2020 Honda CR-V Engine Parts

This table covers the chains that drive the balance shafts. Read more

3 Balance Shaft Chain parts are listed for the 2020 Honda CR-V, from S.A. GEAR and INA.

Listed part numbers: INA ZC1021320, S.A. GEAR C1180 and S.A. GEAR 76413P.

This table covers the guides that keep the balance-shaft chain on its path. Read more

One part is listed for the 2020 Honda CR-V — S.A. GEAR 71262.

This table covers the Balance Shaft Chain tensioners. Typical signs include belt flutter, a chirp that returns after a new belt, or an arm that no longer damps. Replace the tensioner with the belt at higher mileage. Read more

This group shows a single part: S.A. GEAR 91347.

This table covers the Balance Shaft sprockets. Read more

One part is listed for the 2020 Honda CR-V — S.A. GEAR S1474.

This table covers the bearings in the connecting-rod big ends. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

One part is listed for the 2020 Honda CR-V — MAHLE / CLEVITE CB1976A4.

This table covers lower / conversion gasket sets for oil-pan and related joints. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

One part is listed for the 2020 Honda CR-V — AJUSA 54337000.

This table covers the main bearings that support the crankshaft in the block. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

This group shows a single part: TOPLINE TWH36.

This table covers the front and rear seals that keep oil in at the crankshaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

10 Crankshaft Seal parts for the 2020 Honda CR-V come from 7 brands — FEL-PRO, AJUSA, APEX and 4 other brands. The "Popular" part is FEL-PRO TCS46051.

This table covers the bolts that clamp the cylinder head to the block. Read more

5 Cylinder Head Bolt parts are listed for the 2020 Honda CR-V, from MAHLE / CLEVITE, AJUSA, APEX and 2 other brands. MAHLE / CLEVITE GS33604 carries the "Popular" badge.

This group includes MAHLE / CLEVITE GS33604, AJUSA 81041700 and APEX AHB160 and the remaining parts above.

This table covers the head gaskets that seal the block to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

One part is listed for the 2020 Honda CR-V — AJUSA 10275000.

This table covers multi-piece gasket sets for a cylinder-head job. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

One part is listed for the 2020 Honda CR-V — AJUSA 52652500.

This table covers the Engine covers. Read more

5 Engine Cover parts are listed for the 2020 Honda CR-V, from TECHPRO and VARIOUS MFR. TECHPRO HO1228150 carries the "Popular" badge.

Listed part numbers: TECHPRO HO1228150, TECHPRO HO1228157 and TECHPRO HO1228180, plus the other parts above.

This table covers full gasket kits covering the joints opened in an engine rebuild. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

One part is listed for the 2020 Honda CR-V — AJUSA 50580500.

This table covers the followers that drive a mechanical fuel pump off the camshaft. Read more

One part is listed for the 2020 Honda CR-V — WELLS 5T5001.

This table covers the gaskets between the intake manifold and the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

4 Intake Manifold Gasket parts are listed for the 2020 Honda CR-V, from AJUSA, BECK/ARNLEY, FEL-PRO and 1 other brand.

Part numbers include AJUSA 13279400, BECK/ARNLEY 0376246 and FEL-PRO MS98028, among others listed above.

This table covers the mounts that hold the engine to the chassis. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes. Read more

4 Motor Mount parts for the 2020 Honda CR-V come from 4 brands — ANCHOR, DEA / MARMON RIDE CONTROL, PIONEER and 1 other brand.

Part numbers include ANCHOR 10093, DEA / MARMON RIDE CONTROL A65157 and PIONEER 610093, among others listed above.

This table covers the Motor Mount kits. Read more

This group shows a single part: ANCHOR 300889.

This table covers the engine oils listed by grade and specification for this engine. Typical signs include a low-oil lamp, knocking after a long interval, or oil that has gone thin and black well before the next service. Match the viscosity and spec in the notes (and on the filler cap). The tables group grades — they are not interchangeable. Read more

37 Oil parts for the 2020 Honda CR-V come from 6 brands — LIQUI MOLY, VALVOLINE, MOBIL and 3 other brands. The "Popular" part is LIQUI MOLY 22044. They are grouped as Full Synthetic and High Mileage (>75,000 Miles), with Full Synthetic the largest group at 30 parts from LIQUI MOLY, VALVOLINE, MOBIL and 3 other brands.

This table covers the drain plugs in the oil pan. Read more

6 Oil Drain Plug parts for the 2020 Honda CR-V come from 4 brands — DORMAN, AGS, REIN and 1 other brand. The "Popular" part is DORMAN 090033.

Listed part numbers: DORMAN 090033, DORMAN 090053 and AGS ODP00007, plus the other parts above.

This table covers the crush washers and gaskets under the oil drain plug. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

5 Oil Drain Plug Gasket parts are listed for the 2020 Honda CR-V, from DORMAN, AJUSA, APEX and 2 other brands. DORMAN 095144 carries the "Popular" badge.

This group includes DORMAN 095144, AJUSA 22007400 and APEX ADP1909 and the remaining parts above.

This table covers the caps on the oil filler neck. Read more

3 Oil Filler Cap parts for the 2020 Honda CR-V come from 3 brands — CALORSTAT, GATES and MOTORAD.

Listed part numbers: CALORSTAT OC2335, GATES 31284 and MOTORAD MO159.

This table covers the oil filters that screw onto this engine's filter mount. Typical signs include low oil pressure after a service, or a filter that will not spin off because the old gasket stayed on the block. Lube the new gasket and tighten to the spec on the box; a double-gasket install dumps the sump on the first drive. Read more

13 Oil Filter parts for the 2020 Honda CR-V come from 10 brands — BOSCH, VARIOUS MFR, WIX and 7 other brands. The "Popular" part is WIX 57356XP.

The Economy section lists 4 options from BOSCH, FVP, PRO-TEC and 1 other brand — the catalog's value-priced group. BOSCH 72226WS is listed in this group.

The High Performance / Heavy Duty section lists 2 options from WIX and MOBIL — grouped under the catalog's "High Performance / Heavy Duty" designation — the notes column spells out what sets them apart. WIX 57356XP is listed in this group.

In the Standard Replacement grade, BOSCH, WIX, BECK/ARNLEY and 4 other brands supply 7 parts: built to original-equipment specification. A representative part number is BOSCH 3323.

This table covers the Oil Filter Adapter Gasket O-rings. Typical signs include a seep at a fitting or a housing that weeps after a service. Lube the new O-ring with the fluid it will see, and do not roll it into the groove. Read more

2 Oil Filter Adapter Gasket / O-Ring parts are listed for the 2020 Honda CR-V, from FEL-PRO and MAHLE / CLEVITE.

Listed part numbers: FEL-PRO ES71858 and MAHLE / CLEVITE B33713.

This table covers the Oil Filter Support tubes. Read more

One part is listed for the 2020 Honda CR-V — AUTOTECNICA HA1416938.

This table covers the oil pans that hold the engine's oil sump. Read more

2 Oil Pan parts are listed for the 2020 Honda CR-V, from DORMAN and SPECTRA PREMIUM.

This group includes DORMAN 264554 and SPECTRA PREMIUM HOP41A.

This table covers the gaskets between the oil pan and the block. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

This group shows a single part: VICTOR REINZ 703141410.

This table covers the seals at the Oil Pressure Sender / Switch. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

This group shows a single part: FEL-PRO 73196.

This table covers the seals at the Oil Pump. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

One part is listed for the 2020 Honda CR-V — AJUSA 77007000.

This table covers the Timing Cam sprockets. Read more

4 Timing Cam Sprocket parts for the 2020 Honda CR-V come from 4 brands — CLOYES, FVP, INA and 1 other brand.

This group includes CLOYES S1030 and INA ZSS1030 and the remaining parts above.

This table covers the timing chains that keep the cams in time with the crank. Read more

One part is listed for the 2020 Honda CR-V — S.A. GEAR C1179.

This table covers kits that group a timing chain with the related tensioners and guides. Read more

4 Timing Chain & Component Kit parts for the 2020 Honda CR-V come from 2 brands — S.A. GEAR and INA.

The Economy section: 2 options from S.A. GEAR. S.A. GEAR 76414T is listed in this group.

Standard Replacement: 2 parts, from INA. A representative part number is INA ZC1021300.

Listed part numbers: S.A. GEAR 76414T, S.A. GEAR 76414 and INA ZC1021300, plus the other parts above.

This table covers the guides and dampers that keep the timing chain on its path. Read more

4 Timing Chain Guide / Damper parts are listed for the 2020 Honda CR-V, from S.A. GEAR and INA.

Listed part numbers: INA ZG0774, S.A. GEAR 71261 and S.A. GEAR 71265, plus the other parts above.

This table covers the tensioners that keep the timing chain taut. Typical signs include belt flutter, a chirp that returns after a new belt, or an arm that no longer damps. Replace the tensioner with the belt at higher mileage. Read more

2 Timing Chain Tensioner parts for the 2020 Honda CR-V come from 2 brands — INA and S.A. GEAR.

Part numbers include INA ZT0691 and S.A. GEAR 91355.

This table covers the gaskets that seal the Timing Cover. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

This group shows a single part: AJUSA 77006900.

This table covers the seals at the Timing Cover. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

3 Timing Cover Seal parts for the 2020 Honda CR-V come from 3 brands — MAHLE / CLEVITE, SKF and VICTOR REINZ.

Part numbers include MAHLE / CLEVITE 68064, SKF 16896 and VICTOR REINZ 815380700.

This table covers the crankshaft sprockets that drive the timing chain or belt. Read more

This group shows a single part: S.A. GEAR S1473.

This table covers the Torque Strut mounts. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes. Read more

6 Torque Strut Mount parts are listed for the 2020 Honda CR-V, from ANCHOR, WESTAR, DEA / MARMON RIDE CONTROL and 1 other brand. ANCHOR 10065 carries the "Popular" badge.

Listed part numbers: ANCHOR 10065, WESTAR EM7400 and ANCHOR 10223, plus the other parts above.

This table covers the gaskets that seal the valve cover to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

4 Valve Cover Gasket parts for the 2020 Honda CR-V come from 4 brands — AJUSA, BECK/ARNLEY, FEL-PRO and 1 other brand.

Part numbers include AJUSA 11146000, BECK/ARNLEY 0362085 and FEL-PRO VS50976R, among others listed above.

This table covers the pressed-in bronze and cast-iron guides that align valve stems. Typical signs include oil smoke on startup, a guide that has gone oval, or a valve that no longer seats quietly. Guides are a machine-shop fit. Confirm stem diameter in the notes before ordering. Read more

4 Valve Guide parts for the 2020 Honda CR-V come from 4 brands — ENGINETECH, QUALCAST, SBI and 1 other brand.

Part numbers include ENGINETECH GD8158, QUALCAST 308158 and SBI 1408158, among others listed above.

This table covers the lifters / tappets that transfer cam motion to the valves. Read more

This group shows a single part: AJUSA 85022000.

This table covers the keepers that lock each valve-spring retainer to the stem. Read more

One part is listed for the 2020 Honda CR-V — QUALCAST 345008.

This table covers the seals on each valve stem that control oil into the guides. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

8 Valve Stem Seal parts for the 2020 Honda CR-V come from 6 brands — MAHLE / CLEVITE, SBI, APEX and 3 other brands. The "Popular" part is APEX AVS1003.

Part numbers include APEX AVS1003, FEL-PRO SS702831 and AJUSA 57030200, among others listed above.

This table covers the oil-control solenoids that command the cam phasers. Typical signs include a door or range that will not move, or a click with no motion. Confirm the command signal before replacing the actuator — a failed module looks the same. Read more

This group shows a single part: STANDARD MOTOR PRODUCTS VVT472.

This table covers the Variable Valve Timing (VVT) Solenoid filters. Typical signs include restricted flow — long cranking, weak airflow, or dirty fluid after a short interval. Seat the new filter so it cannot bypass, and use the grade the notes call for. Read more

2 Variable Valve Timing (VVT) Solenoid Filter parts for the 2020 Honda CR-V come from 2 brands — AJUSA and FEL-PRO.

Listed part numbers: AJUSA 01156600 and FEL-PRO ES73320.

This table covers the cam phaser sprockets used by the variable-valve-timing system. Read more

This group shows a single part: STANDARD MOTOR PRODUCTS VVT475.