2008 Dodge Caliber Drivetrain Parts

This table covers the Axle / Differential assemblies. Read more

One part is listed for the 2008 Dodge Caliber — MOPAR 3501A115.

This table covers the complete CV axle shafts from differential (or hub) to wheel. Typical signs include a click in tight turns, grease flung around the wheel well, or a vibration that builds with speed. A torn boot caught early is a boot kit; caught late it is the whole axle. Torque the axle nut to the method in the notes. Read more

32 CV Axle parts for the 2008 Dodge Caliber come from 7 brands — TOP NOTCH, TRAKMOTIVE, GSP and 4 other brands. The "Popular" part is APWI CH8370. Grades run from Economy through Standard Replacement; Standard Replacement is the most populated section, led by TOP NOTCH, TRAKMOTIVE, GSP and 3 other brands.

This table covers the CV Intermediate shafts. Read more

3 CV Intermediate Shaft parts are listed for the 2008 Dodge Caliber, from GSP, TOP NOTCH and TRAKMOTIVE.

This group includes GSP NEX12012, TOP NOTCH TN30165IS and TRAKMOTIVE CH3512.

This table covers the boots that keep grease in a CV joint. Typical signs include a split boot, grease flung around the joint, or a click once grit is inside. A boot caught early is a kit. Once the joint has clicked, the joint itself is usually worn. Read more

6 CV Joint Boot parts for the 2008 Dodge Caliber come from 2 brands — MEVOTECH and MOPAR. The "Popular" part is MEVOTECH DX900. 4 parts fit every engine; the other 2 are engine-specific.

Listed part numbers: MEVOTECH DX900, MEVOTECH DX268 and MEVOTECH DX591, plus the other parts above.

This table covers the bearings and races that support the differential carrier. Read more

12 Differential Carrier Bearing / Race parts for the 2008 Dodge Caliber come from 6 brands — NATIONAL, SKF, WJB / INMOTION PARTS and 3 other brands. The "Popular" part is WJB / INMOTION PARTS WTA18. Every part fits both the 1.8L L4 and the 2.4L L4.

The Economy section lists 2 options from WJB / INMOTION PARTS — the catalog's value-priced group. WJB / INMOTION PARTS WTA18 is listed in this group.

In the Standard Replacement grade, NATIONAL, SKF, SCHAEFFLER and 2 other brands supply 10 parts: built to original-equipment specification. A representative part number is BCA NBA18.

This table covers the Differential mounts. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes. Read more

5 Differential Mount parts are listed for the 2008 Dodge Caliber, from ANCHOR and WESTAR. ANCHOR 3623 carries the "Popular" badge. 2 parts fit every engine; the other 3 are engine-specific.

Part numbers include ANCHOR 3623, ANCHOR 3462 and ANCHOR 3463, among others listed above.

This table covers the wear sleeves used to restore a grooved pinion seal surface. Read more

2 Differential Pinion Repair Sleeve parts for the 2008 Dodge Caliber come from 2 brands — NATIONAL and WJB / INMOTION PARTS.

Listed part numbers: NATIONAL 99210 and WJB / INMOTION PARTS WS99210.

This table covers the seals at the differential pinion yoke. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

2 Differential Pinion Seal parts for the 2008 Dodge Caliber come from 2 brands — NATIONAL and WJB / INMOTION PARTS.

Part numbers include NATIONAL 711053 and WJB / INMOTION PARTS WS711053.

This table covers the Differential Ring gears. Read more

One part is listed for the 2008 Dodge Caliber — MOPAR 5191029AA.

This table covers the driveshafts that carry torque from the transmission or transfer case. Read more

7 Drive Shaft parts are listed for the 2008 Dodge Caliber, from ULTRA-POWER, WJB / INMOTION PARTS, CARDONE and 4 other brands. ULTRA-POWER 946309 carries the "Popular" badge. 2 parts fit every engine; the other 5 are engine-specific.

This group includes ULTRA-POWER 946309, WJB / INMOTION PARTS WDS46309 and CARDONE 653002 and the remaining parts above.

This table covers the seals at the Drive Shaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

This group shows a single part: MOPAR 5189989AA.

This table covers the gear oils specified for the axle or transfer case. Typical signs include a low-oil lamp, knocking, or oil that has gone thin before the next interval. Match the viscosity and spec in the notes, not just the weight on the bottle. Read more

8 Gear Oil parts for the 2008 Dodge Caliber come from 3 brands — VALVOLINE, LUCAS OIL and MOBIL. The "Popular" part is MOBIL 104361.

The SAE 75W-90 section lists 1 option from MOBIL — grouped under the catalog's "SAE 75W-90" designation — the notes column spells out what sets them apart. MOBIL 104361 is listed in this group.

The SAE 80W-90 section lists 7 options from VALVOLINE and LUCAS OIL — grouped under the catalog's "SAE 80W-90" designation — the notes column spells out what sets them apart. VALVOLINE VV831 is listed in this group.

Part numbers include MOBIL 104361, VALVOLINE VV831 and LUCAS OIL 10043, among others listed above.

This table covers the Power Take Off (PTO) assemblies. Read more

This group shows a single part: MOPAR 5273456AB.

This table covers the fluids specified for the transfer case. Typical signs include discolored fluid, a burnt smell, or a level that keeps dropping. Use only the specification in the notes — the tables group grades because they are not interchangeable. Read more

8 Transfer Case Fluid parts for the 2008 Dodge Caliber come from 3 brands — VALVOLINE, LUCAS OIL and MOBIL. The "Popular" part is MOBIL 104361.

The SAE 75W-90 section: 1 option from MOBIL. MOBIL 104361 is listed in this group.

The SAE 80W-90 section: 7 options from VALVOLINE and LUCAS OIL. VALVOLINE VV831 is listed in this group.

Listed part numbers: MOBIL 104361, VALVOLINE VV831 and LUCAS OIL 10043, plus the other parts above.

This table covers the seals at the Transfer Case Housing Extension. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

2 Transfer Case Housing Extension Seal parts are listed for the 2008 Dodge Caliber, from NATIONAL and WJB / INMOTION PARTS.

This group includes NATIONAL 711135 and WJB / INMOTION PARTS WS711135.

This table covers the wear sleeves used to restore a Transfer Case Output Shaft seal surface. Read more

3 Transfer Case Output Shaft Repair Sleeve parts for the 2008 Dodge Caliber come from 3 brands — BCA, NATIONAL and WJB / INMOTION PARTS. 1 part fits every engine; the other 2 are engine-specific.

Part numbers include BCA NS99166, NATIONAL 99166 and WJB / INMOTION PARTS WS99166.

This table covers the seals at the Transfer Case Output Shaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

2 Transfer Case Output Shaft Seal parts for the 2008 Dodge Caliber come from 2 brands — NATIONAL and WJB / INMOTION PARTS.

Part numbers include NATIONAL 711115 and WJB / INMOTION PARTS WS711115.