2008 Chrysler Pacifica Engine Parts

This table covers the gaskets that seal the Camshaft Housing. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

One part is listed for the 2008 Chrysler Pacifica — FEL-PRO ES73216.

This table covers the wear sleeves used to restore a Camshaft seal surface. Read more

5 Camshaft Repair Sleeve parts for the 2008 Chrysler Pacifica come from 5 brands — TIMKEN, BCA, NATIONAL and 2 other brands. The "Popular" part is TIMKEN KWK99112.

Part numbers include TIMKEN KWK99112, BCA NS99146 and NATIONAL 99146, among others listed above.

This table covers the Camshaft Retainer / Thrust plates. Typical signs include warpage, cracks, or a plate that no longer locates the assembly. Confirm which plate the notes describe — backing plates, clutch plates and strike plates are different parts. Read more

This group shows a single part: MOPAR 4556518AB.

This table covers the seals at each camshaft end. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

13 Camshaft Seal parts for the 2008 Chrysler Pacifica come from 12 brands — MOPAR, APEX, FEL-PRO and 9 other brands. The "Popular" part is APEX ATC2360.

This table covers the bearings in the connecting-rod big ends. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

4 Connecting Rod Bearing parts are listed for the 2008 Chrysler Pacifica, from MAHLE / CLEVITE, ENGINETECH and SEALED POWER.

This group includes ENGINETECH BB139J, MAHLE / CLEVITE CB1881A6 and MAHLE / CLEVITE CB1881A and the remaining parts above.

This table covers lower / conversion gasket sets for oil-pan and related joints. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

7 Conversion / Lower Gasket Set parts are listed for the 2008 Chrysler Pacifica, from ENGINETECH, FEL-PRO, AJUSA and 4 other brands. ENGINETECH CR241CSA carries the "Popular" badge.

Part numbers include ENGINETECH CR241CSA, FEL-PRO CS95052 and AJUSA 54165400, among others listed above.

This table covers the main bearings that support the crankshaft in the block. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

3 Crankshaft Main Bearing parts for the 2008 Chrysler Pacifica come from 3 brands — ENGINETECH, MAHLE / CLEVITE and MOPAR.

Listed part numbers: ENGINETECH BC508J, MAHLE / CLEVITE MS2303A and MOPAR 68002265AA.

This table covers the gaskets that seal the Crankshaft Main Bearing. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

One part is listed for the 2008 Chrysler Pacifica — ULTRA-POWER BS40734.

This table covers the sleeves used to restore a grooved crankshaft seal surface. Read more

3 Crankshaft Repair Sleeve parts for the 2008 Chrysler Pacifica come from 3 brands — SCHAEFFLER, TIMKEN and WJB / INMOTION PARTS.

This group includes SCHAEFFLER SR3462, TIMKEN KWK99112 and WJB / INMOTION PARTS WS99112.

This table covers the Crankshaft Repair Sleeve tools. This is a service tool, not a wear part — match the application in the notes. Read more

This group shows a single part: VICTOR REINZ 711457400.

This table covers the front and rear seals that keep oil in at the crankshaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

23 Crankshaft Seal parts for the 2008 Chrysler Pacifica come from 11 brands — FEL-PRO, APEX, VICTOR REINZ and 8 other brands. The "Popular" part is BCA NS3638.

This table covers the bolts that clamp the cylinder head to the block. Read more

5 Cylinder Head Bolt parts are listed for the 2008 Chrysler Pacifica, from FEL-PRO, APEX, ENGINETECH and 2 other brands. FEL-PRO ES72895 carries the "Popular" badge.

Part numbers include FEL-PRO ES72895, APEX AHB236 and ENGINETECH HB209, among others listed above.

This table covers the head gaskets that seal the block to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

11 Cylinder Head Gasket parts are listed for the 2008 Chrysler Pacifica, from APEX, FEL-PRO, ENGINETECH and 3 other brands. APEX AHG280L carries the "Popular" badge.

This table covers multi-piece gasket sets for a cylinder-head job. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

9 Cylinder Head Gasket Set parts are listed for the 2008 Chrysler Pacifica, from ENGINETECH, FEL-PRO, VICTOR REINZ and 3 other brands. ENGINETECH CR241HSA carries the "Popular" badge.

This group includes ENGINETECH CR241HSA, ENGINETECH CR241HSAWB and AJUSA 52424700 and the remaining parts above.

This table covers the Cylinder Head plugs. Typical signs include a leak at the drain or glow-plug hole, or a plug that has rounded off. Replace the crush washer and torque to the spec in the notes. Read more

This group shows a single part: MOPAR 4556020AB.

This table covers the Cylinder Head Spacer shims. Read more

2 Cylinder Head Spacer Shim parts are listed for the 2008 Chrysler Pacifica, from ENGINETECH and SBI.

Part numbers include ENGINETECH CHS1060 and SBI 2302165.

This table covers the block heaters that warm the coolant or oil in cold weather. Read more

This group shows a single part: MOPAR 4609325.

This table covers full gasket kits covering the joints opened in an engine rebuild. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

2 Engine Kit Gasket Set parts are listed for the 2008 Chrysler Pacifica, from AJUSA and ENGINETECH.

This group includes AJUSA 50388100 and ENGINETECH CR215K7.

This table covers the brackets that mount the Engine Lift. Typical signs include a cracked mount, a rattle, or a bracket that no longer holds alignment. Confirm position in the notes. Many brackets look alike and bolt to different corners. Read more

One part is listed for the 2008 Chrysler Pacifica — MOPAR 4892257AA.

This table covers the exhaust valves that let combustion gas out of the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

5 Exhaust Valve parts for the 2008 Chrysler Pacifica come from 5 brands — SKP, ENGINETECH, MAHLE / CLEVITE and 2 other brands. The "Popular" part is SKP SKV2787.

This group includes SKP SKV2787, ENGINETECH V2787 and MAHLE / CLEVITE 2113214 and the remaining parts above.

This table covers the Expansion plugs. Typical signs include a leak at the drain or glow-plug hole, or a plug that has rounded off. Replace the crush washer and torque to the spec in the notes. Read more

One part is listed for the 2008 Chrysler Pacifica — MELLING MPE831R.

This table covers the crankshaft pulleys / harmonic balancers at the front of the engine. Read more

5 Harmonic Balancer parts are listed for the 2008 Chrysler Pacifica, from SKP, ATP, DAYCO and 2 other brands.

In the Economy grade, SKP supplies 1 part: the catalog's value-priced group. A representative part number is SKP SK594737.

The Standard Replacement section lists 4 options from ATP, DAYCO, MOPAR and 1 other brand — built to original-equipment specification. ATP 102381 is listed in this group.

This group includes SKP SK594737, ATP 102381 and DAYCO PB1725N and the remaining parts above.

This table covers the Intake manifolds. Typical signs include an exhaust tick, a vacuum leak, or a gasket that has burned through. Replace the gaskets and hardware; a warped flange will leak with a new gasket alone. Read more

This group shows a single part: MOPAR 4593578AD.

This table covers the Intake Manifold actuators. Typical signs include a door or range that will not move, or a click with no motion. Confirm the command signal before replacing the actuator — a failed module looks the same. Read more

One part is listed for the 2008 Chrysler Pacifica — MOPAR 4593676AC.

This table covers the Intake Manifold bolts. Read more

One part is listed for the 2008 Chrysler Pacifica — MOPAR 6104124AA.

This table covers the gaskets between the intake manifold and the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

6 Intake Manifold Gasket parts are listed for the 2008 Chrysler Pacifica, from MAHLE / CLEVITE, APEX, FEL-PRO and 2 other brands. APEX AMS2801 carries the "Popular" badge.

This group includes APEX AMS2801, FEL-PRO MS921651 and MAHLE / CLEVITE MS16210B and the remaining parts above.

This table covers the gaskets that seal the Intake Plenum. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

5 Intake Plenum Gasket parts for the 2008 Chrysler Pacifica come from 5 brands — FEL-PRO, APEX, MAHLE / CLEVITE and 2 other brands. The "Popular" part is FEL-PRO MS96324.

Listed part numbers: FEL-PRO MS96324, APEX AMS2800 and MAHLE / CLEVITE MS19537, plus the other parts above.

This table covers the intake valves that let air (and fuel, on port-injected engines) into the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

6 Intake Valve parts for the 2008 Chrysler Pacifica come from 6 brands — MELLING, SKP, ENGINETECH and 3 other brands. The "Popular" part is MELLING V1901.

This group includes MELLING V1901, SKP SKV1901 and ENGINETECH V3408 and the remaining parts above.

This table covers the mounts that hold the engine to the chassis. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes. Read more

10 Motor Mount parts for the 2008 Chrysler Pacifica come from 6 brands — SKP, WESTAR, ANCHOR and 3 other brands. The "Popular" part is SKP SKM3181.

The Economy section: 3 options from SKP and FAMOUS BRAND. SKP SKM3181 is listed in this group.

Standard Replacement: 7 parts, from WESTAR, ANCHOR, DEA / MARMON RIDE CONTROL and 1 other brand. A representative part number is WESTAR EM5085.

This table covers the brackets that mount the Motor Mount. Typical signs include a cracked mount, a rattle, or a bracket that no longer holds alignment. Confirm position in the notes. Many brackets look alike and bolt to different corners. Read more

2 Motor Mount Bracket parts for the 2008 Chrysler Pacifica come from MOPAR.

This group includes MOPAR 4809957AF and MOPAR 4809962AE.

This table covers the isolators in an engine mount. Read more

MOPAR supplies both parts for the 2008 Chrysler Pacifica.

This group includes MOPAR 4880408AD and MOPAR 5510012AA.

This table covers the Motor Mount kits. Read more

This group shows a single part: ANCHOR 301320.

This table covers the engine oils listed by grade and specification for this engine. Typical signs include a low-oil lamp, knocking after a long interval, or oil that has gone thin and black well before the next service. Match the viscosity and spec in the notes (and on the filler cap). The tables group grades — they are not interchangeable. Read more

29 Oil parts for the 2008 Chrysler Pacifica come from 4 brands — VALVOLINE, MOBIL, IDEMITSU and 1 other brand. The "Popular" part is MOBIL 125195. They are grouped as Conventional, Full Synthetic, High Mileage (>75,000 Miles) and Synthetic Blend, with Full Synthetic the largest group at 11 parts from MOBIL, VALVOLINE and IDEMITSU.

This table covers the heat exchangers that cool engine oil. Typical signs include oil at the cooler fittings, or coolant that looks like a milkshake. Pressure-test both circuits after a cooler swap — a leak here mixes oil and coolant. Read more

This group shows a single part: DORMAN 918899.

This table covers the Oil Cooler Mounting kits. Read more

HAYDEN supplies both parts for the 2008 Chrysler Pacifica.

Part numbers include HAYDEN 238 and HAYDEN 153.

This table covers the Oil Dipstick tubes. Read more

3 Oil Dipstick / Tube parts for the 2008 Chrysler Pacifica come from 2 brands — MOPAR and DORMAN.

Part numbers include DORMAN 921188, MOPAR 4593604AA and MOPAR 4593605AA.

This table covers the drain plugs in the oil pan. Read more

7 Oil Drain Plug parts for the 2008 Chrysler Pacifica come from 5 brands — DORMAN, AGS, ELRING and 2 other brands. The "Popular" part is AGS ODP00007.

This group includes AGS ODP00007, DORMAN 090053 and DORMAN 090115 and the remaining parts above.

This table covers the crush washers and gaskets under the oil drain plug. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

5 Oil Drain Plug Gasket parts are listed for the 2008 Chrysler Pacifica, from MAHLE / CLEVITE, APEX, ELRING and 2 other brands. MAHLE / CLEVITE 2051 carries the "Popular" badge.

Listed part numbers: MAHLE / CLEVITE 2051, APEX ADP1902 and ELRING 176090, plus the other parts above.

This table covers the caps on the oil filler neck. Read more

5 Oil Filler Cap parts for the 2008 Chrysler Pacifica come from 5 brands — MOTORAD, CALORSTAT, GATES and 2 other brands. The "Popular" part is MOTORAD MO158.

This group includes MOTORAD MO158, CALORSTAT OC2334 and GATES 31299 and the remaining parts above.

This table covers the Oil Filler tubes. Read more

This group shows a single part: MOPAR 4892264AA.

This table covers the oil filters that screw onto this engine's filter mount. Typical signs include low oil pressure after a service, or a filter that will not spin off because the old gasket stayed on the block. Lube the new gasket and tighten to the spec on the box; a double-gasket install dumps the sump on the first drive. Read more

18 Oil Filter parts for the 2008 Chrysler Pacifica come from 15 brands — BOSCH, VARIOUS MFR, WIX and 12 other brands. The "Popular" part is MOBIL M1204A.

The Economy section: 5 options from BOSCH, FRAM, FVP and 2 other brands. BOSCH 72137WS is listed in this group.

The High Performance / Heavy Duty section lists 2 options from MOBIL and WIX — grouped under the catalog's "High Performance / Heavy Duty" designation — the notes column spells out what sets them apart. MOBIL M1204A is listed in this group.

Standard Replacement: 11 parts, from MOTORCRAFT, WIX, ACDELCO and 8 other brands. A representative part number is MOTORCRAFT FL300.

This table covers the Oil Level Sensor Gasket O-rings. Typical signs include a seep at a fitting or a housing that weeps after a service. Lube the new O-ring with the fluid it will see, and do not roll it into the groove. Read more

This group shows a single part: MOPAR 5003905AA.

This table covers the oil pans that hold the engine's oil sump. Read more

3 Oil Pan parts are listed for the 2008 Chrysler Pacifica, from DORMAN, MOPAR and SPECTRA PREMIUM.

Listed part numbers: DORMAN 264584, MOPAR 4892122AA and SPECTRA PREMIUM CRP62A.

This table covers the gaskets between the oil pan and the block. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

5 Oil Pan Gasket parts for the 2008 Chrysler Pacifica come from 5 brands — FEL-PRO, APEX, MAHLE / CLEVITE and 2 other brands. The "Popular" part is FEL-PRO OS30754R.

Listed part numbers: FEL-PRO OS30754R, APEX AOP280A and MAHLE / CLEVITE OS32285, plus the other parts above.

This table covers the Oil Pressure Relief valves. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

This group shows a single part: MOPAR 2843208.

This table covers the Oil pumps. Typical signs include noise from the pump, no pressure, or fluid that never arrives at the outlet. Prime or fill the pump as the notes require. A dry start is a common way to kill a new unit. Read more

3 Oil Pump parts for the 2008 Chrysler Pacifica come from 3 brands — ENGINETECH, MELLING and MOPAR.

The Economy section: 1 option from ENGINETECH. ENGINETECH EPK156 is listed in this group.

Standard Replacement: 2 parts, from MELLING and MOPAR. A representative part number is MELLING M521.

This group includes ENGINETECH EPK156, MELLING M521 and MOPAR 4663844BA.

This table covers the gaskets that seal the Oil Pump. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

One part is listed for the 2008 Chrysler Pacifica — MOPAR 4648938AC.

This table covers the seals at the Oil Pump. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

One part is listed for the 2008 Chrysler Pacifica — MOPAR 4659945.

This table covers the pistons that travel in each cylinder. Typical signs include knock, blow-by, or a cylinder that will not hold compression. Piston work is a short-block job. Match bore, pin and ring pack in the notes — not the photo. Read more

4 Piston parts are listed for the 2008 Chrysler Pacifica, from ENGINETECH and MAHLE / CLEVITE.

Part numbers include ENGINETECH P6021, ENGINETECH K60216P and MAHLE / CLEVITE 2243778, among others listed above.