for the 2010 Chrysler Sebring, from WESTAR, PIONEER, ANCHOR and 3 other brands. SKP SKM3155 carries the "Popular" badge.

Economy: 2 parts, from SKP. A representative part number is SKP SKM3155.

The Standard Replacement section: 15 options from WESTAR, PIONEER, ANCHOR and 2 other brands. ANCHOR 3152 is listed in this group.

This table covers the Motor Mount bushings. Typical signs include a clunk over bumps, or a torn or walked-out bushing you can see. Press the new bushing square. A cocked bushing will tear in a few thousand miles. Read more

4 Motor Mount Bushing parts are listed for the 2010 Chrysler Sebring, from DEA / MARMON RIDE CONTROL and PIONEER.

Listed part numbers: DEA / MARMON RIDE CONTROL A5445, DEA / MARMON RIDE CONTROL A5489 and PIONEER 605445, plus the other parts above.

This table covers the Motor Mount kits. Read more

2 Motor Mount Kit parts are listed for the 2010 Chrysler Sebring, from ANCHOR and WESTAR.

Listed part numbers: ANCHOR 300609 and WESTAR ETK053.

This table covers the engine oils listed by grade and specification for this engine. Typical signs include a low-oil lamp, knocking after a long interval, or oil that has gone thin and black well before the next service. Match the viscosity and spec in the notes (and on the filler cap). The tables group grades — they are not interchangeable. Read more

13 Oil parts are listed for the 2010 Chrysler Sebring, from VALVOLINE, IDEMITSU, MOBIL and 1 other brand. VALVOLINE 797578 carries the "Popular" badge.

In the Conventional grade, VALVOLINE supplies 2 parts: grouped under the catalog's "Conventional" designation — the notes column spells out what sets them apart. A representative part number is VALVOLINE 797578.

In the Full Synthetic grade, IDEMITSU and VALVOLINE supply 5 parts: full-synthetic oils. A representative part number is IDEMITSU 30015204750.

The High Mileage (>75,000 Miles) section lists 4 options from VALVOLINE — oils grouped for high-mileage engines. VALVOLINE 881161 is listed in this group.

In the Synthetic Blend grade, MOBIL and ACDELCO supply 2 parts: synthetic-blend oils. A representative part number is MOBIL 124406.

This table covers the Oil Cooler Mounting kits. Read more

2 Oil Cooler Mounting Kit parts for the 2010 Chrysler Sebring come from HAYDEN.

Listed part numbers: HAYDEN 238 and HAYDEN 153.

This table covers the Oil Dipstick tubes. Read more

DORMAN supplies both parts for the 2010 Chrysler Sebring.

Listed part numbers: DORMAN 921125 and DORMAN 921126.

This table covers the drain plugs in the oil pan. Read more

7 Oil Drain Plug parts are listed for the 2010 Chrysler Sebring, from DORMAN, ELRING, AGS and 1 other brand. AGS ODP00007 carries the "Popular" badge.

This group includes AGS ODP00007, DORMAN 090053 and DORMAN 090115 and the remaining parts above.

This table covers the crush washers and gaskets under the oil drain plug. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

4 Oil Drain Plug Gasket parts for the 2010 Chrysler Sebring come from 4 brands — ELRING, FEL-PRO, MAHLE / CLEVITE and 1 other brand.

Part numbers include ELRING 176090, FEL-PRO 70822 and MAHLE / CLEVITE 2051, among others listed above.

This table covers the caps on the oil filler neck. Read more

5 Oil Filler Cap parts are listed for the 2010 Chrysler Sebring, from MOTORAD, CALORSTAT, GATES and 2 other brands. MOTORAD MO158 carries the "Popular" badge.

Listed part numbers: MOTORAD MO158, CALORSTAT OC2334 and GATES 31299, plus the other parts above.

This table covers the oil filters that screw onto this engine's filter mount. Typical signs include low oil pressure after a service, or a filter that will not spin off because the old gasket stayed on the block. Lube the new gasket and tighten to the spec on the box; a double-gasket install dumps the sump on the first drive. Read more

16 Oil Filter parts are listed for the 2010 Chrysler Sebring, from VARIOUS MFR, WIX, ACDELCO and 10 other brands. WIX 57060XP carries the "Popular" badge.

Economy: 5 parts, from FRAM, FVP, PRO-TEC and 2 other brands. A representative part number is FRAM FE10060.

In the High Performance / Heavy Duty grade, WIX and MOBIL supply 2 parts: grouped under the catalog's "High Performance / Heavy Duty" designation — the notes column spells out what sets them apart. A representative part number is WIX 57060XP.

The Standard Replacement section: 9 options from ACDELCO, BOSCH, WIX and 5 other brands. ACDELCO PF48 is listed in this group.

This table covers the oil pans that hold the engine's oil sump. Read more

5 Oil Pan parts for the 2010 Chrysler Sebring come from 5 brands — SKP, ATP, DORMAN and 2 other brands. The "Popular" part is SKP SK264855.

This group includes SKP SK264855, ATP 103671 and DORMAN 264855 and the remaining parts above.

This table covers the gaskets between the oil pan and the block. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

6 Oil Pan Gasket parts are listed for the 2010 Chrysler Sebring, from FEL-PRO, AJUSA, APEX and 3 other brands. FEL-PRO OS30754R carries the "Popular" badge.

Part numbers include FEL-PRO OS30754R, AJUSA 14095900 and APEX AOP280A, among others listed above.

This table covers the Oil Pressure Relief valves. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

One part is listed for the 2010 Chrysler Sebring — MOPAR 2843208.

This table covers the Oil pumps. Typical signs include noise from the pump, no pressure, or fluid that never arrives at the outlet. Prime or fill the pump as the notes require. A dry start is a common way to kill a new unit. Read more

One part is listed for the 2010 Chrysler Sebring — MELLING M521.

This table covers the pistons that travel in each cylinder. Typical signs include knock, blow-by, or a cylinder that will not hold compression. Piston work is a short-block job. Match bore, pin and ring pack in the notes — not the photo. Read more

2 Piston parts for the 2010 Chrysler Sebring come from MAHLE / CLEVITE.

This group includes MAHLE / CLEVITE 2243854 and MAHLE / CLEVITE 2243854WR.

This table covers the Piston Pin bushings. Typical signs include a clunk over bumps, or a torn or walked-out bushing you can see. Press the new bushing square. A cocked bushing will tear in a few thousand miles. Read more

One part is listed for the 2010 Chrysler Sebring — MAHLE / CLEVITE 2233721.

This table covers the rings that seal each piston to the cylinder wall. Read more

5 Piston Ring parts for the 2010 Chrysler Sebring come from 3 brands — HASTINGS MANUFACTURING, MAHLE / CLEVITE and SEALED POWER. The "Popular" part is HASTINGS MANUFACTURING 2C4890.

In the Premium grade, HASTINGS MANUFACTURING, MAHLE / CLEVITE and SEALED POWER supply 3 parts: a step above OE specification in materials, tolerances or warranty terms. A representative part number is HASTINGS MANUFACTURING 2M4890S.

Standard Replacement: 2 parts, from HASTINGS MANUFACTURING. A representative part number is HASTINGS MANUFACTURING 2C4890.

Listed part numbers: HASTINGS MANUFACTURING 2C4890, HASTINGS MANUFACTURING 2M4890S and MAHLE / CLEVITE 41856CP, plus the other parts above.

This table covers the rocker arms that transfer cam motion to the valves. Read more

MOPAR supplies the 3 Rocker Arm parts for the 2010 Chrysler Sebring.

Part numbers include MOPAR 4573459, MOPAR 4573460 and MOPAR 4663996.

This table covers the Thrust washers. Read more

One part is listed for the 2010 Chrysler Sebring — KING ENGINE BEARINGS TW170AM.

This table covers the Timing belts. Typical signs include squeal on cold start, cracked ribs, or glazing. Spin the tensioner and idlers by hand while the belt is off. Read more

9 Timing Belt parts for the 2010 Chrysler Sebring come from 9 brands — CLOYES, ITM ENGINE COMPONENTS, ULTRA-POWER and 6 other brands. The "Popular" part is DAYCO 95295.

The Economy section: 3 options from CLOYES, ITM ENGINE COMPONENTS and ULTRA-POWER. CLOYES B295 is listed in this group.

Standard Replacement: 6 parts, from DAYCO, GATES, ACDELCO and 3 other brands. A representative part number is DAYCO 95295.

Listed part numbers: DAYCO 95295, CLOYES B295 and ITM ENGINE COMPONENTS 4298, plus the other parts above.

This table covers the Timing Belt & component kits. Read more

14 Timing Belt & Component Kit parts are listed for the 2010 Chrysler Sebring, from DAYCO, GATES, ACDELCO and 5 other brands. CONTINENTAL PP295LK3 carries the "Popular" badge.

Economy: 1 part, from CLOYES. A representative part number is CLOYES BK295A.

The Standard Replacement section: 13 options from DAYCO, GATES, ACDELCO and 4 other brands. CONTINENTAL PP295LK3 is listed in this group.